Heat & Glo 350X-AU Owner's Manual page 16

REM300-HNG-AU
Fireplace Specific Information
Standard fireplace features vary. Consult the installation
manual for available options.
The included AUX300CE receiver provides additional fea-
tures: Fan control and two Aux functions.
The REM300-HNG-AU remote control system functions
include: On/Off, Thermostat Mode, Timer Countdown,
and Flame Adjustment (for fireplaces with variable flame).
Kit Contents
• REM300-HNG-AU Transmitter
• AAA Batteries (3)
• Wall Holder
• Drywall Anchor (2)
• Screws (2)
Introduction
The RC300AU multifunctional remote control is de-
signed to flame height, fan speed, and up to two
220/240VAC auxiliary functions on your gas fireplace.
The RC300AU is equipped with thermostat functions
which can automatically control the temperature in
the room in which it is installed. The control is only for
use with the Hearth & Home Technologies IntelliFire
Plus™ system (IPI). The AUX300CE module is rated for
220/240VAC, 50-60 Hz, and is required for operation of
this remote control device.
Installation Precautions
The installation of this remote control must be performed
by a qualified service technician. This remote control is
tested and safe when installed in accordance with this in-
stallation manual. Do not install any components that may
be damaged.
Do not modify, disassemble, or substitute any of the com-
ponents included with this kit. Installation of this unit must
be done by a qualified service technician.
Placement of this remote control may affect performance.
An assessment of the space should be done prior to in-
stallation for optimum performance.
Determine Location
Determine the location for the remote control. The selected
location should be in the same space as the gas fireplace.
Never place this unit in a separate room. The remote control
must be placed within 30 ft. (9.14 m) of the fireplace but
should not be exposed to extreme heat.
The RC300AU is approved for interior installation and
should not be used in exterior applications.
• Keep remote control out of reach of children.
FCC Requirements
WARNING! Risk of Fire! Changes or modifications to
this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate
the equipment.
16
Heat & Glo • 350X-AU, 550X-AU Owner's Manual • 2279-981 Rev. M • 4/23
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules and EN298 for
multi-functional control. These limits are designed to
provide reasonable protection against harmful inter-
ference in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, could cause harmful interfer-
ence to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be
determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Contact the dealer or an experienced radio TV techni-
cian for help.
Changing Temperature Scale
To change the temperature display between Celsius and
Fahrenheit, remove the battery cover from the back of the
remote control and slide the switch to your desired tem-
perature scale. See Figure 3.7. The screen will automati-
cally change the indicators on the room temperature and
set temperature portion.
Figure 3.7 Temperature Scale
Installation of Remote Control Housing
CAUTION! Risk of Fire! DO NOT install damaged or
modified components Warranty will be voided if dam-
.
aged or modified components are installed.
1. Remove remote control components from packaging.
2. Remove battery cover from the back of the remote by
sliding it down and install 3 AAA batteries.
To prevent unintended operation when not using your fire-
place for an extended period of time (summer months,
vacation, trips, etc):