Autopage Car-Pro CPX-2200 Installation & Operation Manual

SVMASTER -
Car-Pro
By:
Professional Vehicle Security
CPX-2200
INSTALLATION & OPERATIONS
MANUAL
CPX-2200 WIRE DIAGRAM
Car-Pro
CPX-2200
H1: 10 pin main harness
H2: 3-pin sensor harness
H3: 2-pin LED harness
H4: 3-pin door lock harness
H1: 10 PIN HARNESS
1. Blue wire: Instant trigger ground input
10. 2. Violet wire: Positive door trigger input
9.
3. Green wire: Negative door trigger input
4. Yellow wire: To Ignition switch + 12V
5. Red wire: to constant battery +12v
6. Brown wire: Positive output to siren
7. Black wire: Ground to vehicle
8, Orange wire: 200 mA Ground output when arm
9. Red/White wire: Parking light relay power input
10. White wire: Parking light relay output
- http://www.msvmaster.lv
A. TRANSMITTER CODE LEARNING:
Note: This security system will only retain the last 4 remote transmitters programmed. If the
transmitter memory is exceeded, the security system will start deleting transmitters from memory in
chronological order.
1.
2.
3.
4.
5.
Exit: Turn the ignition off, 3 long chirps confirm exit.
oooo B. FEATURE PROGRAMMING
1.
2.
3.
Blue (-) 200mA Unlock
4.
Green (-) 200mA Lock
5.
6.
Number of pressing
button I + II & chirps
12V
Exit: Turn the ignition off, or close the door, 3 long chirps confirm exit.
C. PASSWORD SETUP:
1.
12V 2.
3.
15A Fuse
4.
5.
6.
Note: Default setting of password code from the factory is " 1".
From ignition switch To start solenoid
30
85 87a 86
87
SVMASTER -
PROGRAMMING
Disarm the system.
Open the Door and keep the door open
Turn the ignition key " OFF / ON " 6 times, keep at "ON" position at 6
get 6 chirps to confirm enter transmitter programming.
Within 15 seconds press & hold any button for transmitter code learning, a long chirp confirm
transmitter programmed.
nd rd th
Apply steps 4 – 5 to program 2 , 3 and 4 transmitter.
Disarm the system.
Open the Door and keep the door open.
Turn the ignition key " OFF / ON " 3 times stay in on position. (3 chirps to confirm in
programming mode)
Within 15 seconds press button " I + II " to select the feature which you want to program. See
the features programming table below to select the desired features, which you want to
program. Note the number of siren chirps to confirm the selected feature(s).
Press the button " I " or " II " on the transmitter to enable or disable the specific feature.
Repeat steps 4 - 5 for any other features you wish to program.
Program feature Press button " I "
/ one long chirp
Factory Setting
1 Time for door lock 0.9 sec.
2 Passive Door Lock Disable
3 Ignition lock Enable
4 Anti car-jacking Disable
5 Door Ajar Warning Enable
Disarm the system.
Open the Door and keep the door open
Turn the ignition key " OFF / ON" 9 times for "New Password Pin Code Setting" and keep at
th
"ON" position at 9 time switching.
After 2-second pause, the siren will chirp 9 times to confirm entry.
Within 15 seconds, begin to enter your chosen 1 – 9 digit by pressing and releasing the
transmitter button "I" from 1-9 times
Press button " II " to get out of password setup mode, corresponding to the new password code
report by siren chirp confirmation.
th
time switching, you will
Press button " II "
/ Two long chirps
3.5 sec.
Enable
Disable
Enable
Disable
- http://www.msvmaster.lv