Husqvarna AUTOMOWER 550 Operator's Manual page 27

b) Divide the measured area with the total work
area.
c) Convert the result to percentage.
d) Move the horizontal bar to set the distance
from the charging station.
7. Select Save .
The default settings lets the product follow the guide
wire 300 m / 980 ft. in 20% of the times it leaves the
charging station. If the guide wire is less than 300 m /
980 ft. the product will follow it to the point where the
guide wire is connected to the boundary wire.
To measure the distance from the charging station
1. Put the product in the charging station.
Settings > Installation > Lawn coverage in
2. Select
the app.
3. Move the horizontal bar to set the distance to the
charging station to maximum.
Test: Area 1-5 setup .
4. Select
5. Follow the instructions in the app to start the test.
6. Push the STOP button when the product is at the
distance you select to measure. The distance
shows in the app.
To do a test of the Lawn Coverage function
1. Put the product in the charging station.
Settings > Installation > Lawn coverage in
2. Select
the app.
3. Select Test: Area 1-5 setup .
4. Follow the instructions in the app to start the test.
5. The product will run to the starting point for this
area.
3.11.3.3 Corridor width
The boundary wire corridor is the area adjacent to the
boundary wire and the guide corridor is the area
adjacent to the guide wire. The product uses the
corridors to find the charging station. When the product
moves in the direction of the charging station, it always
moves to the left of the guide wire.
The corridor width is adjusted automatically. Only some
times it is necessary to enter manual settings. The
1439 - 007 - 07.01.2021
corridor width can be set between 0-9. If guide corridor
width is set to 0, the product straddles the guide wire.
The factory setting is 6 for the boundary wire and 9 for
the guide wire.
To set the corridor width
Settings > Installation > Corridor width in
1. Select
the app.
2. Move the horizontal bar to set the width.
Save .
3. Select
Note:
Make the corridor width as wide as possible for
a minimum risk of lines in the lawn.
3.11.3.4 Exit angles
In the factory setting the product moves out from the
charging station in a direction in the 90°-270° exit sector.
Change the exit angles to make it easier for the product
to find the work areas. If the charging station is put in a
passage, 2 exit angles, for example 70°-110° and
250°-290°, can be used. When 2 exit angles are used, it
is necessary to set how frequently the product must
move out from the charging station in Sector 1. Use the
Proportion function to set how frequently the product
must use each sector. For example 75% means that the
product moves out from the charging station in Sector 1
on 75% of the times and 25% of the times in Sector 2.
To set the exit angles
Settings > Installation > Exit angles in the
1. Select
app.
2. Move the horizontal bar to set the angles in
degrees for the sectors, and proportion as a
percentage.
Save .
3. Select
3.11.3.5 Reversing distance
The reversing distance makes the product move in
reverse for a set distance, before the product starts to
cut the lawn. The factory setting is 60 cm / 24 ft.
To set the reversing distance
Settings > Installation > Reversing distance
1. Select
in the app.
2. Move the horizontal bar to set the distance.
Save .
3. Select
3.11.3.6 Drive Past Wire
The front of the product always moves past the
boundary wire by a specified distance before the product
moves back into the work area. The factory setting for
Drive Past Wire function function is 31 cm / 12 in.
the
You can select a distance of 20-50 cm / 8-20 in.
Note:
With the factory setting the product will cut 11
cm / 4 in. past the wire.
Installation - 27