Table of Contents
Advertisement
Safety, performance, and dependability have been given
top priority in the design of your mitre saw.
INTENDED USE
The mitre saw is intended for sawing solid and bonded
wood, materials similar to wood, with or without glued
veneer and plastics.
The saw is intended to be used only by adult operators who
have read the instruction manual and understand the risks
and hazards.
whole machine may move during cutting operations, which
increases the possibility of serious personal injury.
The mitre saw is designed make bevel and mitre cuts. The
capacities for the various cuts are provided in the mitre saw
ambient lighting and adequate ventilation.
The mitre saw is intended for consumer use and should
only be used as described above and is not intended for
any other purpose.
GENERAL SAFETY WARNINGS
WARNING
When using electric tools, basic safety precautions
electric shock and personal injury. Read all these
instructions before attempting to operate this product
and save these instructions.
Keep work area clear. Cluttered areas and benches
invite injuries.
Consider work area environment.
tools to rain. Do not use tools in damp or wet locations.
Keep work area well lit. Do not use tools in the presence
of flammable liquids or gases.
Guard against electric shock. Avoid body contact with
earthed or grounded surfaces (e.g., pipes, radiators,
ranges, refrigerators).
Keep other persons away. Do not let persons,
especially children, be involved in the work, touch the
the work area.
Store idle tools. When not in use, tools should be
stored in a dry locked-up place, out of reach of children.
Do not force the tool. It will do the job better and safer
at the rate for which it was intended.
Use the right tool. Do not force small tools to do the
job of a heavy duty tool. Do not use tools for purposes
cut tree limbs or logs.
Dress properly. Do not wear loose clothing or
jewellery, they can be caught in moving parts. Non-
skid footwear is recommended when working outdoors.
Wear protective hair covering to contain long hair.
Use protective equipment. Use safety glasses. Use
face or dust mask if working operations create dust.
Connect dust extraction equipment. If the tool is
collecting equipment, ensure these are connected and
properly used.
Do not abuse the cord. Never yank the cord to
disconnect it from the socket. Keep the cord away from
heat, oil and sharp edges.
Secure work. Where possible, use clamps or a vice to
hold the work. It is safer than using your hand.
Do not overreach. Keep proper footing and balance
at all times.
Maintain tools with care. Keep cutting tools sharp
and clean for better and safer performance. Follow
instruction for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have
them repaired by an authorized service facility. Inspect
Keep handles dry, clean and free from oil and grease.
Disconnect tools. When not in use, before servicing
and when changing accessories such as blades, bits
and cutters, disconnect tools from the power supply.
Remove adjusting keys and wrenches. Form the
habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning it
on.
Avoid unintentional starting. Ensure switch is in "off"
position when plugging in.
Use outdoor extension leads. When the tool is used
use and so marked.
Stay alert. Watch what you are doing, use common
sense and do not operate the tool when you are tired.
Check damaged parts. Before further use of tool, it
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting and any other
conditions that may affect its operation. A guard or
other part that is damaged should be properly repaired
or replaced by an authorized service centre unless
otherwise indicated in this instruction manual. Have
defective switches replaced by an authorized service
centre. Do not use the tool if the switch does not
turn it on and off.
Warning. The use of any accessory or attachment
other than the one recommended in this instruction
manual may present a risk of personal injury.
Have your tool repaired by a qualified person. This
electric tool complies with the relevant safety rules.
Repairs should only be carried out by qualified persons
using original spare parts otherwise this may result in
considerable danger to the user.
Safety
1
Advertisement
Table of Contents
