Related Manuals for Ryobi EMS-1422L
Summary of Contents for Ryobi EMS-1422L
- Page 1 EMS-1422L 210mm COMPOUND MITRE SAW OWNER'S OPERATING MANUAL EMS-1422Lmanual (SAA).indd A1 EMS-1422Lmanual (SAA).indd A1 1/8/08 10:53:03 AM 1/8/08 10:53:03 AM...
- Page 2 Fig. 2 Fig. 1 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 EMS-1422Lmanual (SAA).indd A2 EMS-1422Lmanual (SAA).indd A2 1/8/08 10:53:09 AM 1/8/08 10:53:09 AM...
- Page 3 Fig. 8 Fig. 9 Fig. 11 Fig. 10 Fig. 13 Fig. 12 Fig. 15 Fig. 14 EMS-1422Lmanual (SAA).indd A3 EMS-1422Lmanual (SAA).indd A3 1/8/08 10:53:14 AM 1/8/08 10:53:14 AM...
- Page 4 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 21 Fig. 20 EMS-1422Lmanual (SAA).indd A4 EMS-1422Lmanual (SAA).indd A4 1/8/08 10:53:18 AM 1/8/08 10:53:18 AM...
- Page 5 RIGHT Fig. 22 Fig. 23 WRONG Fig. 24 Fig. 25 EMS-1422Lmanual (SAA).indd A5 EMS-1422Lmanual (SAA).indd A5 1/8/08 10:53:20 AM 1/8/08 10:53:20 AM...
-
Page 6: Rules For Safe Operation
■ DO NOT OVERREACH. RULES FOR SAFE OPERATION Keep proper footing and balance at all times. ■ SWITCH TRIGGER Avoid accidental starting, be sure the switch trigger is WARNING: in the locked or OFF position after use. When using electric tools, basic safety precautions, ■... -
Page 7: Additional Safety Rules
■ Do not slow or stop a blade with a piece of wood. Let ADDITIONAL SAFETY RULES the blade come to rest naturally. If you are interrupted Always remove the plug from the main socket before when operating the saw, complete the process and making any adjustments or maintenance, including switch off before looking up. -
Page 8: Specifications
ADDITIONAL SAFETY RULES DESCRIPTION Fig.1 LASER BEAM SAFETY INSTRUCTIONS HANDLE ■ Do not look into the laser beam. LOWER GUARD SAFETY LOCK ■ Do not point the laser beam at people or animals. LOWER BLADE GUARD ■ Do not use the laser beam on highly reflective LOCK DOWN PIN materials. - Page 9 the lower blade guard downward. KNOW YOUR MITRE SAW INSTALLING THEANTI-TIP (29) ■ SAFETY LOCK (2) Push the safety lock button then squeeze the trigger ■ Insert the Rear Anti-Tip(29) into the hole then use the switch button(17) to power on the saw. Release for screw(a) to fix it.(Fig.10) power off (fig.
-
Page 10: Bevel Cut
■ Place the workpiece flat on the mitre table with one ADJUSTMENT edge securely against the fence. If the board is warped, place the convex side against the fence SQUARING THE BLADE TO THE MITRE TABLE and clamp. If the concave edge of a board is placed ■... -
Page 11: Compound Cut
OPERATING YOUR MITRE SAW TO MAKE A COMPOUND CUT WITH YOUR MITRE ■ Once the handle has been set at the desired angle, ■ Pull out the lock pin and lift the saw arm to its full securely tighten the bevel lock knob (20). height. -
Page 12: Extension Cords
OPERATING YOUR MITRE SAW MANTENANCE WARNING: To avoid serious personal injury, always GENERAL keep your hands outside the no hands zone, at Avoid using solvents when cleaning plastic parts. Most least 75mm from the blade. Never perform a cutting plastics are susceptible to damage from various types operation without holding the workpiece against the fence. - Page 13 EMS-1422Lmanual (SAA).indd Sec1:13 EMS-1422Lmanual (SAA).indd Sec1:13 1/8/08 10:53:30 AM 1/8/08 10:53:30 AM...