Related Manuals for Hunter Barnes Bay
Summary of Contents for Hunter Barnes Bay
- Page 1 Barnes Bay Installation Manual Model: 50992 Matte Silver 50993 Fresh White 59560 Natural Iron Fan weight ±2 lbs: 19.8 lbs (9.0 kg) ©2020 Hunter Fan Co. PG3622 r032720...
- Page 2 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. c.2 - Use only Hunter replacement parts. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 3 1886 Here is what comes in your box: Hunter Pro Tip: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those Do not discard the hardware bags or mix parts from parts.
-
Page 4: Choosing The Right Installation Location
A little more information on Angled Mounting: For optimum performance and appearance, a longer downrod should be used with your Hunter ceiling fan when installing on high or angled ceiling. If your ceiling is angled greater than 34° you will also need an Angled Mounting Kit. -
Page 5: Installing The Ceiling Bracket
You have two options for installation. Pick which one works best for your location. Remove any existing Hunter Pro Tip: bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. The machine screws are the ones that came with your outlet box. -
Page 6: Hanging The Fan
1886 Hanging the Fan DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Progress Check: Your fan should look like this. Note: Fan style may vary. Ceiling Bracket Downrod Hanging Fan Wiring... -
Page 7: Wiring The Fan
If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: Here is how to connect the wires: 4 Wire Nuts (these are in the... -
Page 8: Installing The Canopy
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. Canopy Screw Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Put the blade washers, found in the hardware bag, onto the blade screws, found in the hardware bag. - Page 9 1886 Preparing the Light Fixture Follow these steps to prepare the light fixture for installation. KEEP Fixture Screw Red Flag Repeat x2 Remove the pre-installed fixture screw Carefully remove the (with washer) and red flag from the light Remove and discard the light kit assembly from kit assembly.
-
Page 10: Installing The Light Fixture
1886 Installing the Light Fixture 3 of 4 Fixture Screw Empty Post (With Washer) Fixture Screw Connect plug to the light kit assembly. Partially install three fixture screws Make sure to line up the colored with washers, found in the markings on the connectors and that the hardware bag, into the posts as shown, connectors latch. - Page 11 1886 Installing the Pull Chains Feed the pull chains from the fan switch The fan pull chain controls and the light switch down through the the speed: from high to off. holes in the light kit assembly as shown. Attach the pull chain pendants to the light and fan pull chains.
-
Page 12: Troubleshooting
• Use the provided balancing kit and instructions to balance the fan. Noisy Operation • Make sure the blades are properly installed. Hunter Pro Tip: • Check to see if any of the blades are cracked. If so, Cleaning the Fan replace all of the blades. -
Page 13: Limited Lifetime Warranty
Hunter instructions, accidental damage caused by the fan owner or related parties, Please do not ship your fan or any fan parts to Hunter. Delivery will be refused. modifications to the fan, improper or incorrectly performed maintenance or repair,...