Maytag MLG21PD Installation Instructions Manual page 30

ELECTRONIC CONTROL SETUP INSTRUCTIONS
WARM START (after power failure) – A few seconds after power
is restored, if a cycle was in progress at the time of the power
failure, "RESELECT CYCLE" will flash in the display, indicating
the need for a key press to restart washer or dryer.
WASHER DOOR LOCK – Prior to beginning a cycle, there is a
door lock routine of lock/unlock/relock, and then cycle begins.
The door will remain locked until the end of a cycle or
approximately 2 minutes after a power interruption.
PRICING – After the door is opened and then closed following
the completion of a cycle, the display indicates the cycle price
(unless set for free operation, where the display will flash "SELECT
CYCLE"). As coins are dropped or debit inputs arrive, the display
will change to lead the user through the initiation of a cycle.
There are four (4) types of dryer pricing:
Fixed "Vend" Pricing
A dryer setup for "Fixed Cycle" operation can only accept
additional time accumulated by increments equal to the length of a
complete dry cycle. A maximum of 99 minutes may be purchased;
no additional credit is given for coins dropped with 99 minutes in
the display.
Accumulator Pricing
If the price is set to one coin 1, then accumulator pricing is
in effect. Cycle time can be purchased one coin at a time
(PD models) up to the maximum time of 99 minutes.
Fixed Cycle With Top Off Pricing
A dryer set to offer "Top Off" capability will allow time to be added
to an existing dry cycle in increments equal to the number of
minutes of dry time per coin (coin 1), up to 99 minutes, regardless
of the cost required to start the dryer. No credit is given for coins
or debit inputs entered when the control is displaying 99 minutes.
PN Models: In Enhanced Debit Mode, the top off price can be set
independently (see VALUE OF COIN 2), and the top off time is
calculated according to the following equation:
top off price
top off time =
full cycle price
Penny increment offset is not applied to top off purchases.
FREE CYCLES – This is established by setting the cycle price
to zero. When this happens, "SELECT CYCLE" will appear
rather than a cycle price. Any cycle started as a free cycle
will automatically terminate when the door is opened.
30
x full cycle length
DEBIT CARD READY – This washer/dryer is debit card ready.
It will accept a variety of debit card systems, but does NOT
come with a debit card reader. Refer to the debit card reader
manufacturer for proper washer/dryer setup. In models converted
to a Generation 1 debit card system, debit pulses represent the
equivalent of one coin (coin 1).
Control Set-up Procedures
IMPORTANT: Read all instructions before operating.
PD/PN Models: Insert service switch key and turn
counterclockwise.
PN Models: Once a Generation 2 debit card reader is installed
(according to the reader manufacturer's instructions), the set-up
modes can only be changed by inserting a set-up card (supplied
by the reader manufacturer) into the card slot. Inserting the service
switch key and turning will only allow access to the service mode.
The washer/dryer is now in the set-up mode. The lower fabric
setting buttons and the lower portion of the display are used to set
up the digital control for the washer. The upper three fabric setting
buttons and the upper portion of the display are used to set up the
controls for the dryer.
The display can contain 4 numbers and/or letters and a decimal
point on both the top and bottom display portions. These are used
to indicate the set-up codes and related code values available for
use in programming the washer/dryer.
How to Use the Buttons to Program the Controls
1. The lower-left (BRIGHTS) button is used to adjust the values
associated with washer set-up codes and the upper-left
(WHITES & COLORS) button is for the dryer. Pressing the
button will change the value by increments. Rapid adjustment
is possible by holding the button down.
2. The lower-middle (DELICATES & KNITS) button will advance
through the set-up codes. Pressing the button will advance
both the washer and dryer to the next available set-up code.
Some set-up codes are washer- or dryer-specific and will not be
displayed on both the washer and dryer portions of the display.
Holding down the lower-middle (DELICATES & KNITS) button
will automatically advance through the set-up codes
at a rate faster than 1 per second.
3. The lower-right (QUICK CYCLE) button is used to select or
deselect washer options; upper-right (STOP/PAUSE) is used
for dryer option selection or deselection.