Page 2
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be reproduced,translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission.
Usage Notice Warning - To prevent the risk of fi re or shock hazards, do not expose this product to rain or moisture. Warning - Please do not open or disassemble the product as this may cause electric shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.
Introduction About PA1575R The PA1575R is All-in-One Touch computer model. It has a 15" fl at panel screen with an active matrix, thin-fi lm transistor (TFT) liquid crystal display (LCD). The PA1575R incorporates the Mobile Intel® 910GMLE/915GME Chipset, consisting of the Intel®...
Page 6
• Removable base for fl exible mounting solutions. • 5-wire resistive touch screen with USB controller • Built-in speakers-1W x 2 Touch Screen for PA1575RXP / PA1575RWP • Analog 5-wire resistive touch screen for fi nger and stylus input • Surface: Anti-glare treatment •...
Kensington Security Slot The computer can be secured to your desk or any other fi xed object with Kensington lock security products. The Kensington lock is not included.
VESA Mount Your Computer This computer conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defi nes a physical mounting interface for fl at panel computers, and corresponding with the standard mounting devices of fl at panel computer, such as wall and table arms.
Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can hookup the cables to associated connector. 1. Remove the stand back cover by pulling in the direction of the arrow. 2.
User Controls Side Panel Controls Menu off status Menu appear Brightness Mute Enter/Select sub-item function Power On/Off Icon key Name Menu Down Enter Power Menu on status Menu disappear/ return to main item Main item select up/ Adjust up Main item select down/ Adjust down...
Initial Turn-On The initial setup of the operating system takes approximately 5-10 minutes. Additional time may be needed depending on touch computer hardware confi guration and connected devices. To setup the Windows OS for the touch computer, turn on the touch computer and follow the instructions on the screen.
Page 15
Step 2. Press "Next" Step 3. Read agreement and press " I accept this agreement" and "Next".
Page 16
Step 4. Language Selection, Press "Next" Click Customize. The Regional and Language window shown below will appear. Step 5. Type your full name, organization and press "Next"...
Page 17
Step 6. Type product key and press "Next" Please fi nd the "Certifi cate of Authenticity" license label on the back-cover.
Page 18
Step 7. Setup your computer name, administrator password and press "Next" Step 8. Date and Time Settings, Setup your computer date and time and press "Next"...
Page 19
Step 9. Choose typical or custom setting and press "Next" Step 10. Choose applicable option ▎ ▼...
WEPOS Initial On Steps Step 1. Boot Computer Step 2. Enter log on screen, the default User name is showed "Administrator"...
Page 22
Step 3. Please type the default Password=”~tpc152~” ( Note: Please enter Start\Control Panel\ User Accounts to change password after logging on windows system at fi rst time.) Step 4. Finish...
The touch computer can be pre-installed with several different hardware options. To test an optional device that is installed on the touch computer, follow the instructions below. NOTE: Testing icons are located on the desktop. Testing of a particular device can only be done after the device is properly installed.
Recovering the Operating System If the touch computer’s operating system and software needs to be recovered, insert the included recovery disk into an external DVD-ROM (sold separately) and reboot the touch computer. Follow the on-screen instructions to complete recovery. NOTE: All data will be deleted during the recovery process. User must back up fi les prior to recovering the operating system.
Page 26
▎ ▼ Press any key to continue Step 4. ▎ ▼...
Page 27
Press any key to continue Step 5. ▎ ▼ ▎ ▼...
Page 28
Press "Next" Step 6. Read agreement and press "I accept this agreement" and "Next". Step 7.
Page 29
Press "Next" Step 8. Type your full name, organization and press "Next" Step 9.
Page 30
Type product key and press "Next" Step 10. Please fi nd the "Certifi cate of Authenticity" license label on the back-cover.
Page 31
Setup your computer name, administrator password and press "Next" Step 11. Setup your computer date and time and press "Next" Step 12. Choose typical or custom setting and press "Next" Step 13.
Page 32
Choose applicable option Step 14. Press "Finish" Step 15. Finish and launch windows system Step 16.
B. For WEPOS To recover your pre-installed software using the recovery CD, do as follows: From the Start menu, restart your computer. Step 1. Insert "Recovery CD" in CD-ROM to start-up sequence. Step 2. Press any key to boot from CD Step 3.
Page 36
The default User name is showed “Administrator”, please type the “~tpc152~” Step 6. in password column and press OK. ( Note: Please enter Start\Control Panel\ User Accounts to change password after logging on windows system at fi rst time.) Finish and launch Windows System. Step 7.
Insert the included Touchscreen disk into an external DVD-ROM (sold Step 1. separately) Select the monitor size 15” and then model name PA1575R. Step 2. Click on the “Load Driver” button that appears to the right of the model name.
Display Specifi cations Model LCD Display Display Size Pixel Pitch Display Mode Native Display Color Plug & Play PA1575RXP / PA1575RWP 15" TFT Active Matrix Panel 304.1(H) x 228.1(V) mm 0.297(H) x 0.297(V) mm VGA 720 x 400 (70 Hz) VGA 640 x 480 (60 Hz) SVGA 800 x 600 (60 Hz) XGA 1024 x 768 (60 Hz)
Power Supply Specifi cations The touch computer shall be powered by 12VDC from a universal type power supply brick with the following characteristics: Input voltage Input frequency Output voltage Output line and load regulation Output current Environmental Specifi cations Temperature Ranges Operating Temperature (Independent of altitude) Non-Operating Temperature (Independent of altitude) Humidity...
Touch Computer Specifi cations Intel Celeron M 1.0GHz CPU w/400MHz Front-Side Bus Processor 1GB DDR2 RAM standard. Up to 2.0GB Intel 910 GMLE Northbridge Intel ICH6M Southbridge Intel GMA 900 Up to 128MB shared w/ DVMT Video Microsoft Windows XP Professional Embedded Operating systems Microsoft Windows Embedded for Point of Service (WEPOS) 3 x USB 2.0 ports...
Page 41
One-watt/channel speakers in display head Speakers (internal) Side: Power and user controls with lockout function for public use User controls 75 mm VESA mount Mounting options Removable base Fanless Energy save mode (less than 2 watts) Other features Touchscreen sealed to bezel and LCD Security lock receptacle Peripheral Options May vary...
Page 42
RJ45 LAN connector Pin Defi nition Power Input Pin Defi nition Cash Drawer Port Signal Defi nition and Control Pin # 1 2 3 4 5 6 Front View Signal Name Pin # Signal Name Pin # +12V Ground Ground +12V Signal Name Frame Ground...
How to Use the OSD Menus 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the six functions in the main menu. 2. Choose the adjustment items by pressing the “Enter ” button. 3.
On-Screen Display Menus Main OSD Menu: ITEM Adjusts the maximum luminance level of the computer. CONTRAST Adjusts the backlight of the computer. BRIGHTNESS Adjusts the OSD menu screen position left or right. OSD LEFT/RIGHT Adjusts the OSD menu screen position up or down. OSD UP/DOWN Adjusts the time for OSD auto-disappear after menu on.
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. ► Check that all the I/O and power connectors are correctly and well connected described in the "Installation"...
Product Registration and Technical Support Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefi ts of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www.planar.com/support/product_registration.html.