Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
This Roof Curb is NRCA approved and is constructed of 14 gauge galvanized steel with a full perimeter 2" X 4"
wood nailer strip. The curb is shipped with the following parts.
026-36345-002 14" HIGH
A
1
Side Panel Right, 78 1/2 x 14
B
1
Side Panel Left, 78 1/2 x 14
C
1
Side Panel Right, 78 1/2 x 14
D
1
Side Panel Left, 78 1/2 x 14
E
8
Side Panels, 71.75 x 14
F
3
End Panels, 83 x 14
G
3
Brace Panels, 83 x 14
H
1
End Panel, 83 x 11
J
1
Supply Panel, 43 x 14
K
4
Support Rails, 83 x 3
L
5
Condenser Panels
M
10
Splice Channels
N
4
Condenser Panel Flashings
P
1
Hardware Package
(100) .375-16 x 1.00 Hex Bolt w/ Nuts
(100) .375 Helical Lock washers
(100) .375 Flat Washers
(157) 25-14 x .75 Screw Tapping
(Washer Head Seal Tight)
(126 Ft) 3/4 x 1 1/4 Foam Gasket
(100 Ft) 3/4 x 1/8 Tacky Tape
ROOF CURB
70–85 TON FULL PERIMETER
MODEL # 026-36345-002 / 026-36345-102
PACKAGED ROOFTOP UNITS
NEW RELEASE
026-36345-102 24" HIGH
A
1
Side Panel Right, 78 1/2 x 24
B
1
Side Panel Left, 78 1/2 x 24
C
1
Side Panel Right, 78 1/2 x 24
D
1
Side Panel Left, 78 1/2 x 24
E
8
Side Panels, 71.75 x 24
F
3
End Panels, 83 x 24
G
3
Brace Panels, 83 x 24
H
1
End Panel, 83 x 21
J
1
Supply Panel, 43 x 24
K
4
Support Rails, 83 x 3
L
5
Condenser Panels
M
10
Splice Channels
N
4
Condenser Panel Flashings
P
1
Hardware Package
(168) .375-16 x 1.00 Hex Bolt w/ Nuts
(168) .375 Helical Lock washers
(168) .375 Flat Washers
(157) 25-14 x .75 Screw Tapping
(Washer Head Seal Tight)
(126 Ft) 3/4 x 1 1/4 Foam Gasket
(100 Ft) 3/4 x 1/8 Tacky Tape
Form YRK2-N1 (319)
Advertisement
Related Manuals for York 026-36345-002
Summary of Contents for York 026-36345-002
- Page 1 ROOF CURB 70–85 TON FULL PERIMETER MODEL # 026-36345-002 / 026-36345-102 This Roof Curb is NRCA approved and is constructed of 14 gauge galvanized steel with a full perimeter 2" X 4" wood nailer strip. The curb is shipped with the following parts.
-
Page 2: Installation
(E). Make sure the corners are flush and square as shown in Figure 3. Place the curb in the proper location. M (2 TYP) Make sure the curb section is “IN SQUARE.” SAME PIECE SHOWN IN NEXT FIGURE FIGURE 3 - LD08551 YORK... - Page 3 (D). Attach the Support Rails (K) in place with .25 -14 x 1" screws as shown in Figure 5 Each section of the curb is to be connect- ed with the provided splice channels as shown in illustrations. YORK...
- Page 4 14. Install the Condenser Panels (L) in the order as shown in Figures 7 and 8. As each panel is in- stalled in place, attach the lower edge of the Con- denser Panels (L) with .25-14 x 1" screws. YORK...
- Page 5 15. Install the sloped Condenser Panel Flashing (N) 16. Install 3/4 x 1-1/4" foam gasket on top of all curb over the curb 2" edge as shown in Figure 9. surfaces. " " Refer to Figure 10 FIGURE 9 - LD08557 YORK...
- Page 6 FOAM GASKET WOOD NAILER CURB FRAME COUNTER FLASH ING (FIELD SUP PLIED) ROOF ING FELT (FIELD SUP PLIED) RIGID IN SU LA TION (FIELD SUP PLIED) FLAT SIDE FLANGE SIDE CANT STRIP (FIELD SUP PLIED) FIGURE 11 - LD08559 YORK...
- Page 7 ISSUE DATE: 03/18/2019 All dimensions are critical to ensure prop- er fit of the unit to the curb. All dimen- sions are from the "Flat Side" of the curb panels with the exception of "Outside" curb dimensions. FIGURE 12 - LD08560 YORK...
- Page 8 YORK IS A REGISTERED TRADEMARK OF JOHNSON CONTROLS ® © 2019 Johnson Controls | 100 JCI Way, York, Pennsylvania USA 17406-8469 | www.york.com Subject to change without notice. | Form YRK2-N1 (319) | New Release | All rights reserved.