Danfoss iC7 Series Installation Manual
In-back/out-top cooling kit for fa09-fa10, frequency converters
Hide thumbs
Also See for iC7 Series:
- Application manual (382 pages) ,
- Operating manual (64 pages) ,
- Installation manual (36 pages)
Table of Contents
Advertisement
Quick Links
Installation Guide
In-back/Out-top Cooling Kit for FA09-FA10
iC7 Series Frequency Converters
1 Overview
1.1 Description
The in-back/out-top cooling kit fits FA09 and FA10 frequency converters mounted in Rittal TS8 cabinets. When the kit is installed, air
flows into the lower back duct and out through the top of the drive. See
1
2
Illustration 1: Direction of Airflow with the Kit Installed
1
Top duct (exhaust)
2
Cooling back channel
1.2 Kit Numbers
Use these instructions with the following kits.
Table 1: Kit Numbers for In-back/Out-top Cooling Kits
Kit number
Kit description
176F4042
In-back/out-top cooling kit for FA09 frequency converters
176F4043
In-back/out-top cooling kit for FA10 frequency converters
Danfoss A/S © 2022.03
Illustration
1.
3
4
3
Airflow direction
4
Lower duct (intake)
AN371942666355en-000101 / 136R0250 | 1
Advertisement
Table of Contents
Related Manuals for Danfoss iC7 Series
Summary of Contents for Danfoss iC7 Series
- Page 1 Installation Guide In-back/Out-top Cooling Kit for FA09-FA10 iC7 Series Frequency Converters 1 Overview 1.1 Description The in-back/out-top cooling kit fits FA09 and FA10 frequency converters mounted in Rittal TS8 cabinets. When the kit is installed, air flows into the lower back duct and out through the top of the drive. See...
-
Page 2: Items Supplied
Top gasket, lower duct Grill gasket, lower duct Back grill, lower duct Side gasket, lower duct Base cover, lower duct Base gasket, lower duct M10x30 screw M5x10 taptite screw M5x12 screw 2 | Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250... -
Page 3: Installation
N O T I C E ELECTROSTATIC DISCHARGE Electrostatic discharge can damage components. Ensure discharge before touching internal frequency converter components, for example by touching a grounded, conduc- tive surface or by wearing a grounded armband. Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250 | 3... -
Page 4: Installation Overview
This kit contains self-adhesive gaskets to ensure a proper seal between metal parts. Before affixing a gasket, check that the part matches the gasket and that no holes are covered. Illustration 2: Overview of In-back/Out-top; Cooling Kit 4 | Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250... - Page 5 The holes must match the holes in the upper flange of the top duct. 223 (8.8) 191 (7.5) 6x Ø 4 (0.2) 80 (3.1) 95 (3.7) 95 (3.7) 3 (0.1) 14 (0.6) Illustration 3: FA09 Rittal Cabinet Top Plate Template Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250 | 5...
- Page 6 Insert 4 M10 pem nuts (not supplied) in the mounting holes. Cut out the vent opening in the mounting plate using the dimensions in the template. The opening must match the opening in the lower duct. 6 | Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250...
- Page 7 877 (34.5) 2x Ø 8 (0.3) Drive Mounting Holes 200 (7.9) 140 (5.5) 177 (7.0) 4x Ø 5 (0.2) 214 (8.4) 228 (9.0) Illustration 5: FA09 Mounting Plate Template for In-back/Out-top Cooling Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250 | 7...
- Page 8 The FA09 requires 6 holes around the vent opening, and the FA10 requires 8 holes around the opening. The holes must align with the holes in the outer flanges of the duct. 8 | Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250...
- Page 9 In-back/Out-top Cooling Kit for FA09-FA10 Installation Guide Installation Example 10 (0.4) 236 (9.3) 215 (8.5) 6x Ø 7 (0.3) 266 (10.5) Illustration 7: FA09 Cabinet Back Plate Template for In-back/Out-top Cooling Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250 | 9...
-
Page 10: Mounting The Frequency Converter
Make sure that the screws are secure. The base of the frequency converter rests on the screws. Slightly lean the top of the frequency converter forward and set the notches in the base onto the 2 screws. 10 | Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250... - Page 11 Secure the top of the frequency converter using 2 M10x30 screws. Torque all fasteners to 19 Nm (170 in-lb). Example Illustration 9: Installation of the Frequency Converter in the Cabinet Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250 | 11...
- Page 12 With the rubber seal in place, carefully slide the inner sleeve of the duct into the outer sleeve. Illustration 10: Assembly of Telescopic Ducts 12 | Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250...
- Page 13 Align the holes in the side gaskets with the holes in the left and right sides of the back opening of the duct frame. Place the grill over the left and right gaskets, with the threaded studs in the grill going through the middle holes in the gasket and into the duct frame. Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250 | 13...
- Page 14 2.10 Installing the Lower Duct To attach the lower duct to the frequency converter, use the following steps. Procedure Place the strip gasket over the 2 slots at the bottom back of the frequency converter. 14 | Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250...
- Page 15 Holes for attaching duct Top flange of duct Lower duct Front of duct 2.11 Installing the Back Vent To install the back vent, use the following steps. Refer to Illustration Procedure Danfoss A/S © 2022.03 AN371942666355en-000101 / 136R0250 | 15...
- Page 16 Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to form, fit or function of the product.