Danfoss iC7 Series Installation Manual
Tall pedestal kit for fk11/fb11 and fk12/fb12, frequency converters
Hide thumbs
Also See for iC7 Series:
- Application manual (382 pages) ,
- Operating manual (64 pages) ,
- Installation manual (36 pages)
Advertisement
Quick Links
Installation Guide
Tall Pedestal Kit for FK11/FB11 and FK12/FB12
iC7 Series Frequency Converters
1 Overview
1.1 Description
The pedestal kit contains all parts required to install the tall pedestal for FK11/FB11 and FK12/FB12 frequency converters. The ped-
estal is 400 mm (15.7 in) and replaces the standard 200 mm (7.9 in) pedestal that ships with the frequency converter. A pedestal and
cable entry plate are required for proper operation of the frequency converter. The pedestal features a front grill to allow proper
airflow for cooling. Reuse the cable entry plate that ships with the frequency converter to maintain the IP21/Type 1 or IP54/Type 12
protection rating.
1.2 Kit Numbers
Use these instructions with the following kits.
Table 1: Tall Pedestal Kits (400 mm)
Number
Kit Description
176F4044
Pedestal kit for FK11/FB11 frequency converters
176F4037
Pedestal kit for FK12/FB12 frequency converters
1.3 Items Supplied
The following parts are contained in the kit.
Table 2: Items Supplied in Tall Pedestal Kits
Item
Pedestal
Front panel
Front top bracket
Front bottom bracket
Locking brackets
M10x22 screw
M8 hex nut
M5x14 countersunk screw
M10 nylon-insert lock nut
Danfoss A/S © 2022.03
Quantity
1
1
1
1
2
6
4
6
2
AN361529835714en-000101 / 136R0257 | 1
Advertisement
Related Manuals for Danfoss iC7 Series
Summary of Contents for Danfoss iC7 Series
- Page 1 Installation Guide Tall Pedestal Kit for FK11/FB11 and FK12/FB12 iC7 Series Frequency Converters 1 Overview 1.1 Description The pedestal kit contains all parts required to install the tall pedestal for FK11/FB11 and FK12/FB12 frequency converters. The ped- estal is 400 mm (15.7 in) and replaces the standard 200 mm (7.9 in) pedestal that ships with the frequency converter. A pedestal and cable entry plate are required for proper operation of the frequency converter.
-
Page 2: Installation
N O T I C E QUALIFIED PERSONNEL Only qualified, Danfoss authorized personnel are allowed to install the parts described in these installation instructions. Disassembly and reassembly of the frequency converter must be done in accordance with the service guide. - Page 3 2.2 Overview of Pedestal Installation Illustration 1: Pedestal Kit Overview Locking bracket M5x14 countersunk screws M10 nylon-insert lock nut Front panel M10x22 screws Pedestal M8 nut Pedestal cutout Front top bracket Front bottom bracket Danfoss A/S © 2022.03 AN361529835714en-000101 / 136R0257 | 3...
- Page 4 Slide the 2 bolts in the rear of the pedestal into the 2 slotted holes in the rear of the cabinet. Position the frequency converter by adjusting the rear bolts up or down. Loosely secure the frequency converter with 2 M10 nylon-insert lock nuts and locking brackets. Illustration 4 | Danfoss A/S © 2022.03 AN361529835714en-000101 / 136R0257...
- Page 5 Torque each fastener to 19 Nm (169 in-lb). Illustration 3: Pedestal-to-Cabinet Back Mounting Points Cabinet M10 nylon insert lock nut Pedestal Locking bracket Bolt at rear of pedestal Slotted hole in cabinet Illustration 4: Pedestal-to-Cabinet Front Mounting Points Danfoss A/S © 2022.03 AN361529835714en-000101 / 136R0257 | 5...
- Page 6 Fasten the front plate to the pedestal with 6 M5x14 countersunk screws. Illustration 5: Cable Entry Plate Installation Cable entry plate Slot in pedestal Cable entry hole Front cover M5 nut M5 countersunk screw 6 | Danfoss A/S © 2022.03 AN361529835714en-000101 / 136R0257...
- Page 7 Tall Pedestal Kit for FK11/FB11 and FK12/FB12 Installation Guide Installation Danfoss A/S © 2022.03 AN361529835714en-000101 / 136R0257 | 7...
- Page 8 Danfoss reserves the right to alter its products without notice. This also applies to products ordered but not delivered provided that such alterations can be made without changes to form, fit or function of the product.