Related Manuals for WAGNER CONTROL PRO 170
Summary of Contents for WAGNER CONTROL PRO 170
- Page 1 Model 150 Model 170 Model 190 Control pro ™ Owner‘s manual • GuIDe D‘uTIlIsaTIOn • MANUAL DEL PROPIETARIO READ ThIs MANUAL fOR cOMPLETE INsTRUcTIONs fRANÇAIs - P. 24 EsPAÑOL - P. 48 wagner-group.com 0917 • Form No. 0580055D...
- Page 2 Grounding Pin Notes give important information which Cover for grounded outlet box should be given special attention. When the sprayer is used with a generator or uncontrolled line voltage, the use of Wagner’s “Line Surge Protector” (P/N 800-935) Attention recommended.
- Page 3 Inspect hose before each use. Replace • Keep area clean and free of paint or solvent containers, any damaged hoses or parts. Only use Wagner original- rags, and other flammable materials. high-pressure hoses in order to ensure functionality, safety •...
-
Page 4: Table Of Contents
IMportAnt SAFEtY InForMAtIon • • Always engage the trigger lock when not spraying. Verify Do not operate the unit when fatigued or under the the trigger lock is functioning properly. influence of drugs or alcohol. • • Verify that all connections are secure before operating the Do not kink or over-bend the hose. -
Page 5: General Information
15 amp minimum circuit on 100 feet 115 VAC, 60 Hz current generator power 5000 Watt requirement Wagner accessory extension cords recommended: (disable idle-down feature) P/N 0090241 20 foot extension cord Overheating protection This sprayer has a built- in protective device to... -
Page 6: Assembly
ASSEMBlY Do not plug in the power cord until assembly is complete. toolS nEEDED • Two 6” adjustable wrenches Attach the tool box doors to the top of the sprayer as shown. Snap one peg into one of the orifices, and then snap the other peg into the other orifice. - Page 7 ASSEMBlY (ContInUED) The spray gun included with the sprayer will have one of two types of hose restraint: 1) the “C” type where the hose is clamped, or 2) the circular type where the hose gets threaded through a hole in the restraint. When attaching the hose to the spray gun, follow the appropriate steps to properly secure the spray hose.
-
Page 8: Parts And Components
pArtS AnD CoMponEntS 150 / 170 PRIME SPRAY SPRAY PRIME ItEM DESCrIptIon Tool box The Tool Box provides a place for items such as extra spray tips or wrenches. Pressure control knob / The pressure control knob regulates the amount of force the pump uses to push the fluid and can be ON/OFF switch adjusted for desired spray pattern. -
Page 9: Before You Begin
BEForE YoU BEGIn This section contains instructions that will be repeated throughout this manual. Read and understand this section before using the equipment. SprAY GUn trIGGEr loCk Be careful when handling the spray gun so you do not accidently spray yourself. The high pressure paint stream could pierce your skin causing serious injury. -
Page 10: Load Material
loAD MAtErIAl These steps will prime the system and get it ready to spray. YoU wIll nEED • The material you plan to spray • Extension cord • Waste bucket recommendation: It is good practice to perform the steps on this page using water to familiarize yourself with the function of the unit as well as to ensure the unit is set up properly. -
Page 11: Spraying
SprAYInG Follow these steps to deliver spray material from the material container to the spray gun. YoU wIll nEED • Waste bucket • Scrap material / cardboard • Drop cloths to protect floors and furnishings from overspray Make sure the tip guard is removed. Point the spray gun into a separate waste container. -
Page 12: Practice Spraying
prACtICE SprAYInG Prior to spraying, it is important that you are using the spray tip / spray material combination that it suitable for your spraying job. Refer to the chart below for a list of recommendations regarding spray tip size, spray material and pressure settings. - Page 13 prACtICE SprAYInG If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, follow any or all the procedures listed on pages 12-13. If you plan to be away from your spray project for more than one hour, follow the Short Term Storage instructions on page 15.
-
Page 14: Clear The Spray Tip
SprAYInG troUBlEShootInG - ClEAr thE SprAY tIp If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the spray tip could be clogged. Follow the steps below. YoU wIll nEED • Scrap material / cardboard Do not attempt to unclog or clean the tip with your finger. -
Page 15: Clean The Inlet Filter
SprAYInG troUBlEShootInG - ClEAn thE InlEt FIltEr If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the inlet filter could be clogged. Follow the steps below. YoU wIll nEED • Warm, soapy water for latex material •... -
Page 16: Short Term Storage
Short-tErM StorAGE This procedure should be used when taking a short term break or when ending your project for the day. If your break is longer than 16 hours follow cleanup instructions, pages 17-18. YoU wIll nEED • Water • Plastic bag •... -
Page 17: Cleanup
ClEAnUp ClEAnInG notES - rEAD BEForE ClEAnInG Follow these steps whenever cleaning with mineral spirits: • When using latex material, clean sprayer and components • If spraying or cleaning with oil-based materials, the spray with warm, soapy water. For oil based material use gun must be grounded while preparing the spray hose mineral spirits. - Page 18 ClEAnUp - ContInUED Point the spray gun at the side of a waste container. Ground the gun against the side of a metal waste container if flushing with mineral spirits. SPRAY While squeezing the trigger, turn the pressure control knob to ‘2’, and turn the PRIME/SPRAY knob to SPRAY.
-
Page 19: Long Term Storage
lonG tErM StorAGE Follow these steps to prepare your sprayer for long- term storage. YoU wIll nEED • Light household oil / All Guard HOUSEHOLD • Rags • Two adjustable wrenches The suction tube should still be removed from the end of the previous section and the PRIME/SPRAY knob should be in the PRIME position. -
Page 20: Cleaning The Inlet Valve
ClEAnInG thE InlEt vAlvE Cleaning or servicing the inlet valve may be required if the unit has priming problems. Priming problems may be prevented by properly cleaning the sprayer and following the long-term storage steps. YoU wIll nEED • Adjustable wrench or 10 mm allen wrench •... -
Page 21: Cleaning The Outlet Valve
ClEAnInG thE oUtlEt vAlvE Cleaning or servicing the outlet valve may be necessary if spray performance remains poor after following the steps in the Troubleshooting section. Call Technical Service (1-800-328-8251) to order a new outlet valve assembly. YoU wIll nEED •... -
Page 22: Troubleshooting
troUBlEShootInG proBlEM CAUSE SolUtIon A. The sprayer does not turn on. 1. The sprayer is not plugged in. 1. Plug the sprayer in. 2. Pressure control knob is set to OFF. 2. Turn pressure control knob to recommended setting. 3. The sprayer shuts off while under pressure. 3. -
Page 23: Warranty
This warranty does not cover damage resulting from improper use, accidents, user’s negligence or normal wear. This warranty does not cover any defects or damages caused by service or repair performed by anyone other than a Wagner Authorized Service Center. -
Page 24: Parts List
Parts List • Liste de Pièces • Lista de Piezas Main asseMbLy • enseMbLe PrinciPaL • Montaje PrinciPaL 150 / 170 Description Description Descripción 0580389 0580389 --------- Base assembly Ensemble de la base Conjunto de la base --------- --------- 0580175 Handle assembly Ensemble de la poignée Conjunto de la manilla... - Page 25 Parts List • Liste de Pièces • Lista de Piezas sPray gun asseMbLy • PistoLet de PuLvérisation • PistoLa de rociadora replacement parts available by calling customer service On peut obtenir des pièces de rechange en appelant le Service à la clientèle. Los repuestos están disponibles llamanado al servicio a clientes.
- Page 26 Parts List • Liste de Pièces • Lista de Piezas suction set asseMbLy • enseMbLe d’asPiration • conjunto de succiÓn Description Description Descripción ------- ------- ------- Suction tube Tube d’aspiration Tubo de succión 0580487 0580487 0580487 Return tube Tuyau de retour Tubo de retorno 0512390 0512390...
- Page 27 accessories • accessoires • accesorios pArt no. DESCrIptIon DESCrIptIon DESCrIpCIón SprAY GUnS pIStolEtS DE pUlvérISAtIon pIStolAS DE pUlvErIzACIón 0580600 Control Pro spray gun Pistolet de pulvérisation Control Pro Pistola de pulverización de Control Pro 0580601 Control Pro M spray gun Pistolet de pulvérisation Control Pro M Pistola de pulverización de Control Pro M SprAY tIpS AnD ACCESSorIES...
- Page 28 QUEStIonS? BESoIn D’AIDE? call wagner Technical Service at: appelez le service technique wagner 1-800-328-8251 1-800-328-8251 register your product online at: Enregistrement du produit en ligne sur le site : www.wagnerspraytech.com www.wagnerspraytech.com ¿nECESItA AYUDA? Llame wagner Technical Service al: 1-800-328-8251 regístrelo del producto en línea en: www.wagnerspraytech.com...