Specification; Specifications - SMC Networks ISE80 Operation Manual

Specification

■Specifications

Model No.
Rated pressure range
Set pressure range
Withstand pressure
Setting and display resolution
Port material
Fluid
Connection port
Power supply voltage
Current consumption
Protection
Switch output
Max. load current
Max. applied voltage
Residual voltage
Response time
Short circuit protection
Repeatability
Hysteresis mode
Hysteresis
Window comparator mode
Voltage
Output voltage
output
∗2
Output impedance
Analogue
output
Output current
Current
output
∗3
Load impedance
Auto shift input
Display
Display accuracy
Indicator LED
Functions
∗1: If the applied voltage fluctuates around the set value, the hysteresis must be set to more than the fluctuation width. Otherwise,
chattering will occur.
∗2: If analogue voltage output is selected, the analogue current output cannot be selected.
∗3: If analogue current output is selected, the analogue voltage output cannot be selected.
ISE80 ISE80H
(positive pressure) (positive pressure)
-0.1 to 1 MPa -0.1 to 2 MPa
-0.105 to 1.1 MPa -0.105 to 2.2 MPa
2 MPa 4 MPa
0.001 MPa
(1.999 MPa)
0.001 MPa
0.01 MPa
(2.00 to 2.20 MPa)
Pressure sensor: SUS630, Fitting: SUS304
Fluid which has no corrosive effect on SUS630, SUS304
R1/4, NPT1/4, G1/4, URJ1/4, TSJ1/4, Rc1/8
Piping direction: Rear or Bottom
12 to 24 VDC ±10% with voltage ripple or less
Protected against reverse connection
NPN1 output, NPN2 output, PNP1 output, PNP2 output
1 V or less (80 mA load current)
2.5 ms (with anti-chatter function: 20, 100, 500, 1000, 2000 ms selectable)
0.6 to 5 V 0.8 to 5V
±2.5% F.S. ±2.5% F.S.
Linearity: ±1% F.S. Linearity: ±1% F.S.
2.4 to 20 mA 3.2 to 20 mA
±2.5% F.S. ±2.5% F.S.
Linearity: ±1% F.S. Linearity: ±1% F.S.
Max. load impedance: 300 Ω (power supply voltage of 12 V)
Min. load impedance: 50 Ω
Non-voltage input (reed or solid state), Low level 0.4 V or less,
input times 5 ms or more
3 1/2 digits, 7-segment display, dual-colour display (red/green)
±2% F.S. ±1 digit (ambient temperature 25 ±3
OUT1/OUT2: ON when LED is ON (Orange)
Anti-chatter function, Zero clear, Key lock, Auto pre-set,
Display unit selection, Power saving mode, Auto shift
-50-
ZSE80
(vacuum)
0 to –101 kPa
10 to –111 kPa
500 kPa
0.1 kPa
45 mA or less
80 mA
28 V (NPN output)
Provided
±0.2% F.S. ±1 digit
∗1
0 to variable
1 to 5V
±2.5% F.S.
Linearity: ±1% F.S.
Approx. 1 kΩ
4 to 20 mA
±2.5%F.S.
Linearity: ±1% F.S.
: 600 Ω (power supply voltage of 24 V)
ZSE80F
(compound)
-100 to 100 kPa
-110 to 110 kPa
o
C)
No.PS※※-OMM0003-J