Section 5: Program Descriptions; Programming Security Codes; Zone Programming - DSC Power632 PC1565 Installation Manual

Section 5: Program Descriptions

The following section explains the operation of all programma-
ble features and options and provides a summary of all corre-
sponding programming locations.
5.1

Programming Security Codes

There are three codes which can be programmed by the
installer in the Installer's Programming function: the Master
code, the Installer's code, and a Maintenance code. All other
access codes can be programmed through the [*][5] com-
mand (see section 3.5 "[*] Commands" on page 8).
The master code can also be programmed by the user as
access code (40). If the Master Code Not Changeable option
is enabled, the system master code can only be changed by
the installer.
General access codes can arm and disarm the system. When
the Code Required for Bypassing option is enabled, users
will need to enter a valid access code when bypassing zones.
Individual access codes can have the Zone Bypassing
attribute disabled under access code attribute programming
(see section 3.5 "[*] Commands" on page 8).
Installer's Code. . . . . . . . . . . . . . . . . . . . . . . . . Section [006]
Master Code. . . . . . . . . . . . . . . . . . . . . . . . . . . Section [007]
Maintenance Code . . . . . . . . . . . . . . . . . . . . . . Section [008]
Master Code Not Changeable . . . . . . . . . . Section [015]: [6]
Code Required for Bypassing . . . . . . . . . . Section [015]: [5]
NOTE: The Maintenance code is limited to arming and disarm-
ing the system. The Maintenance code cannot use [*][9] to arm
the system, bypass zones, or perform [*][7] command functions.
5.2

Zone Programming

All eight zones are enabled by default. Unused zones should
be disabled in programming section [202].
Section [001] will allow you to select how each of the zones
you use will operate. Each zone requires a two-digit code to
be programmed, which describes the zone definition. Select a
definition from the list below.
In addition, each zone has eight different attributes which may
be programmed in sections [101] to [108] (see section 5.3
"Zone Attributes" on page 16).
Zone Definitions
[00] Null Zone
The zone is vacant. Unused zones should be programmed as
Null zones.
[01] Final Door Set Zone
If this zone type is programmed, inifinite exit delay will com-
mence when arming is initiated. In order to complete the arm-
ing sequence after infinite exit delay has begun, the Final
Door Set zone will have to be violated and restored. When the
system is armed, this zone will function as a Delay Zone.
[02] Delay Zone
This zone type, normally used for entry/exit doors, can be vio-
lated during the exit delay time without causing an alarm.
Once the exit delay has expired, opening the zone will start
the entry delay timer. During the entry delay time, the keypad
buzzer will sound steadily to advise the user that the system
should be disarmed. If the panel is disarmed before the entry
time expires, no alarm will be generated.
[03] Instant Zone
This zone type will cause an instant alarm if it is violated when
the panel is armed. Typically, this zone is used for windows,
patio doors or other perimeter zones, and glass break detectors.
[04] Interior Zone
This zone will not cause an alarm if violated during the entry
delay. If the zone is violated before the entry delay has begun, it
will cause an instant alarm. Typically, this zone is used for interior
protection devices, such as motion detectors.
[05] Interior Stay/Away Zone
This zone type works similarly to the Interior zone type, except that
it will be automatically bypassed under the following conditions:
• When the panel is armed in the Stay Mode (see section
3.6 "Function Keys" on page 11).
• When the panel is armed without entry delay (see "[*][9]
Arming Without Entry Delay" on page 11).
• When the panel is armed with an access code and a
Delay type zone is NOT tripped during the exit delay.
The automatic bypass prevents the user from having to manu-
ally bypass interior type zones when arming at home. This
zone is typically used for interior protection devices, such as
motion detectors.
[06] Delay Stay/Away Zone
This zone type will operate similarly to Interior Stay/Away
zones, except that it will always provide an entry delay. Typi-
cally, this zone is used for interior protection devices, such as
motion detectors. This zone option will help prevent false
alarms since it always provides an entry delay time for the
user to turn off the panel.
NOTE: Hardwire motion detectors covering entry/exit doors
that are using wireless transmitters must be programmed as
Delay Stay/Away. If not, the panel may see the motion detector
violation before the entry/exit transmitter has time to transmit to
the receiver, causing a false alarm.
[07] Delayed 24-hr Fire Zone
NOTE: Do not wire Fire zones on keypad zone terminals if the
DEOL supervision option is enabled for the panel (section
[013], option [2]).
When this zone is violated, the alarm output will be immedi-
ately activated (pre-alert) but the communicator will be
delayed for 30 seconds. If the user presses any key on any
keypad during this delay, the alarm output and the communi-
cator will be delayed an additional 90 seconds, giving the
user time to correct the problem. If the zone is still violated
after the 90 second delay, the panel will sound the alarm out-
put and delay the communicator for 30 seconds.
If the user does not press a key during the 30 second pre-
alert, the alarm output will latch and the panel will communi-
cate the alarm to the central station. The alarm will sound until
the Bell Cutoff time expires (Section [005] "System Times"), or
until a code is entered (see Section 5.13 "Bell" on page 23).
NOTE: If a second Fire type zone is violated or if the Fire keys
are pressed during the delay period, the panel will latch the
alarm output and will immediately communicate the alarm.
15