Advertisement
Table of Contents
- 1 Table of Contents
- 2 Sliding Doors for All Spaces with SKYTTA
- 3 Tools
- 4 Before You Start
- 5 SKYTTA Parts
- 6 To Think about
- 7 Height Options
- 8 The Doors Fit Perfectly
- 9 A Little Space Left above the System
- 10 A Lot of Space Left above the Door
- 11 The Doors Are too High
- 12 Sloped Ceiling
- 13 More Information
- 14 Services
- Download this manual
Advertisement
Table of Contents
Related Manuals for IKEA SKYTTA
Summary of Contents for IKEA SKYTTA
- Page 1 SKYTTA installation guide...
-
Page 2: Table Of Contents
You can do it yourself, but you don’t have to This brochure is your guide to preparing and installing Although our SKYTTA system is designed to be as the SKYTTA system by yourself. Inside you’ll find clear simple as possible for you to assemble and install it steps to follow as well as useful tips and ideas. -
Page 3: Sliding Doors For All Spaces With Skytta
Room divider Plan on paper or use the planner tool Planning your SKYTTA sliding doors can be a bit tricky, and it’s important that all the measurements are correct and aligned. It’s perfectly fine to plan on paper if that’s what you prefer, but there’s also a planner tool available... -
Page 4: Tools
Tools Here is a summary of the basic tools you’ll need. In ad- dition you’ll find what tools to use for each product in their respective Assembly Instructions. Basic tools Try square Screwdriver Hammer Pencil rasp Carpenter’s rule Saw and Miter box Hacksaw Step ladder Electric drill... -
Page 5: Before You Start
Use SKYTTA Make sure you have the space to cut the rails and as- planning tool. - Page 6 Before you start Marking key measurements Mark with a line all around the opening where you are going to place the system. Mark the front of the system as in the illustration to the right. A crosshair laser is recommended to use. Note! From the front of the storage solution to the front of the track/rails, you need 100 mm for a 2-track solution and 140 mm for a 3-track solution.
-
Page 7: Skytta Parts
SKYTTA parts Since SKYTTA packages are picked together for each Main Assembly Instruction for the system is to be system combination you will have some different found in the fitting package for the end doors. packages. Below is an overview of the different pack- This main Assembly Instruction will refer to other ages and parts. -
Page 8: To Think About
Wood beam has a front side on the 3-track rail but is symmetric on the 2-track. Have screws with you as these are not included by IKEA. Ceiling rail... - Page 9 Door assembly Mount door/clean floor rail Door has two symmetrical side rails, bottom rail and top rail, marked with tape. Clean the floor rail before mounting as dust can get stuck on the wheels. This Wheel fitting is placed in the bottom and guide fitting in the top. Click in the hori- should be done regularly to maintain a nice sliding of the doors.
-
Page 10: Height Options
Sloping ceiling solution If your doors are too high for your space, you can If you want to install SKYTTA sliding doors onto a reduce their height. First see general tips on page sloped ceiling, you need to leave extra wall space to 8-9, and then continue to page 12 and follow the As- create a 90 degree angle with the wall. -
Page 11: The Doors Fit Perfectly
The doors fit perfectly If the SKYTTA doors fit your space perfectly, you as- semble them normally. In this illustration, you can see what the system would look like. You will find the main Assembly Instruction in basic fitting package. This main instruction will refer to the other Assembly Instructions depending on the options you have chosen. -
Page 12: A Little Space Left Above The System
A little space left above the system – reduce ceiling height In case there is a little space left between the doors are not sold by IKEA. In this illustration, you can see and the ceiling, you need to compensate the ceiling what the system would look like. -
Page 13: A Lot Of Space Left Above The Door
In this illustration, ceiling is bigger, you need to compensate the ceiling you can see what the system would look like in this height with SKYTTA ceiling height reducer and cover situation. panels. You can also ask for help from a professional car-... -
Page 14: The Doors Are Too High
Height options The doors are too high – reduce door height In case the SKYTTA doors are too high, you need to For this situation, we strongly recommend to get the cut the door frame and the panel. Please be aware help of a professional carpenter with the appropriate that this is not possible for glass or mirror panels. -
Page 15: Sloped Ceiling
Height options Sloped ceiling solution If you want to install SKYTTA sliding doors onto a sloped ceiling, you need to leave extra wall space SKYTTA ceiling rail must be mounted onto a flat which is wider than the width of the rail, and which surface which is parallel with the floor. -
Page 16: More Information
IKEA products are designed to be taken home and assembled yourself. But if you would like some help, we can offer you a range of services. Contact your local store or visit the IKEA web- site for details. www.IKEA.com Home delivery...