Related Manuals for Panasonic AW-PH405N
Summary of Contents for Panasonic AW-PH405N
-
Page 1: Operating Instructions
Operating Instructions Indoor Pan-tilt Head AW-PH405N Model No. Before operating this product, please read the instructions carefully and save this manual for future use. Printed in Japan F0107Y0 VQTB0150... -
Page 2: Safety Precautions
Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”... -
Page 3: Important Safety Instructions
Safety precautions IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. ) Keep these instructions. -
Page 4: Table Of Contents
Contents Safety precautions ... 2 Operating precautions ... 5 Introduction ... 5 Accessories ... 6 Installation precautions ... 6 Parts and their function ... 7 Installation ... 11 Assembling the pan-tilt head ... 11 Concerning the safety modes ... 1 ... -
Page 5: Operating Precautions
Operating precautions Handle the unit carefully. Dropping the unit or subjecting it to strong impact may give rise to malfunctioning or accidents. Turn off the power before connecting or disconnecting the cables. Be absolutely sure to turn off the power before connecting or disconnecting the cables. -
Page 6: Accessories
Accessories Operating instructions ... 1 Rotary arm ... 1 Camera mounting base ... 1 Mounting screws for the rotary arm and camera mounting base (with flat washers, spring washers) M522 mm ... 7 Camera cable ... 1 Tally lamp ... 1 Tally mounting screws (M36 mm) ... -
Page 7: Parts And Their Function
Parts and their function... -
Page 8: Parts And Their Function
Parts and their function Rotary head This rotates in the horizontal direction. Pedestal POWER ON/OFF switch Where a switch is pushed in, the unit’s power is turned on, and the unit’s power is turned off after the switch has jumped out. - Page 9 Parts and their function ND/EXT connector [ND/EXT] This is for the control of the ND filter and lens extender of the motorized lens unit. Connect this connector when using a motorized lens unit with ND filter and lens extender functions. The cable described in “Cable specifications”...
- Page 10 Parts and their function CONTROL IN RP connector [RP] This is the connector for the control of signals of the camera and pan-tilt head. It is connected to the TO PAN/TILT HEAD connector on the AW-RP655 multi-function controller and AW-RP555 multi hybrid control panel.
-
Page 11: Installation
Installation Assembling the pan-tilt head When assembling the pan-tilt head, use the Allen key (provided) and screwdriver, and secure the head by tightening the screws firmly. After mounting the pan-tilt head, check there is no play in its installation. ... - Page 12 Installation Mounting the tally lamp Connect the cable connector which is taped to the top of the pan-tilt head to the tally cable connector. Mount the tally lamp on the top of the pan-tilt head using the two screws provided. Mount the lamp while paying attention to the wire.
-
Page 13: Concerning The Safety Modes
Installation Concerning the safety modes This unit comes with two safety modes which are designed to safeguard the user and others from injury and to prevent damage to the pan-tilt head. 1. Mode for ensuring safety in the case of collisions When the rotary arm of the pan-tilt head or some other unit installed on the head keeps colliding with an obstruction or a person (approx. -
Page 14: Procedure For Changing The Settings Of The Cpu Circuit Board Switches
Installation Procedure for changing the settings of the CPU circuit board switches Follow the steps below to change the settings of the CPU circuit board switches. Remove the four screws, and gently remove the housing case. Disconnect the tally cable connector. ... -
Page 15: Setting The Cpu Circuit Board Switches
Installation Setting the CPU circuit board switches Setting SW1 These switches are used to set the operations of the AW-PH405. Before changing their settings, make sure that the power has been turned off. No.1: Auto focus (AF)/extender (EXT) selector switch. Use this at the ON position when using an auto focus lens which is connected to the LENS I/F (1) connector;... -
Page 16: Pan-Tilt Head Mounting Conditions
Installation Pan-tilt head mounting conditions Pan-tilt Mounting Compatible head weight specifications cameras Convertible camera series AW-E50 AW-E650 Stand-alone AW-E655 Approx. lbs installation or AW-E750 (10 kg) installation on AW-E860 the celling Multi-purpose camera series AK-HC1500G Mounting the pan-tilt head Recommended screws No. - Page 17 Installation For a stand-alone installation For installation on the ceiling Note When installing the pan-tilt head, do not forcibly turn the rotary head or rotary arm manually. Doing so may result in malfunctioning.
-
Page 18: Mounting The Camera (Convertible Camera Aw-E50/E650/E655/E750/E860)
Installation Mounting the camera [Convertible camera AW-E350/E650/E655/E750/E860 When mounting the camera, take sufficient care to ensure that the camera will not come off or fall down. Mount the lens onto the convertible camera. (Before mounting a large lens, consult with your dealer.) ... -
Page 19: Attaching The Wire (Convertible Camera Aw-E50/E650/E655/E750/E860)
Installation Attaching the wire [Convertible camera AW-E350/E650/E655/E750/E860 The camera comes with a wire for preventing the camera from dropping. Follow the instructions below to use it to couple the camera to the pan-tilt head. When mounting the cameras with fan (AW-E655, AW-E750, AW-E860) ... -
Page 20: Mounting The Camera (Mulit-Purpose Camera Ak-Hc1500G)
Installation Mounting the camera [Multi-purpose camera AK-HC1500G When mounting the camera, take sufficient care to ensure that the camera will not come off or fall down. Mount the lens onto the multi-purpose camera. (1) Lenses that can be used •... -
Page 21: Concerning The Balance Of The Installed Unit
Installation Concerning the balance of the installed unit The weight balance may be impaired when the pan-tilt head is used in combination with a camera and long lens. Follow steps to below to check the balance, and then mount the camera. If, after this, the balance is still impaired and operations cannot be performed smoothly, it means that the balance must be adjusted. - Page 22 Installation Precautions for mounting the camera Bearing in mind the length of the lens, set the movement range of the pan-tilt head using the limiters in such a way that the hood at the edge of the lens will not come into contact with the surface on which the pan-tilt head is installed when the pan-tilt head is tilted.
-
Page 23: Attaching The Wire (Mulit-Purpose Camera Ak-Hc1500G)
Installation Attaching the wire [Multi-purpose camera AK-HC1500G The camera comes with a wire for preventing the camera from dropping. Follow the instructions below to use it to couple the camera to the pan-tilt head. Use the wire mounting screw (M48 mm with flat washer and spring washer) to attach one end of the wire to the pan-tilt head’s arm. -
Page 24: Connections
Connections Turn off the power of all the equipment before proceeding with the connections. Connect the AC power cable supplied with the AW-PH405 for the AW-PH405 indoor pan-tilt head. Use 10BASE-T straight cables to connect the RP connectors on the pan-tilt heads with the CONTROL OUT TO PAN/TILT HEAD (1 to 5) connectors on the AW-RP655 multi-function controller and AW-RP555 multi hybrid control panel. - Page 25 Connections For the AK-HC1500G Note Set the menu items to protocol 4. 10BASE-T straight cable Pan-tilt head/camera control signals AW-RP555 Multi Hybrid Control Panel AW-RP655 Multi-function controller AW-CB400 Remote operation panel Use the connecting cables below to connect the pan-tilt head and camera. AW-CA15H9G ...
-
Page 26: Cable Specifications
Cable specifications When connecting a Canon lens with motorized extender unit Connector: HR10A-10P-10P (73) made by Hirose Electric CVCC (12 V) CGND EXT Return EXT Signal ND Return ND Signal CanonEXT () CanonEXT () Connect this connector to the ND/EXT connector on the pan-tilt head When connecting a Fujinon extender change unit Connector: HR10A-10P-10P (73) -
Page 27: Replacing The Consumable Parts
Replacing the consumable parts Replacing the motor Replace the motor when it ceases to operate properly. For details on the motor replacement, consult your dealer. Replacing the belt Replace the belt when the preset stop accuracy has deteriorated. For details on the belt replacement, consult your dealer. -
Page 28: Appearance
Appearance Unit: inch (mm) 1-9/16 (19) 5-/8 (17) 7-/16 (18) -1/16 -1/16 (71) (97) 6-5/8 (168) ø6-5/16 (160) ø6-5/16 (160) ø5-/4 ø5-/4 (146) (146) ø6-5/16 4-M6 screws (160) <Mounting hole specifications>... -
Page 29: Specifications
Specifications Supply voltage: AC 10 V, 60 Hz Power consumption: 10 W indicates safety information. Genlock input: Black burst or composite video signal, Tri Sync Prompter input (PROMPTER IN): Through output to PROMPTER connector Prompter output (PROMPTER OUT): D-SUB 15-pin Camera video output VIDEO: BNC, 75-ohm output... - Page 30 Memo — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
- Page 31 Memo — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
- Page 32 PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (01) 48-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (01) 48-761 Southeast Region: 15 Northbrook Parkway, Ste 1-160, Suwanee, GA 004 (770) 8-685...