Yaesu FT-2000/D Technical Supplement page 37

REV-ALC Adjustment
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d40 rAC."
Rotate the [SUB(VFO-B)] knob so that the VFO-B
frequency display.
A M M
LIGNMENT ENU ODE
1.820 MHz CW-U
3.570 MHz CW-U
7.050 MHz CW-U
10.100 MHz CW-U
14.200 MHz CW-U
18.100 MHz CW-U
21.200 MHz CW-U
24.900 MHz CW-U
29.690 MHz CW-U
53.900 MHz CW-U
Perform the same procedures for the Alignment
Menus "d40 rAC" through "d49 rAC."
Press and hold in the [MENU] button for 2 sec-
onds to save the new setting and exit from the
alignment mode.
FM MAX Deviation Adjustment
Connect the Dummy Load, Wattmeter, and De-
viation Meter to the "ANT 1" Jack.
Set the Main Band (VFO-A) frequency to 28.700
MHz in the FM mode.
Connect the Audio Generator to
pin 8 of the MIC jack (pin 7:
GND), then set the output level
to 10 mV @1 kHz.
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d51 F45."
Press the PTT switch, then rotate the [SUB(VFO-
B)] knob for 4.5 kHz (±0.2 kHz) on the Deviation
Meter.
Release the PTT switch.
Set the Main Band (VFO-A) operating mode to
the FM-N mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d52 F23."
Press the PTT switch, then rotate the [SUB(VFO-
B)] knob for 2.25 kHz (±0.15 kHz) on the Devia-
tion Meter.
Release the PTT switch.
Press and hold in the [MENU] button for 2 sec-
S S- 100W T 200W T
UB METER YPE
d40 rCA 60
d41 rCA 60
d42 rCA 60
d43 rCA 60
d44 rCA 60
d45 rCA 60
d46 rCA 60
d47 rCA 60
d48 rCA 60
d49 rCA 60
UK: 51.900 MHz, EU: 50.390 MHz, FRA: 51.190 MHz
MIC IN
MIC GND
onds to save the new setting and exit from the
alignment mode.
COMP Meter Adjustment
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d57 C10," then rotate the
[SUB(VFO-B)] knob for "10 dB" on the COMP
YPE
meter.
41
45
Rotate the Main Tuning Dial knob to select the
43
41 alignment parameter "d58 C20," then rotate the
47
[SUB(VFO-B)] knob for "20 dB" on the COMP
34
32
meter.
34
Rotate the Main Tuning Dial knob to select the
29
22
alignment parameter "d59 C30," then rotate the
[SUB(VFO-B)] knob so that the COMP meter de-
flects to full scale.
Press and hold in the [MNU] key for 2 seconds
to exit from the alignment mode.
SWR Meter Adjustment
Switch the external display to "SWR Monitor"
page.
Connect the 50-Ohm Dummy Load and Wattme-
ter to the "ANT 1" Jack, then set the [METER]
switch to the "SWR" position.
Disconnect the 3-pin plug from J1015 on the
MAIN Unit, then apply a 4.2 V DC voltage to pin
2 of J1015, and 2.1 V DC to pin 3 of J1015.
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d53cS30."
Press the PTT switch, then rotate the [VRF] knob
so that the SWR meter (on the external display)
reading is "3.0." The SWR meter reading (3.0) is
broad (few points). Therefore, set the [VRF] knob
to the center of this broad range.
Rotate the [SUB(VFO-B)] knob so that the SWR
meter (on the front panel) reading is "3.0."
Release the PTT switch.
Perform the same procedures for the Alignment
Menus "d54cS30" and "d55cS30."
Apply a 4.2 V DC voltage to pin 2 of J1015, and
1.4 V DC to pin 3 of J1015.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d53bS20."
Press the PTT switch, then rotate the [SUB(VFO-
Alignment
ALIGNMENT-21