Yaesu FT-2000/D Technical Supplement page 36

Alignment
erator output level to the position where the ALC
meter just starts to deflect.
Release the PTT switch, then increase the Audio
Generator output level for "9 dB."
Press the [ENT] key, while pressing and holding
in the PTT switch, then rotate the [SUB(VFO-B)]
knob for maximum deflection on the ALC meter
zone (S9+10dB).
Release the PTT switch, then press and hold in
the [MENU] button for 2 seconds to save the new
setting and exit from the alignment mode.
TX Output Power/PO Meter/TXG Adjustment
Referring to table below, tune the transceiver to
each frequency listed.
B
AND
1.8 MHz Band
3.5 MHz Band
7 MHz Band
10 MHz Band
14 MHz Band
18 MHz Band
21 MHz Band
24.5 MHz Band
28 MHz Band
50 MHz Band
Connect the 50-Ohm Dummy Load and Wattme-
ter to the "ANT 1" jack.
Set the Main Band (VFO-A) frequency to 1.820
MHz in the CW mode.
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Dial knob to select the alignment
parameter "d18AP2h."
Rotate the [SUB(VFO-B)] knob so that the VFO-B
frequency display shows "0."
Rotate the [VRF] knob for 100 W (or 200W) on
the PO meter.
Press the PTT switch, then rotate the [SUB(VFO-
B)] knob for 100 W (or 200W) on the Wattmeter.
Rotate the [CLAR] knob so that the Sub S-meter
deflects to "S-9."
Release the PTT switch.
Perform the same procedures for the Alignment
Menus "d18bP1h" through "d27EP10," per the
chart at the right.
AM-TXG Adjustment
Connect the 50-Ohm Dummy Load and Wattme-
ter to the "ANT 1" jack.
Rotate the [RF PWR] knob to fully clockwise.
Set the Main Band (VFO-A) frequency to 14.200
MHz in the AM mode.
ALIGNMENT-20
VFO-A F M
REQUENCY ODE
1.820 MHz CW
3.570 MHz CW
7.050 MHz CW
10.100 MHz CW
14.200 MHz CW
18.100 MHz CW
21.200 MHz CW
24.900 MHz CW
28.700 MHz CW
52.000 MHz CW
UK: 51.000 MHz, EU: 50.250 MHz, FRA: 50.700 MHz
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d29 tCA."
Rotate the [SUB(VFO-B)] knob so that the VFO-B
frequency display shows "0."
Press the PTT switch without microphone input,
then rotate the [SUB(VFO-B)] knob for 35 W (±5
W) (200 W Type: 70 W (±5 W)) on the Wattmeter.
Release the PTT switch.
Press and hold in the [MENU] button for 2 sec-
onds to save the new setting and exit from the
alignment mode.
A M VFO-B F . D
LIGNMENT ENU REQ ISPLAY
d18bP1h 0
d18bP1h 0
d18cP50 0
d18dP20 0
d18EP10 0
d19AP2h 0
d19bP1h 0
d19cP50 0
d19dP20 0
d20EP10 0
d20AP2h 0
d20bP1h 0
d20cP50 0
d20dP20 0
d20EP10 0
d21AP2h 0
d21bP1h 0
d21cP50 0
d21dP20 0
d21EP10 0
d22AP2h 0
d22bP1h 0
d22cP50 0
d22dP20 0
d22EP10 0
d23AP2h 0
d23bP1h 0
d23cP50 0
d23dP20 0
d23EP10 0
d24AP2h 0
d24bP1h 0
d24cP50 0
d24dP20 0
d24EP10 0
d25AP2h 0
d25bP1h 0
d25cP50 0
d25dP20 0
d25EP10 0
d26AP2h 0
d26bP1h 0
d26cP50 0
d26dP20 0
d26EP10 0
d27AP2h 0
d27bP1h 0
d27cP50 0
d27dP20 0
d27EP10 0
100W T 200W T
YPE YPE
S S-
UB METER
PO / PO /
METER ATTMETER METER ATTMETER
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9
100 W 200 W S-9
50 W 100 W S-9
20 W 50 W S-9
10 W 20 W S-9
5 W 10 W S-9