Table of Contents
Advertisement
I/O Circuits
NPN Open-collector Outputs
Operation
Model
Dark-ON mode
One beam
or more is
interrupted
No beam is
interrupted
F3W
-D052A
F3W
-D052AP
F3W
-D052B
F3W
Light-ON mode
-D052BP
No beam is
interrupted
One beam
or more is
interrupted
UNI-WIRE Transmission Outputs
Operation
Model
Dark-ON mode
One beam
or more is
interrupted
No beam is
interrupted
F3W
-D052U
F3W
-D052UP
Light-ON mode
No beam is
interrupted
One beam
or more is
interrupted
Downloaded from
Elcodis.com
electronic components distributor
Timing chart
mode
No beam is interrupted
Light
ON:
incident
One beam or more is interrupted
Operation indicator
ON
(orange)
OFF
ON
Control output
OFF
OFF:
Operate
Load (relay, etc.)
Reset
No beam is interrupted
Light
ON:
incident
One beam or more is interrupted
Operation indicator
ON
(orange)
OFF
OFF:
ON
Control output
OFF
Operate
Load (relay, etc.)
Reset
Timing chart
Mode
ON:
No beam is interrupted
Light
incident
One beam or more is interrupted
Operation indicator
ON
(orange)
OFF
ON
OFF:
UNI-WIRE output
OFF
ON:
No beam is interrupted
Light
incident
One beam or more is interrupted
Operation indicator
ON
(orange)
OFF:
OFF
ON
UNI-WIRE output
OFF
http://www.ia.omron.com/
Mode
selector
switch
F3W-D052A@-L/B@-L
Six
Different
picking
Power
frequency
indicators
indicator
indicator
(orange)
(green)
(green)
D-ON
Emitter
main
(DARK
5 V
circuit
External picking
ON)
indicator output
Brown
1
Load
*2
50 mA max.
2
Blue
*2
*1
Note: The circled numbers represent the pin numbers for Pre-wired Connector
Models.
*1. The sections surrounded by single-dashed lines are applicable to the F3W-
D052AP-L/BP-L only.
*2. The circled numbers represent external picking indicator output pin
numbers.
The following diagram shows the relationship between the picking in-
struction input, picking indicator status, and external picking indicator
output. DIP switch 1 is used to switch the picking display mode be-
L-ON
tween all lighting, all flashing, elevator-like lighting, and accordion-
(LIGHT
like lighting. It is also possible to switch the external picking indicator
ON)
display mode between lighting and flashing.
Open
Picking instruction
input
Picking indicator
(orange)
OFF
External picking
indicator output
OFF
Mode
selector
switch
F3W-D052U@-L
Six
Different
picking
Power
frequency
indicators
indicator
indicator
(orange)
(green)
(green)
D-ON
Emitter
(DARK
main
circuit
External picking
ON)
indicator output
Brown
Load
1
UNI-WIRE
*2
50 mA max.
circuit
2
Blue
*2
*1
*1. The sections surrounded by single-dashed lines are applicable to the F3W-
D052UP-L only.
*2. The circled numbers represent external picking indicator output pin
numbers.
The following diagram shows the relationship between the picking in-
struction input, picking indicator status, and external picking indicator
output. DIP switch 1 is used to switch the picking display mode be-
tween all lighting, all flashing, elevator-like lighting, and accordion-like
lighting. It is also possible to switch the external picking indicator dis-
L-ON
play mode between lighting and flashing.
(LIGHT
The instruction input address is set with DIP switch 2.
ON)
Picking instruction
input (transmission input)
Picking indicator
(orange)
External picking
indicator output
6
(c)Copyright OMRON Corporation 2008 All Rights Reserved.
F3W-D
Output circuit
F3W-D052A@-D/B@-D
Operation
Stability
indicator
indicator
Orange/purple
Orange/purple
(green)
(orange)
stripe
stripe
5
5
(Sync line)
Brown
Brown
1
1
Load
12 to 24
(Control
VDC
Black
output)
4
100 mA
max.
5 V
Pink
Pink
2
2
Picking
instruction
input
Blue
Blue
3
3
0 V
ON
ON
Output circuit
F3W-D052U@-D
UNI-WIRE transmission line
Trans-
Trans-
Stability
mission
mission
indicator
indicator
indicator
(orange)
(orange)
(green)
Brown
White
Black
Blue
Brown
White
UNI-WIRE
circuit
Black
Blue
ON
OFF
ON
OFF
ON
OFF
Six picking
indicators
(orange)
Receiver
main
circuit
Opera-
Six
tion
picking
indicator
indicators
(orange)
(orange)
Receiver
main
circuit
6
Advertisement
Table of Contents
