Digital Input (Digital In) Terminal Setting - JVC RX-8010PBK Instructions Manual

Low Fr equency Effect At t enuat or Set t ing
If the bass sound is distorted while playing back a source using
Dolby Digital or DTS Digital Surround, follow the procedure below.
On t he fr ont panel ON LY:
1. Press SETTING repeatedly until
"LFE ATT" (Low Frequency
Effect Attenuator) appears on the
display.
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to select the low frequency effect
attenuator level.
• Each time you press the button, the display
changes to show the following:
0dB
0dB: Normally select this.
10dB: Select this when the bass sound is distorted.
Notes:
• Low frequency effect attenuator is not valid for the DVD MULTI
playback mode.
• This function takes effect only when the Dolby Digital or DTS Digital
Surround sounds with LFE signal comes in (with "SUBWOOFER"
set to "YES").
Digit al Input (DIGITAL IN ) Ter minal
Set t ing
When you use the digital input terminals, you have to register what
components are connected to which terminals (DIGITAL IN 1/2/3/4).
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On t he fr ont panel ON LY:
To set t he DIGITAL 1 t er minal:
1. Press SETTING repeatedly until
"DGTL COAX" (Digital Coaxial)
appears on the display.
The display changes to show the current setting
for DIGITAL 1 terminal.
2. Press CONTROL UP 5/DOWN ∞
to select the appropriate digital
terminal setting.
• Each time you press the button, the display
changes to show the following:
1: DVD " 1: MD ** " 1: CDR " 1 : TV (or DBS * ) "
1: CD " (back to the beginning)
*
If you have changed the source name from "TV" to "DBS,"
"DBS" appears (see page 16).
**
Change the source name to "MD" for TAPE/MD jacks when you
use an MD recorder (see page 16).
19
CT SETTING
CONTROL
DOWN UP
10dB
CT SETTING
CONTROL
DOWN UP
To set t he DIGITAL 2 / 3 / 4 t er minals:
1. Press SETTING again until
DIGITAL 2/3/4 terminals' setting
appears on the display.
The display changes to show the current settings.
DIGITAL 2 terminal setting
DIGITAL 3 terminal setting
2. Press CONTROL UP 5/DOWN ∞
to select the appropriate digital
terminal settings.
• Each time you press the buttons, the
display changes to show the following:
When the DGTL COAX (DIGITAL 1) is set to "DVD"
2: CD 3: TV (or DBS * ) 4: CDR "
2: CD 3: TV (or DBS * ) 4: MD ** "
2: CD 3: MD ** 4: CDR "
2: MD ** 3: TV (or DBS * ) 4: CDR "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "MD" **
2: CD 3: TV (or DBS * ) 4: DVD "
2: CD 3: DVD 4: CDR "
2: DVD 3: TV (or DBS * ) 4: CDR "
2: CD 3: TV (or DBS * ) 4: CDR "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "CDR"
2: MD ** 3: TV (or DBS * ) 4: DVD "
2: CD 3: TV (or DBS * ) 4: DVD "
2: CD 3: TV (or DBS * ) 4: MD ** "
2: CD 3: MD ** 4: DVD "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "TV" or "DBS"
2: CD 3: MD ** 4: CDR " 2: MD ** 3: DVD 4: CDR "
2: CD 3: DVD 4: CDR " 2: CD 3: DVD 4: MD ** "
(back to the beginning)
When the DGTL COAX (DIGITAL 1) is set to "CD"
2: DVD 3: TV (or DBS * ) 4: MD ** "
2: DVD 3: MD ** 4: CDR "
2: MD ** 3: TV (or DBS * ) 4: CDR "
2: DVD 3: TV (or DBS * ) 4: CDR "
(back to the beginning)
* If you have changed the source name from "TV" to "DBS,"
"DBS" appears (see page 16).
**
Change the source name to "MD" for TAPE/MD jacks when you
use an MD recorder (see page 16).
Note:
When shipped from the factory, the DIGITAL IN terminals have been
set for use with the following components.
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
• DIGITAL 3 (optical): For digital TV broadcast tuner
• DIGITAL 4 (optical): For CD recorder
T SETTING
DIGITAL 4 terminal setting
CONTROL
DOWN UP