Dremel Lite 7760 Operating/Safety Instructions Manual
Hide thumbs
Also See for Lite 7760:
- Operating/safety instructions manual (101 pages) ,
- Original instructions manual (197 pages)
Related Manuals for Dremel Lite 7760
Summary of Contents for Dremel Lite 7760
- Page 1 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 2 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 3: General Power Tool Safety Warnings
General Power Tool Safety Warnings Prevent unintentional starting. Ensure the Keep cutting tools sharp and clean. switch is in the off-position before Properly maintained cutting tools with connecting to power source and / or sharp cutting edges are less likely to bind battery pack, picking up or carrying the and are easier to control. - Page 4 Safety Rules for Rotary Tools normally break apart during this test time. ▶ Safety warnings common for Wear personal protective equipment. grinding, sanding, wire Depending on application, use face shield, brushing, polishing, carving safety goggles or safety glasses. As or abrasive cutting-off appropriate, wear dust mask, hearing operations: protectors, gloves and workshop apron...
-
Page 5: Kickback And Related Warnings
Safety Rules for Rotary Tools Do not run the power tool while carrying it conditions and can be avoided by taking at your side. Accidental contact with the proper precautions as given below. spinning accessory could snag your Maintain a firm grip on the power tool and clothing, pulling the accessory into your position your body and arm to allow you to body. - Page 6 Safety Rules for Rotary Tools loading and susceptibility to twisting or edge of the workpiece on both sides of the snagging of the wheel in the cut and the wheel. possibility of kickback or wheel breakage. Use extra caution when making a pocket Do not position your hand in line with and into existing walls or other blind behind the rotating wheel.
- Page 7 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 8 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 9 Symbols Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Designation / Explanation Volts (voltage) Amperes (current) Hertz (frequency, cycles per second) Watt (power)
- Page 10 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 11 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 12: Charging The Tool
Charging the Tool Your Dremel Lite 7760 does not come ▶ Important Charging Notes completely charged from the factory. Be sure to charge tool prior to initial use. Lithium-ion battery will hold its charge while in storage for up to 2 Insert USB cable 13 into USB port of years so it’s always ready when you... - Page 13 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 14 The major difference to the 3 - Versatile user is that in the high speed tools, the The Dremel Lite 7760 comes with a 10- GlobalTestSupply www. .com Find Quality Products Online at:...
- Page 15 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 16: Operating Speeds
Operating Speeds To select the right speed for each job, use a the tool when overload and stall practice piece of material. conditions occur. If you stall the tool for too long, or bind the bit in a work piece, especially at high speeds, the tool will ▶... - Page 17 Leaning on the tool does not help. Some rules of thumb in regard to speed: Your Dremel Lite 7760 can be used with Plastic and other materials that melt all of the Dremel accessories, except at low temperatures should be cut at router bits.
- Page 18 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 19 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 20 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 21 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 22 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 23 Dremel Attachment Compatibility Model No. Description Compatibility with 7760 220 / Workstation Not Advised 220-01 Flex Shaft Not Advised Router Table Not Advised 335 / Plunge Router 335-01 Dust Blower 4486 Dremel Chuck Not Advised A550 Shield Multi-purpose Cutting Kit...
- Page 24 Dremel Attachment Compatibility Model No. Description Compatibility with 7760 A577 Detailer’s Grip 670 / Mini-saw 670-01 Lawn Mower and Garden Tool Sharpener 678 / Circle Cutter and Not Advised 678-01 Straight Edge Guide A679-02 Chain Saw Sharpener 2500 / Multi-vise...
- Page 25 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 26 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
- Page 27 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 28: Speed Settings
Speed Settings Note: Each number settings listed in the speed charts = x 1,000 RPM * Speed for light cuts, Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Note that the recommended speed may not be suitable for your rotary tool model. High Speed Cutters Catalog Soft... - Page 29 Speed Settings Note: Each number settings listed in the speed charts = x 1,000 RPM * Speed for light cuts, Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Note that the recommended speed may not be suitable for your rotary tool model. Tungsten Carbide Cutters Catalog Soft...
- Page 30 Speed Settings Note: Each number settings listed in the speed charts = x 1,000 RPM * Speed for light cuts, Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Note that the recommended speed may not be suitable for your rotary tool model. Cutting Accessories Catalog Soft...
- Page 31 Speed Settings Note: Each number settings listed in the speed charts = x 1,000 RPM * Speed for light cuts, Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Note that the recommended speed may not be suitable for your rotary tool model. Flapwheels Catalog Soft...
- Page 32 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...