One for All URC-5600 Cinema 5 User Manual page 4

SETTING UP OTHER COMPONENTS
In addition to the components labeled on the device keys (TV, VCR, DVD/LD,
CBL/SAT, etc.), the Cinema 5 can also operate the following components:
Cassette Decks, Video Accessories and Miscellaneous Audio Components
(Graphic Equalizers and Digital Music Service Boxes).
The Setup Codes for these components can be accessed under the following
device keys:
Cassette Decks: Use the VCR Key
Video Accessories: Use the CBL/SAT Key
Miscellaneous Audio: Use the RCVR Key
For example, to set up a Cassette Player on the VCR key:
1. Turn on your Cassette Player and insert a tape.
2. Press VCR and release. Press and hold SETUP until the
Cinema 5 's red light blinks twice, then release SETUP.
3. Enter the first four-digit Cassette Player code listed for your
brand in the "Setup Codes For Audio Cassettes" section. If
you perform this procedure correctly, the red light will blink
twice when you enter the final digit of your code.
4. Aim the Cinema 5 at your Cassette Player and press PL
(Play). Your Cassette Player should play your tape. If your
Cassette Player does not respond, repeat steps 2-4, trying
each code listed for your brand until you find the one that
operates your Cassette Player.
Your Cinema 5 is now programmed to operate your Cassette
5.
Player. Remember, if you want to use your Big Easy HT to
operate your Cassette Player, press the VCR key first.
RE-ASSIGNING DEVICE KEYS
You can use the Cinema 5 to operate a second TV or a second VCR or any
combination of five home entertainment components. For example, you may
want your Cinema 5 to control 1 TV, 1 Cable Converter, 1 Receiver and 2 DVD
Players. To accomplish this, you must re-assign one of the device keys to
operate the desired component, in this case, a second DVD. The chart below
shows you how to re-assign a particular device key and then set up your new
component.
TV to VCR SETUP* + 992 + VCR + TV + TV + SETUP* + VCR
code
TV to DVD/LD SETUP* + 992 + DVD/LD + TV + TV + SETUP* DVD
or LD layer code
TV to RCVR SETUP* + 992 + RCVR + TV + TV + SETUP* + Audio
code
TV to CBL/SAT SETUP* + 992 + CBL/SAT + TV + TV + SETUP*
+Cable/DBS code
VCR to TV SETUP* + 992 + TV + VCR + VCR + SETUP* + TV
code
VCR to DVD/LD SETUP* + 992 + DVD/LD + VCR + VCR + SETUP* +
DVD or LD Player code
VCR to RCVR SETUP* + 992 + RCVR + VCR + VCR + SETUP* +
Audio code
VCR to CBL/SAT SETUP* + 992 + CBL/SAT + VCR + VCR + SETUP* +
Cable/DBS code
DVD/LD to TV SETUP* + 992 + TV + DVD/LD + DVD/LD + SETUP* +
TV code
DVD/LD to VCR SETUP* + 992 + VCR + DVD/LD + DVD/LD + SETUP*
+ VCR code
DVD/LD to RCVR SETUP* + 992 + RCVR + DVD/LD + DVD/LD +
SETUP* + Audio code
DVD/LD to CBL/SAT SETUP* + 992 + CBL/SAT + DVD/LD + DVD/LD +
SETUP* + Cable/DBS code
RCVR to TV SETUP* + 992 + TV + RCVR + RCVR + SETUP* + TV
code
RCVR to VCR SETUP* + 992 + VCR + RCVR + RCVR + SETUP* +
VCR code
RCVR to DVD/LD SETUP* + 992 + DVD/LD + RCVR + RCVR + SETUP*
+ DVD or LD Player code
RCVR to CBL/SAT SETUP* + 992 + CBL/SAT + RCVR + RCVR +
SETUP* + Cable/DBS code
CBL/SAT to TV SETUP* + 992 + TV + CBL/SAT + CBL/SAT +
SETUP* + TV code
CBL/SAT to VCR SETUP* + 992 + VCR + CBL/SAT + CBL/SAT +
SETUP* + VCR code
CBL/SAT to DVD/LD SETUP* + 992 + DVD/LD + CBL/SAT + CBL/SAT +
SETUP* + DVD or LD code
CBL/SAT to RCVR SETUP* + 992 + RCVR + CBL/SAT + CBL/SAT +
SETUP* + Audio code
*NOTE: Here (*) you must hold SETUP until the Cinema 5's red light blinks
twice.
PROGRAMMING THE MACRO KEY
The Cinema 5 has a Macro key (MACRO) that allow the user to play back a
series of keystrokes, at any time, with the press of the key. For example, to set
up a sequence that will turn on your components and change the components to
the proper inputs:
1. Press and hold SETUP until the Cinema 5 's red light
blinks twice, then release SETUP.
9 - 9 - 5
9 - 9 - 5
2. Press 9 - 9 - 5. The Cinema 5 's red light will blink twice.
3. Press and release the MACRO key. This will be the key
that will play back the series of keystrokes assigned to that
key.
4. Begin entering the sequence of keystrokes, up to 15, that
you wish to be played back when you press the SETUP
key. For example:
RCVR + POWER + TV + POWER + TV/VCR (To change
the input on the TV to VIDEO 1) + CBL/SAT + POWER.
5. Once your sequence is entered, press and hold SETUP
until the Cinema 5 's red light blinks twice.
Now, using the example above, whenever the programmed MARCO key is
pressed, the Receiver would power ON, the TV will power ON and change
the input to VIDEO 1 and then the Satellite would power ON.
VOLUME LOCK
Volume Lock allows the user to designate which component will control the
volume in the TV, DVD/LD and CBL/SAT modes. To set the Volume Lock to
the TV mode:
1. Press and hold SETUP until the Cinema 5 's red light
blinks twice, then release SETUP.
9 - 9 - 3
9 - 9 - 3
2. Press 9 - 9 - 3. The Cinema 5 's red light will blink twice.
3. Press and release TV. The Cinema 5' s red light will blink
twice.
Now, whenever you press VOL , VOL
CBL/SAT modes your TV will control the volume. If you would like to
change the Volume Lock setting to the VCR, DVD/LD or CBL/SAT modes
repeat steps 1-3, only substitute the appropriate device key. Setting the
Volume Lock to the TV, VCR, DVD/LD or CBL/SAT mode will not effect the
volume control in the RCVR mode.
You can also change the Volume Lock setting so that an Audio component
controls the volume in all device modes. To change the Volume Lock setting
on the Cinema 5 to the RCVR mode:
1. Press and hold SETUP until the Cinema 5 's red light
blinks twice, then release SETUP.
9 - 9 - 3
9 - 9 - 3
2. Press 9 - 9 - 3. The Cinema 5 's red light will blink twice.
3. Press and release RCVR. The Cinema 5 's red light will
blink twice.
or MUTE in the VCR, DVD/LD and