Searching For Your Code - One for All URC-5600 Cinema 5 User Manual

repeat steps 2-4, trying each code listed for your brand
until you find the one that operates your DVD or Laser Disc
Player.
Your Cinema 5 is now programmed to operate your
5.
DVD or Laser Disc Player. Write your DVD or Laser Disc
Player code in the boxes to the left for future reference.
Remember, if you want to use your Cinema 5 to operate your DVD or Laser Disc
Player, press the DVD/LD key first.
Programming the Cinema 5 to operate your Receiver/Tuner:
Locate the brand name of your Receiver/Tuner and then write it in the space
below.
Receiver/Tuner Brand:
Locate the brand name of your Receiver/Tuner in the "Setup Codes For
Receivers/Tuners" section. The brands are listed in alphabetical order with the
most popular codes listed first. You will use one of these codes to program your
Cinema 5 to operate your Receiver/Tuner.
To program the Cinema 5 to operate your Receiver/Tuner:
1. Turn on your Receiver/Tuner.
2. Press RCVR and release. Press and hold SETUP until the
Cinema 5 's red light blinks twice, then release SETUP.
3. Enter the first four-digit Receiver/Tuner code listed for your
brand in the "Setup Codes For Receivers/Tuners" section.
If you perform this procedure correctly, the red light will
blink twice when you enter the final digit of your code.
4. Aim the Cinema 5 at your Receiver/Tuner and press
POWER. Your Receiver/Tuner should turn off. If your
Receiver/Tuner does not respond, repeat steps 2-4, trying
each code listed for your brand until you find the one that
operates your Receiver/Tuner.
5. Your Cinema 5 is now programmed to operate your
Receiver/Tuner. Write your Receiver/Tuner code in the
boxes to the left for future reference.
Remember, if you want to use your Cinema 5 to operate your Receiver/
Tuner, press the RCVR key first.
Programming the Cinema 5 to operate your Cable Converter or Satellite:
Locate the brand name of your Cable Converter or Satellite and then write
it in the space below.
Cable Converter Brand:
or
Satellite Brand:
Locate the brand name of your Cable Converter or Satellite in the "Setup
Codes For Cable Converters or Satellites" section. The brands are listed in
alphabetical order with the most popular codes listed first. You will use one
of these codes to program your Cinema 5 to operate your Cable Converter
or Satellite.
To program the Cinema 5 to operate your Cable Converter or Satellite:
1. Turn on your Cable Converter or Satellite.
2. Press CBL/SAT and release. Press and hold SETUP until
the Cinema 5 's red light blinks twice, then release
SETUP.
3. Enter the first four-digit Cable Converter or Satellite code
listed for your brand in the "Setup Codes For Cable
Converters or Satellites" section. If you perform this
procedure correctly, the red light will blink twice when you
enter the final digit of your code.
4. Aim the Cinema 5 at your Cable Converter or Satellite and
press POWER.Your Cable Converter or Satellite should
turn off. If your Cable Converter or Satellite does not
respond, repeat steps 2-4, trying each code listed for your
brand until you find the one that operates your Cable
Converter or Satellite.
5. Your Cinema 5 is now programmed to operate your
Cable Converter or Satellite. Write your Cable Converter or
Satellite code in the boxes to the left for future reference.
Remember, if you want to use your Cinema 5 to operate your Cable Converter
or Satellite, press the CBL/SAT key first.

SEARCHING FOR YOUR CODE

If your TV, VCR or Cable Converter does not respond to the Cinema 5 after
trying all of the codes listed for your brand, or if your brand is not listed at all, try
searching for your code. For example, after trying all of the codes for your TV,
you still cannot get the Cinema 5 to operate your TV, then:
1. Turn on your TV.
Press TV and release. Press and hold SETUP until the Big
2.
Easy HT 's red light blinks twice, then release SETUP.
9 - 9 - 1
9 - 9 - 1
3. Press 9 - 9 - 1.
4. Slowly alternate between pressing POWER* and TV until
your TV turns OFF. Make sure that the Cinema 5 is
aimed at your TV during the search. You may have to
press this sequence of buttons (POWER* then TV) up to
100 times to search the entire library of codes.
5. When your TV turns OFF, press and release SETUP to
lock in the code for your TV. Your Cinema 5 is now
programmed to operate your TV.
*If you are searching for your VCR, LD or DVD Player code, you may want to use
the PL (Play) key instead of the POWER key to search for your code. When your
VCR starts to play, press SETUP to lock in your code.
NOTE: To search for the codes of your other components, repeat Steps 1
through 4, only substitute the appropriate device key (VCR, DVD/LD, RCVR or
CBL/SAT) for the component you are searching for.
LEARNING THE CODES PROGRAMMED INTO THE Cinema 5
If you have set up the Cinema 5 using the "SEARCHING FOR YOUR CODE"
procedure, you may want to figure out which four-digit code is operating your
equipment. Use this procedure after you have set up your components to find
out which four-digit code is operating your equipment. For example, to find out
which code is operating your TV after setting up your TV using the "SEARCH-
ING FOR YOUR CODE" procedure:
1. Press TV and release. Press and hold SETUP until the Big
Easy HT 's red light blinks twice, then release SETUP.
9 - 9 - 0
2. 9 - 9 - 0 Press 9 - 9 - 0.
1
1
3. For the first digit of your four-digit code, press 1 and count
the number of times the red light (LED) blinks on the Big
Easy HT . If the light does not blink when you press the
number 1, the digit is zero.
2
2
4. For the second digit, press 2 and count the number of times the
red light (LED) blinks on the Cinema 5 . If the light does not blink
when you press the number 2, the digit is zero.
5. For the third digit, press 3 and count the number of times
3 the red light (LED) blinks on the Cinema 5 . If the light
3
does not blink when you press the number 3, the digit is
zero.
6. For the fourth and final digit, press 4 and count the number
4
4 of times the red light (LED) blinks on the Cinema 5 . If
the light does not blink when you press the number 4, the
digit is zero. Now you have your four-digit code.
NOTE: To find out the code for your other components, repeat Steps 1
through 6, only substitute the appropriate device key (VCR, DVD/LD, RCVR
or CBL/SAT) for the component code you wish to learn.