Installing The Batteries; Setting Up Your Components - One for All URC-5600 Cinema 5 User Manual

The SURROUND key operates the same as the Surround
On/Off key on your original remote. The SURROUND key
also controls the following functions in other modes: VCR
mode = Auto Tracking, DVD/LD mode = Disc, CBL/SAT
mode = Favorite Channel.
The MACRO key can memorize up to 15 keystrokes that
can be accessed in sequence with a single key press. The
key is not mode specific.

INSTALLING THE BATTERIES

Your Cinema 5 requires four (4) new AAA alkaline batteries. To install the
batteries:
On the back of the Cinema 5 , pull back on the tab and lift the
1.
battery cover off.
2. Match the + and - marks on the batteries to the + and -
marks in the battery case, then insert the batteries.
3. Press the battery cover back into place.
4. Test the unit by pressing POWER. If the batteries are
inserted correctly, the red light will blink.
NOTE: Removing the batteries will not require you to reprogram your remote
control because the Cinema 5 has unlimited memory backup.

SETTING UP YOUR COMPONENTS

Programming the Cinema 5 to operate your TV:
Locate the brand name of your TV and then write it in the space below.
TV Brand:
Locate the brand name of your TV in the "Setup Codes For TVs" section. The
brands are listed in alphabetical order with the most popular codes listed first.
You will use one of these codes to program your Cinema 5 to operate your TV.
To program the Cinema 5 to operate your TV:
1. Turn on your TV.
2. Press TV and release. Press and hold SETUP until the Big
Easy HT red light blinks twice, then release SETUP.
3. Enter the first four-digit TV code listed for your brand in the
"Setup Codes For TVs" section. If you perform this
procedure correctly, the red light will blink twice when you
enter the final digit of your code.
4. Aim the Cinema 5 at your TV and press POWER. Your TV
should turn off. If your TV does not respond, repeat steps 2-4,
trying each code listed for your brand until you find the one that
operates your TV.
Your Cinema 5 is now programmed to operate your TV. Write
5.
your TV code in the boxes to the left for future reference.
Remember, if you want to use your Cinema 5 to operate your TV, press the
TV key first.
Programming the Cinema 5 to operate your VCR:
Locate the brand name of your VCR and then write it in the space below.
VCR Brand:
Locate the brand name of your VCR in the "Setup Codes For VCRs" section. The
brands are listed in alphabetical order with the most popular codes listed first.
You will use one of these codes to program your Cinema 5 to operate your VCR.
To program the Cinema 5 to operate your VCR:
1. Turn on your VCR and insert a tape.
2. Press VCR and release. Press and hold SETUP until the
Cinema 5 red light blinks twice, then release SETUP.
3. Enter the first four-digit VCR code listed for your brand in
the "Setup Codes For VCRs" section. If you perform this
procedure correctly, the red light will blink twice when you
enter the final digit of your code.
Aim the Cinema 5 at your VCR and press POWER. Your
4.
VCR should turn off. If your original VCR remote control did
not have a POWER key, press PL (Play). Your VCR should
start to play. If your VCR does not respond, repeat steps 2-
4, trying each code listed for your brand until you find the
one that operates your VCR.
5. Your Cinema 5 is now programmed to operate your
VCR. Write your VCR code in the boxes to the left for
future reference.
Remember, if you want to use your Cinema 5 to operate your VCR, press the
VCR key first.
NOTE: If your TV/VCR is working on one of the codes highlighted with an
asterisk (*), you may need to program a separate TV code in order to control the
volume. Check the list of codes below and follow the instructions detailed in the
"Programming the Cinema 5 to Operate Your TV" section to program the
supplied TV code.
TV/VCRs working on VCR code 0032 may require
TV code 0000 for volume control.
TV/VCRs working on VCR code 0035 may require
TV code 0051 for volume control.
TV/VCRs working on VCR code 0048 may require
TV code 0093 for volume control.
TV/VCRs working on VCR code 0060 may require
TV code 0047 for volume control.
TV/VCRs working on VCR code 0081 may require
TV code 0054 for volume control.
TV/VCRs working on VCR code 0162 may require
TV code 0250 for volume control.
TV/VCRs working on VCR code 0278 may require
TV code 0451 for volume control.
Programming the Cinema 5 to operate your DVD or Laser Disc Player:
Locate the brand name of your DVD or Laser Disc Player and then write it in the
space below.
DVD/LD Brand:
Locate the brand name of your DVD or Laser Disc Player in the "Setup Codes
For DVD or Laser Disc Players" section. The brands are listed in alphabetical
order with the most popular codes listed first. You will use one of these codes to
program your Cinema 5 to operate your DVD or Laser Disc Player.
To program the Cinema 5 to operate your DVD or Laser Disc Player:
1. Turn on your DVD or Laser Disc Player and insert a disc.
2. Press DVD/LD and release. Press and hold SETUP until
the Cinema 5 's red light blinks twice, then release
SETUP.
3. Enter the first four-digit DVD or Laser Disc Player code
listed for your brand in the "Setup Codes For DVD or Laser
Disc Players" section. If you perform this procedure
correctly, the red light will blink twice when you enter the
final digit of your code.
4. Aim the Cinema 5 at your DVD or Laser Disc Player and
press POWER. Your DVD or Laser Disc Player should turn
off. If your DVD or Laser Disc Player does not respond,