Table of Contents
Advertisement
Section 2: Framing
In Wall and Corner Dimensions
1). Frame in the enclosure for the unit with framing materials. The
framed opening for the assembled fireplace shown below in table
NOTE: When constructing the framed opening, please ensure there is
access to install the gas line when the unit is installed
856
11
D
33
16 "
362
1
14
4 "
Figure 3.a Framing dimensions table
DRL*3613 DIMENSIONS
A
B
433/8
671/8
856
DRL60 Framing
11
33
16 "
The DRL60 comes standard
with a non-combustible steel
stud and a heat deflector. The
steel stud must be installed at
25" and the stud heat deflector
is mounted 3" unerneath the
361.950
combustible stud.
1
14
4 "
1751.076
15
68
16 "
DRL*6013 DIMENSIONS
A
6815/16
8
Framing header must
be turned on edge to
meet vent clearance
1101.100
3
A
43
8 "
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/32"
Drawn by
TWO PLACE DECIMAL
.015"
Revision / Date
C
D
THREE PLACE DECIMAL
.005"
A
ANGULAR
.5
Revision
ALL BENDS ARE ASSUMED
471/2
3311/16
553/8
TO BE 90 UNLESS NOTED
Finish
OTHERWISE.
26½" when
chase is
ventilated)
647.700
25
B
C
D
913/16
641/2
3311/16
DIMENSIONS ARE IN INCHES
NAME
DATE
TOLERANCES:
FRACTIONAL
1/32"
DM
03/09/2021
Drawn by
25½" to non-
TWO PLACE DECIMAL
.015"
THREE PLACE DECIMAL
.005"
Revision / Date
combustible
ANGULAR
.5
Revision
ALL BENDS ARE ASSUMED
header
TO BE 90 UNLESS NOTED
Finish
OTHERWISE.
* When sheetrock is used behind the fireplace, framing depth may be
increased by 1/2".
1206
C
1
47
2 "
NAME
DATE
Description
MNR36 Framing Assembly
DRL*4813 DIMENSIONS
DM
31/07/2018
DWG. NO.
MNR36 Framing Assembly
B
C
D
MATERIAL
791/4
561/16
3311/16
SCALE
1:32
WEIGHT:
26½" when
chase is
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN
ventilated)
COMBUSTIBLE
STUD
HEAT DEFLECTOR
NONCOMBUSTIBLE
STUD
When this appliance is installed directly on ANY combustible other
than wood flooring (carpet, vinyl, etc.). It must be installed on an
equivalent wood or metal panel. This material must extend the full
1
779.780
2 "
11
30
16 "
Description
Clearances must be in accordance with local installation codes and
MNR60-Framing Assembly
MNR60-Framing Assembly
DWG. NO.
MATERIAL
SCALE
1:24
WEIGHT:
SHEET 1 OF 2
Installation
12.700
1
2 "
12.700
1
2 "
1101.100
43
1705
67
Figure 3.b Framing dimensions (Straight wall & Corner Installation).
SHEET 1 OF 3
WARNING
width and depth of the appliance.
NOTICE
the requirements of the gas supplier
3
A
8 "
B
1
8 "
DIMENSIONS ARE IN INCHES
TOLERANCES:
Drawn by
FRACTIONAL
1/32"
TWO PLACE DECIMAL
.015"
Revision / Date
THREE PLACE DECIMAL
.005"
Revision
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
Finish
OTHERWISE.
XG0226 - 042220
NAME
DM
Advertisement
Table of Contents
