Advertisement
Quick Links
Advertisement
Related Manuals for NAKTO Elegance
Summary of Contents for NAKTO Elegance
- Page 1 Elegance...
- Page 2 Keep the spare fuse in a safe place.It is not used for assembly and will be used for the replacement if the original fuse were damaged. Ensure all the following pieces are included with the Nakto Elegance.
- Page 3 2.Now stand the bike upright. Place some foam padding under the front fork if placed on the ground or put it on bike assembly/repair stand if you have one. We want to keep your bike looking new! Step Two: Assemble the front wheel. 1.Loosen axle nuts on front wheel to make room for the front fork.
- Page 4 3.Lift the front of the bike and lower the fork onto the wheel. Notice: The axle should enter the fork dropouts fully. 4.Line up the axle lock washers (These are the metal washer with a bent tab on one side) with the hole at each fork. Notice: These two special fork lock washers keep the wheel from falling off...
- Page 5 6.Push the black plastic caps onto the axle nuts. 7.Put the brake cable back to the linkage of the left arm while squeezing the brake arms.
- Page 6 Step Three: Install the handlebar. 1.Insert the handlebar stem into the clamp. 2.Install the handlebar stem together with clamp onto the steer stem.
- Page 7 3.Set the stem to the desired height but not exceed max height or mini- mum insertion. 4.Align the stem so the handlebar is perpendicular to the front wheel. 5.Tighten the bolt at the clamp with the supplied allen wrench.
- Page 8 6.Perform a twist test. (1).Brace the front wheel between your legs. (2).Switch hands so the opposite hands are pushing and pulling with about 20 pounds of force make sure the handlebar and front wheel are still properly aligned. (3).Repeat the twist test pulling/pushing with the opposite hands...
- Page 9 Step Four: Install the front fender and headlight. 1.Remove the fender and headlight mounting bolt from the fork arch with the supplied screwdriver and set aside. 2.Place the fender in position. From the back of the front tire, pass the front fender mounting point under the front fork arch.
- Page 10 4.Attach the fender mounting arms to the front fork. Remove the mount- ing bolts from the fork. Pass the bolt through the arm mount and fork mounting point. Ensure the fender is centered and tighten both the mounting bolts. 5.Center the headlight and adjust the angle slightly downwards to illumi- nate the road ahead and not blind oncoming traffic.
- Page 11 Step Five: Adjust the front brake system. NOTICE: The adjustment of the front brake system is not easy. The following steps are only a general guide. If you are not sure you have the experience, skills, and tools to correctly perform all steps, consult a certified, reputable bike mechanic to assist with it.
- Page 12 Locate the pad to the top edge of the braking surface. Notice: Do not locate the pad to the top edge of the rim. It would hit the tire. Bring the pad gently to the rim and push with some mild force and secure the nut.
- Page 13 2.Cable Attachment. Before we draw the pads together, back out the barrel adjusters three or four turns. So that we can have some fine tuning at the lever. Loosen the pinch bolt.Pull the arms together with your hand and pull the cable out with some mild force.
- Page 14 3.Set Pad Clearance. Bring the barrel adjuster in toward the lever, giving more slack. Typically, the pads should feel like they are contacting the rotor at a minimum of 1/2 the lever travel. 4.Centering. Centering is done by subtle changes in spring tension. There are screws to the return spring on both sides.
- Page 15 Step Six: Install the seat. 1.Open the quick release lever by hinging it open fully. 2.Insert seat post into seat tube. Adjust the seat post up or down to a comfortable height, while ensuring the seat post is inserted into the frame past the minimum insertion point.
- Page 16 Step Seven: Install the pedals. 1. Locate the pedal with an “R” stamped into the end of the pedal axle, which indicate it is the right pedal. The right pedal goes on the crank on the right side of the bike. The remaining pedal with an “L” stamped into the end of the axle, is the left pedal.
- Page 17 2.The right pedal is threaded to tighten by turning clockwise. The left pedal is reverse-threaded and tightens counterclockwise. Carefully thread the pedal onto the crank by hand slowly. 3.Further tighten with the supplied double open end wrench. Do not cross thread or damage the threads.
- Page 18 Step Eight: Install the cushion. 1.Unlock the lock catch. 2.Put the cushion on the rear carrier. 3.Lock the lock catch.
- Page 19 Step Nine: Install basket. Notice: The basket may not arrive together with the Nakto ebike as it will be packed and dispatched separately. 1.Install bottom bracket (bracket 1). (1).Remove the axle nuts on front wheel with the supplied double open-end wrench and set aside.
- Page 20 (3).Tighten both axle nuts with the supplied double open-end wrench. (4).Once you have tightened both axle nuts push the black plastic caps onto the front axle nuts.
- Page 21 2. Fix the basket to the mount extending from the stem of handlebars. Pass the bolt through “bracket 2” mounting point, the top mounting point of the basket and the mount extending from the stem of handle- bars. Thread the lock nut onto the bolt end and tighten with the supplied screwdriver.
- Page 22 3. Fix the basket to the bottom bracket. Fit the bottom bracket into the curve of “bracket 4” . Pass the bolt through “bracket 3” mounting point, the basket bottom mounting point and “bracket 4” mounting point. Tighten with the supplied screwdriver.
- Page 23 4. Snap the cover into place. Step Ten: Inflate the tires. Check that the tire beads and tires are evenly seated around the rims. Use a pump with a Schrader valve and pressure gauge to inflate each tire to the recommended pressure indicated on the tire sidewall. Do not overin- flate or underinflate tires.
- Page 24 Operate the electrical system when the battery has been adequately charged and the battery is secured to the frame mount. Your Nakto bike comes partially charged. We recommend you Connect the charger input plug (110/220-volt plug) to the power outlet for 3 to 4 hours.
- Page 25 Torque Required Hardware Loca�on Hardware (Nm) All Fender Moun�ng Bolts and Fenders Hardware Headlight Angle Adjustment Headlight Bolt All Basket Moun�ng Bolts and Basket Area Hardware Seatpost Area Seat Angle Adjustment Bolt Rear Dropout Area Rear Axle Nuts Rear Dropout Area Rear Torque Arm Bolt Derailleur Hanger Moun�ng Rear Dropout Area...
- Page 26 Quick Start Guide This ebike is equipped with two ways for a rider to use power assistance from the motor to propel the bike forward: The pedal assist system (PAS) ⸺The rider can engage the pedal assist system (PAS) while pedaling, and it will call up assistance from the motor to help propel the bike forward.
- Page 27 2.Sit on the bike. 3.Turn on the electrical system⸺Press and hold the start button on LCD display panel for approximately 3 seconds until power is delivered to the LCD Display. 4.Turn on the headlight if needed or desired. Once the LCD Display is on, Press and hold “...
- Page 28 5.Select the desired level of pedal assistance⸺Select the level from 0-5 by pressing “ ︿ ” and “ ﹀ ” . Level 1 corresponds to the lowest level of pedal assistance, and level 5 corresponds to the highest level of pedal assistance.
- Page 29 7.The throttle is used by slowly and carefully rotating the throttle back- ward toward the rider. The more you twist, the more powerfully the throttle will propel the bike forward. Do not use the throttle while dismounted. Avoid accidental application of the throttle while dismounted;...
- Page 30 first ride. It is the user’ s responsibility to ensure a potential passenger on the Nakto eblike is adequately experienced and healthy enough to ride safely as a passenger. Serious injury or death can occur if passengers are inexperi- enced or in poor health such that it impacts their ability to ride as passen- gers safely.
- Page 31 ELECRTIC BICYCLE Trek Power Inc Toll Free: 1-855-997-7297 E-mail: support@nakto.com Website: www.nakto.com Adress:1683 Sierra Madre,Placentia,CA 92870...