Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for tams elektronik FCS-3
Summary of Contents for tams elektronik FCS-3
- Page 1 FCS-3 Busmodul für Faller* Car-System Bus module compatible to the Faller* Car-System Anleitung Module pour autobus du Faller* Car-System Manual Mode d´emploi Busmodule voor het Faller* Car System Handleiding Art.-Nr. 22-01-071-3...
- Page 2 © 07/2005 Tams Elektronik GmbH Alle Rechte, insbesondere das Recht der Vervielfältigung und Verbreitung sowie der Übersetzung vorbehalten. Vervielfältigungen und Reproduktionen jeglicher Form bedürfen schriftlichen Genehmigung durch die Tams Elektronik GmbH. Deutsch Technische Änderungen vorbehalten. English © 07/2005 Tams Elektronik GmbH All rights reserved.
-
Page 3: Table Of Contents
Technical specifications / Circuit Diagram(Fig. 1) Checking the package contents Required tools and materials Safe and correct soldering Special features of the additional components Mounting the FCS-3 Manufacturer's note Certification Conditional warranty Connections (Fig. 2) (Page II in the centre of this handbook is removeable.) -
Page 4: Intended Use
English FCS-3 Intended use Caution: Integrated circuits are very sensitive to static electricity. Do not touch components without first discharging yourself. Touching a radiator or other grounded metal part will discharge you. The module can be used according to the specifications of this manual in a vehicle compatible to the Faller* Car-System. - Page 5 FCS-3 English § Mounting the module should only be done in closed, clean, dry rooms. Beware of humidity. § Only use low power for this module as described in this manual and only use certified transformers. § Connect soldering irons only in approved mains sockets installed by an authorised electrician.
-
Page 6: Emc Declaration
English FCS-3 Dangerous environments A working area that is too small or cramped is unsuitable and can cause accidents, fires and injury. Prevent this by working in a clean, dry room with enough freedom of movement. Other dangers Children can cause any of the accidents mentioned above because they are inattentive and not responsible enough. -
Page 7: Summary Of Operation
FCS-3 English Summary of operation The module is particularly designed for the use in vehicles compatible to the Faller* car system, that are run with two accumulator batteries. It has six in- and outputs for the connection of LEDs, motor and reed contacts. -
Page 8: Technical Specifications / Circuit Diagram(Fig. 1)
English FCS-3 switched to „warning light“ until the drive on signal, but max. up to one minute. If the bus does not receive the signal to drive on during one minute, the flashing lights and the back lights are switched off (current saving mode). -
Page 9: Checking The Package Contents
FCS-3 English Fig. 1: Cicuit Diagram Checking the package contents Check the contents of the package for completeness after unpacking: § one module, § additional components: one resistor 10 kΩ, one diode 1N4148, one transistor BC 327, one reed-contact, §... -
Page 10: Safe And Correct Soldering
English FCS-3 Safe and correct soldering Caution: Incorrect soldering can cause dangers through fires and heat. Avoid these dangers by reading and following the directions given in the chapter Safety instructions. If you have had training in soldering you can skip this chapter. -
Page 11: Special Features Of The Additional Components
FCS-3 English Special features of the additional components Resistors Resistors reduce current. Their mounting orientation is of no importance. The value of resistors for smaller power ratings (under 5 W) is indicated through colour rings. Every colour stands for another figure. The added resistor has a value of 10 kΩ... -
Page 12: Mounting The Fcs-3
Sealed in the glass bulb are two or three reeds made of a magnetic material. When bending the legs the glass bulb they can be easily damaged through mechanical strain. Mounting the FCS-3 Preparation Open the housing of the vehicle. Locate the position for the module. - Page 13 FCS-3 English In order to check which one of the two connecting points of side B you have to connect to the module, connect temporarily the minus pole of the motor to the minus pole of the accumulator battery and the plus pole of the motor to one of the two connecting points at side B of the reed contact.
- Page 14 English FCS-3 Connection of the LEDs for the stop and back lights The two LEDs for the stop and back lights have to be connected in series, i.e. the anode (+) of the one LED has to be connected to the cathode (-) of the other LED.
-
Page 15: Faq
FCS-3 English § Parts are getting very hot and/or start to smoke. Disconnect the system from the mains immediately! Possible cause: The connections to the power supply are connected the wrong round. à Check the connection. In this case the module is probably damaged irreparably. -
Page 16: Conditional Warranty
English FCS-3 Conditions of warranty This product is guaranteed for two years. The warranty includes the correction of faults which can be proved to be due to material failure or factory flaw. We guarantee the function of the parts according to the... - Page 17 English FCS-3 Fig. 2: Connections Page II.1...
- Page 18 FCS-3 English Connection Table Connection to „-” of the accumulator batteries Connection to „+”of the accumulator batteries / front lighting Voltage output (-) of the circuit Motor control Right indicator Braking and reversing lights Left indicator Existing reed contact Secondary reed contact...
- Page 19 Actuele informatie en tips: http://www.tams-online.de Garantie und Service: Warranty and service: Garantie et service: Garantie en service: Tams Elektronik GmbH Rupsteinstraße 10 D-30625 Hannover fon: +49 (0)511 / 55 60 60 fax: +49 (0)511 / 55 61 61 e-mail: modellbahn@tams-online.de...