Advertisement
Quick Links
48in, 52in, or 60in E-Z Vac
2016 and After Grandstand
Model No. 78574—Serial No. 403300000 and Up
Model No. 78575—Serial No. 403300000 and Up
Model No. 78576—Serial No. 403300000 and Up
Note:
Install this kit to use with the E-Z Vac Twin Bagger; refer to the Operator's Manual for the bagger
for safety, operation, and maintenance procedures.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
1. Warning—read the Operator's Manual.
2. Warning—wear hearing protection.
3. Thrown object hazard—do not operate the machine without
the collection system installed and latched.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
136-4087
4. Cutting/dismemberment hazard of hand, impeller—stay away
5. Cutting/dismemberment hazard of hand, impeller—disengage
6. Warning; loss of traction hazard—do not operate with only the
Register at www.Toro.com.
™
Blower and Drive Kit
®
Mower
from moving parts; keep all guards and shields in place.
the PTO, remove the key, and wait for all moving parts to stop.
counterbalance weights installed; do not operate with only the
E-Z Vac installed; only operate with both the E-Z Vac and
counterbalance weights installed.
Original Instructions (EN)
All Rights Reserved *3435-383* A
Printed in the USA
Form No. 3435-383 Rev A
Installation Instructions
decal136-4087
Advertisement
Related Manuals for Toro E-Z Vac 78574
Summary of Contents for Toro E-Z Vac 78574
- Page 1 E-Z Vac installed; only operate with both the E-Z Vac and counterbalance weights installed. © 2019—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3435-383* A...
-
Page 2: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Remove the discharge chute and belt – No parts required cover. Blower mount Bolt (1/2 x 1-1/2 inches) Lock washer Nut (1/2 inch) Bolt (3/8 x 1-1/4 inches) -
Page 3: Preparing The Machine
Note: Determine the left and right sides of the machine from the normal operating position. Preparing the Machine No Parts Required Procedure Perform the following procedure to prepare the machine for attaching the blower and finishing kit. g037552 Disengage the PTO, move the motion-control Figure 1 levers to the N position, and set the... - Page 4 Installing the Pulley and Idler Assemblies For Machines with a Cast-Iron Spindle g194670 Figure 3 Parts needed for this procedure: 1. Nut (3/8 inch) 5. Bolt (1/2 x 1-1/2 inches) Blower mount 2. Blower mount 6. Lock washer Bolt (1/2 x 1-1/2 inches) 3.
- Page 5 Remove the nuts from the spindle in the right deck pulley and use them to attach the pulley assembly to the deck pulley (Figure Note: You may need to remove the mower belt to relieve the tension off the deck pulley when you install the pulley assembly.
- Page 6 Insert the pulley-plate mount studs into the holes in the sheave (Figure Installing the Pulley Assembly and Belt For Machines with an Aluminum Spindle Parts needed for this procedure: Pulley assembly Pulley-plate mount Flange nut (3/8 inch) Procedure Remove the top nut, washer, and sheave from g302390 the spindle (Figure...
- Page 7 Install the sheave assembly to the spindle using Align the new pulley assembly so that the the washer and top nut (Figure openings fit over the nuts (Figure 10). g302411 Figure 10 1. Pulley assembly 2. Nuts Turn the pulley to lock it into position (Figure 11).
- Page 8 Installing the Blower Assembly, Belt, and Belt Cover Parts needed for this procedure: Blower assembly Belt Belt cover Knob Procedure Refer to the bagger Operator’s Manual for the correct procedure to install the blower assembly, belt, and belt covers.