Operation Instructions; Lighting Instructions - Nexgrill 720-0882BF Operating Instruction

Outdoor gas grill
Hide thumbs Also See for 720-0882BF:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
GENERAL USE OF THE GRILL
Each main burner is rated at 2.64 kW. The main grill
burners encompass the entire cooking area and are side
ported to minimize blockage from falling grease and debris.
The knobs are located on the lower center portion of the
control panel. Each knob is labeled on the control panel.
USING THE GRILL
Grilling requires high heat for searing and proper browning.
Most foods are cooked at the
cooking time. However, when grilling large pieces of meat or
poultry, it may be necessary to turn the heat to the lower
setting after the initial browning. This cooks the food through
without burning the outside. Foods cooked for a long time or
foods basted with a sugary marinade may need the lower
heat setting near the end of the cooking time.
NOTE: This grill is designed to grill efficiently without the
use of lava rocks or briquettes of any kind. Heat is radiated
by the stainless steel flame tamers positioned above each
burner.
WARNING: IMPORTANT!
BEFORE LIGHTING
Inspect the gas supply hose prior to turning the gas "ON". If
there is evidence of cuts, wear, or abrasion, it must be
replaced prior to use. Do not use the grill if the odor of gas is
present. Only the pressure regulator and hose assembly
supplied with the unit should be used.
Never substitute regulators and hose assembly for those
supplied with the grill. If a replacement is necessary,contact
the manufacturer for proper replacement. The replacement
must be that specified in the manual.
Always keep your face and body as far away from the
burner as possible when lighting.
TO LIGHT THE MAIN BURNER
Make sure all knobs are OFF then turn on the gas supply
from the LPG (Liquid Petroleum Gasoline) tank. Always
keep your face and body as far from the grill as possible
when lighting.
To light your main burner, push and turn main burner
control knob to
, at the same time, press and hold
electronic ignition button to light the burner. Once the burner
is lit, release the electronic ignition button and knob. If the
burner does not light wait 5 minutes for any excess gas to
dissipate and then retry.
TO LIGHT THE SIDE SEARING BURNER
To light the side searing burner, remove any cooking
utensils from the burner grate. Push and turn thecontrol
knob to
, at the same time, press and hold electronic
ignition button to light the burner . Once the burner is lit,
release the electronic ignition button and knob. If the burner
does not light, turn the control knob to "○". If the smell of
gas is detected and the igniter is not functioning,
immediately turn the control knob "○". Allow 5 minutes for
any accumulated gas to dissipate. If the sear burner and
rear burner igniter are not functioning, see the following
section for match lighting.
heat setting for the entire
WARNING
Operating Instructions
NOTE: The hot grill sears the food, sealing in the juices.The
more thoroughly the grill is preheated, the faster the meat
browns and the darker the grill marks.
DO NOT LEAVE THE GRILL UNATTENDED WHILE
COOKING.
WARNING: IMPORTANT!
USING THE SIDE SEARING BURNER
Inspect the gas supply hose prior to turning the gas "ON". If
there is evidence of cuts, wear or abrasion, it must be
replaced prior to use. Do not use the side searing burner if
the odor of gas is present.
Keep a spray bottle of soapy water near the gas
supply valve and check the connections before each
use.
Do not attempt to light the grill if odor of gasis
present. Contact our customer service:
ServiceDK@nexgrill.com
Each burner is adjusted prior to shipment; however,
variations in the local gas supply may make minor
adjustments necessary.
Match Light
1. If the burner will not light after several attempts
then the burner can be match lit, before using the
match allow 5 minutes for any accumulated gas to
dissipate.
2. Clip a match on one end of the lighting rod.
3. Light match.
4. Hold lighting rod and insert lighted match right
next to the burner ports or ceramic file.
5. Push and turn the designated control knob to
6. Burner should ignite immediately.
10

Lighting Instructions

.

Advertisement

Table of Contents
loading

Table of Contents