Related Manuals for King Industrial KC-770FX
Summary of Contents for King Industrial KC-770FX
- Page 1 2” X 42” BELT & 8” DISC SANDER MODEL: KC-770FX INSTRUCTION MANUAL COPYRIGHT © 2022 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
-
Page 2: Warranty Information
WARRANTY INFORMATION 2-YEAR KING CANADA TOOLS LIMITED WARRANTY OFFERS A 2-YEAR LIMITED WARRANTY FOR THIS BELT AND DISC SANDER FOR NON-COMMERCIAL USE. PROOF OF PURCHASE Please keep your dated proof of purchase for warranty and servicing purposes. REPLACEMENT PARTS Replacement parts for this product are available at our authorized King Canada service centers across Canada. Please use the 10 digit part numbers listed in this manual for all part orders where applicable. - Page 3 SAFETY INSTRUCTIONS FOR YOUR BELT AND DISC SANDER SAFETY INSTRUCTIONS FOR BELT AND DISC SANDER • Sanding belt narrower than 1”. Narrower belts uncover parts that Safety is a combination of common sense, staying alert and knowing could trap your fingers, how your belt disc sander works.
- Page 4 SAFETY INSTRUCTIONS FOR YOUR BELT AND DISC SANDER USE THE RIGHT TOOL. Don’t force tool or attachment to do a job • NEVER use another person as a substitute for a table extension, or it was not designed to do. as additional support for a workpiece that is longer or wider than the basic sander table, or to help feed, support, or pull the workpiece.
-
Page 5: Electrical Information
ELECTRICAL INFORMATION WARNING ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE COMPRESSOR DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! POWER SUPPLY USING ON/OFF SWITCH WITH REMOVABLE SAFETY KEY WARNING: YOUR SANDER MUST BE CONNECTED TO A 120V WALL... -
Page 6: Getting To Know Your Belt & Disc Sander
8. 2” x 42” sanding belt (installed). 17. Rear disc table lock handle. 9. Belt tilting table. 18. Sanding disc dust chute (1-1/2”). SPECIFICATIONS Model ......................................KC-770FX Belt .................................... 1” x 42” & 2” x 42” Belt speed.................................... 3,100 SFPM Disc ........................................8” Disc speed....................................3450 RPM Motor ......................................6.2 Amp. - Page 7 ASSEMBLY UNPACKING Clean all rust protected surfaces with ordinary house hold type grease or spot remover. Do not use gasoline, paint thinner, mineral spirits, etc. These may damage painted surfaces. Apply a coat of paste wax to the tables to prevent rust. Wipe all parts thoroughly with a clean dry cloth.
-
Page 8: Assembly And Adjustments
ASSEMBLY & ADJUSTMENTS INSTALLING MITER GAUGE IN T-SLOT OF DISC TABLE 1. Slide the T-slot bar (A) Fig.7 of the miter gauge assembly (B) into one end of the T-slot (C) of the disc table (D). Note: The miter gauge can be used in either direction in the t-slot of the disc table, use the most effective direction depending on the operation. -
Page 9: Replacing Sanding Belt
ADJUSTMENTS REPLACING SANDING BELT WARNING!: Disconnect the power cord from the power source before attempting to replace a sanding belt. This belt & disc sander comes with a 2” x 42” sanding belt installed on the machine, and an additional 1” x 42” sanding belt (with 1” belt platen) is provided. To replace the 2”... -
Page 10: Replacing Sanding Disc
ADJUSTMENTS ADJUSTING BELT PLATEN (1” OR 2” BELT PLATENS) The belt platen (A) Fig.15 is used to support the workpiece against the sanding belt during operations. For most common operations using the sanding belt, belt platens (1” belt platen with 1” x 42” belt, 2” belt platen with 2” x 42” belt) must be adjusted so that it almost touches the back of the sanding belt. -
Page 11: Operation
OPERATION OPERATIONAL GUIDELINE FOR USING THIS BELT & DISC SANDER WARNING! FOR YOUR SAFETY AND TO REDUCE THE RISKS OF FIRE, THIS BELT & DISC SANDER SHOULD BE DEDICATED TO SANDING ONLY ONE MATERIAL (WOOD OR METAL). IF YOU DESIRE TO SAND WOOD AND METAL, IT IS EXTREMELY IMPORTANT THAT THE SANDING BELT AND SANDING DISC HOUSINGS BE COMPLETELY CLEANED OF ALL WOOD DUST OR METAL DUST BEFORE USING AGAIN. -
Page 12: Maintenance
OPERATION, MAINTENANCE & TROUBLESHOOTING OPERATION DUST COLLECTION It is strongly recommended to use a dust collection system when using this belt & disc sander. Use of a dust mask or respirator is still recommended, even when a dust collection system is in use. This belt &...