Table of Contents
Advertisement
EN
When the "safety switch off" function
has been triggered, a 0 is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
To reconnect the appliance, switch it
off by pressing the on/off key
then switch it on again.
Keep the control panel of the
heating areas clean and dry at all times.
In case of operating problems
or incidents not mentioned in this
manual, disconnect the appliance
and contact the SMEG technical
service.
Recommendation for the
good use of vitroceramic
hobs
* Use pots or pans with thick,
completely flat bottoms.
* Pans with a smaller diameter than
the shown heating area are not
recommended.
* Do not slide pots and pans over the
glass as they may scratch it.
* Although the glass can withstand
knocks from large pots and pans
without sharp edges, try not to
knock it.
* To prevent damage to the ceramic
glass induction surface, try not
to slide the pots and pans over
the glass, and keep the bottoms
of the vessels clean and in good
condition.
Try not to spill sugar or
products containing sugar on the
glass while the surface is hot as
these could damage it.
Cleaning and maintenance
To keep the appliance in good
condition, clean it using suitable
products and implements once it has
cooled down. This will make the job
easier and avoid the build-up of dirt
Never use harsh cleaning products or
tools that could scratch the surface, or
steam-operated equipment.
16
A pot or pan may become
stuck to the glass due to a product
having melted between them. Do
not try to lift the pot while the hot
plate is cold! This could cause the
glass break.
(1) and
Do not step on the glass or
lean on it as it could break and
cause injury. Do not use the glass
as a surface for putting objects.
SMEG reserves the right to make
changes to its manuals that it deems
necessary or useful, without affecting
the product's essential features.
Environmental
considerations
The symbol
or its packaging means that this
product cannot be treated like
ordinary household waste.This
product must be taken to a recycling
collection point for electrical and
electronic appliances. By ensuring
that this product is disposed of
correctly, you will avoid harming
the environment and public health,
which could happen if this product
is not handled properly. For more
detailed information about recycling
this product, please contact your
local authority, household waste
service or the store where you
purchased the product.
The packaging materials used are
environmentally-friendly and can
be recycled completely. Plastic
components are marked >PE<, LD<,
>EPS<, etc. Dispose packaging
materials, like household waste, in
your local container.
If something does not work
Before calling the technical service,
perform the verifications specified
below.
The appliance does not work:
Ensure that the power cable is plugged
in.
The pot sticks to the glass:
If there is molten material between
the pot and the glass, set the hot
plate to maximum power and try to
separate them.
Single Sensor Error :
If any of the sensors is active more
than 10 seconds, this error situation
occurs and error code"F1" is showed.
This error can be related with different
roots. One of them is that there may
be an object (fork, knife...) on the any
of the sensor.
Make sure that there is no any object
on the control unit, hob glass is wiped
with a dry cloth. If error situation
continue after this solution, please
take out plug or switch off fuse switch
for 10 second.
Plural Sensor Error:
If more than 2 sensors are sensed at
same time, this error situation occurs
on the product
and error code"F2" is displayed.
Potential root reasons of the
problem :
• There may be an object(pot...) or
water accumulation(overflow liquid
from pot...) that cover more than 2
sensors
• Touch control location may
exposure more heat or steam
(from oven bottom of the hob...)
Please be sure that there is no any
object on the sensors and switched off
all steam and heat sources. Then,hob
glass is wiped with a dry cloth. If error
situation continue after this solution,
please take out plug or switch off fuse
switch for 10 second.
FC Error:
Fc message on the control and the
hot plates switch off: Overheating
in the electronics. Let thestove cool
for a while.
Advertisement
Table of Contents
