Related Manuals for Planet IGS-6325-4T2X
Summary of Contents for Planet IGS-6325-4T2X
- Page 1 Industrial L3 Multi-Gigabit/10Gigabit Managed Ethernet Switch IGS-6325-4T2X/IGS-6325-5X1T Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ................. 3 2. Requirements ..................4 3. Wiring the Power Inputs ............... 5 3.1 Grounding the Device ..............6 4. Terminal Setup ..................7 4.1 Logging on to the Console .............. 8 4.2 Configuring IP Address via Console ..........9 4.3 Storing the current switch ............ -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET L3 Multi-Gigabit/10Gigabit Industrial Managed Switch, IGS-6325-4T2X/IGS-6325-5X1T. “Industrial Managed Switch” mentioned in this Quick Installation Guide refers to the above models. The descriptions of these models are shown below: Industrial L3 4-Port 2.5GBASE-T + 2-Port 10G SFP+ IGS-6325-4T2X Managed Ethernet Switch Industrial L3 5-Port 10GBASE-X SFP+ + 1-Port 10GBASE-T... -
Page 4: Requirements
2. Requirements Industrial Managed Switch provides remote login interface management purposes. The following equipment is necessary for further management: Workstations running Windows XP/2003/2008/Vista/7/8/10/11, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP Proto- cols. Workstations are installed with Ethernet NIC (Network Interface Card). -
Page 5: Wiring The Power Inputs
AC Input: 24V , 2A max. PWR1 Alarm PWR2 Figure 3-1: IGS-6325-5X1T Upper Panel Refer to the table below for the Input Voltage and Current values for each model. IGS-6325-4T2X IGS-6325-5X1T DC Input Voltage 9-48VDC 9-48VDC DC Max. Input Current AC Input Voltage 24VAC 24VAC AC Max. Input Current... -
Page 6: Grounding The Device
1. The wire gauge for the terminal block should be in the range from 12 to 24 AWG. 2. Please check the AWG Ampere specification before connecting PLANET Industrial Managed Switch. 3.1 Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. -
Page 7: Terminal Setup
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type serial (console) port of the Industrial Managed Switch. IGS Industrial Managed Switch PC/Workstation with Terminal Emulation Software RJ45 to DB9 RS232 Cable Console 115200,N,8,1... -
Page 8: Logging On To The Console
4.1 Logging on to the Console Once the terminal has been connected to the device, power on the Industrial Managed Switch and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown as follows as the login screen in Figure 4-1 appears. -
Page 9: Configuring Ip Address Via Console
4.2 Configuring IP Address via Console The Industrial Managed Switch is shipped with default IP address shown below: IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 To check the current IP address or assign a new IP address to the Switch, please use the procedure as follows: Display of the Current IP Address 1. At the “#”... -
Page 10: Storing The Current Switch
Figure 4-3: Configuring IP Address Screen 4. Enter “exit” command twice to return to the global configuration mode. 5. Repeat step 1 to check if the IP address has changed. 4.3 Storing the current switch 1. At the “#” prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 4-4: Saving Current Configuration If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. -
Page 11: Starting Web Management
5. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. - Page 12 2. When the following dialog box appears, please enter the default user name “admin” and password “admin” (or the password you have changed before) as shown in Figure 5-2. Default IP Address: 192.168.0.100 Default Username: admin Default Password: admin Figure 5-2: Login Screen 3. After entering the password, the main screen appears as shown in Figure 5-3.
- Page 13 The Switch Menu on the top of the Web page lets you access all the commands and statistics the Industrial Managed Switch provides. The Switch Menu always contains one or more buttons, such as “System”, “Switching”, “Routing”, “QoS”, “Security”, “Ring” and “Maintenance”. Figure 5-4: Switch Menu Figure 5-5: Switch Sub-menu Figure 5-6: Switch Sub-menu...
-
Page 14: Saving Configuration Via Web
If you are not familiar with Switch functions or the related para- meter, press “Help icon” anytime on the Web page to get the help description. 5.2 Saving Configuration via Web To save all applied and set the current configuration as a startup configuration, click the “Save” icon, then the startup configuration file will be loaded automatically across a system reboot. 1. Click the Save icon on the top Switch Menu bar. 2. -
Page 15: Restoring Default Configuration
Ring R.O. 2.5G 10G/1G 5G/100 2.5GBASE-T 10GBASE-T Console Console 115200,N,8,1 115200,N,8,1 Reset Button Reset Button Reset Reset 1G/2.5G LNK/ACT 10/100 LNK/ACT 1G/2.5G LNK/ACT LNK/ACT 2.5G LNK/ACT 10G/1G LNK/ACT IGS-6325-5X1T IGS-6325-4T2X Figure 6-1: Figure 6-2: IGS-6325-5X1T Reset Button IGS-6325-4T2X Reset Button... -
Page 16: Customer Support
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQs: https://www.planet.com.tw/en/support/faq Switch support team mail address: support@planet.com.tw Industrial User’s Manual: https://www.planet.com.tw/en/support/downloads?&method=keyword&keywo...