Related Manuals for Planet IGS-504HPT
Summary of Contents for Planet IGS-504HPT
- Page 1 Industrial Gigabit Switch With 4 Port 802.3at PoE+ IGS-504HPT / IGS-624HPT User's Manual...
-
Page 2: Fcc Warning
Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose. -
Page 3: Ce Mark Warning
Do not dispose of WEEE as unsorted municipal waste; they should be collected separately Revision User’s Manual of PLANET Industrial Gigabit Switch with 4-port 802.3at PoE+ For Model: IGS-504HPT / IGS-624HPT Revision: 1.1 (August, 2014) -
Page 4: Table Of Contents
Table Of Contents 1. Introduction ....................5 1.1 Package Contents ................5 1.2 How to Use This Manual............... 5 1.3 Product Features ................. 6 1.4 Product Specifications ................7 1.5 Physical Dimensions ................10 2. Installation ....................12 2.1 Product Description ................12 2.1.1 Switch Front Panel ..............13 2.1.2 LED Indicators ................14 2.1.3 Switch Upper Panel ..............15... -
Page 5: Introduction
Thank you for purchasing PLANET Industrial Gigabit Switch with 4-Port 802.3at PoE+, IGS-504HPT/IGS-624HPT. The descriptions of these models are as follows: IGS-504HPT : Industrial 5-Port Gigabit Switch with 4-Port 802.3at PoE+ (-40~75 degrees C) IGS-624HPT : Industrial 4-Port 10/100/1000T 802.3at PoE+ 2-Port 100/1000X SFP Ethernet Switch (-40~75 degrees C) In this user’s manual, the term “Industrial Gigabit PoE+ Switch”... -
Page 6: Product Features
PoE+ Switch. Appendix A This chapter contains cable information of the Industrial Gigabit PoE+ Switch. 1.3 Product Features Physical Port IGS-504HPT 5-Port 10/100/1000Base-T RJ45 with 4-Port IEEE 802.3af/802.3at PoE+ injector IGS-624HPT 4-Port 10/100/1000Base-T RJ45 with IEEE 802.3af/802.3at PoE+ Injector ... -
Page 7: Product Specifications
When Primary Port link fails, the traffic swaps to Backup Port automatically. Once the Primary Port status is connected, the traffic swaps from Backup Port to Primary Port 1.4 Product Specifications Model IGS-504HPT IGS-624HPT Hardware Specifications 5 x 10/100/1000Base-T 4 x 10/100/1000Base-T... - Page 8 Orange: PoE In-use 1 x LED for each mini-GBIC interface (IGS-624HPT Port-5 and Port-6): Green: LNK/ACT 1 x LED for Per copper port (IGS-504HPT): Green: 1000 LNK/ACT Orange: 100 LNK/ACT 4 x LED for PoE Power Usage (W): ...
- Page 9 Switch Specifications Switch Processing Scheme Store-and-Forward Address Table 1K entries Back pressure for half duplex Flow Control IEEE 802.3x pause frame for full duplex Switch fabric 10Gbps 12Gbps Throughput 7.44Mpps@64bytes 8.93Mpps@64bytes (packet per second) Maximum Transmit Unit 9216 bytes TP: 10/20Mbps, 100/200Mbps, 2000Mbps Speed SX/LX: 2000Mbps (full-duplex) FX: 200Mbps (full-duplex)
-
Page 10: Physical Dimensions
1.5 Physical Dimensions IGS-504HPT Industrial Gigabit PoE+ Switch dimensions (W x D x H): 161 x 107 x 72 mm 23.6 25.2 33.38... - Page 11 IGS-624HPT Industrial Gigabit PoE+ Switch dimensions (W x D x H): 161 x 107 x 72 mm 25.2 23.6 33.38 Industrial 802.3at PoE+ Gigabit Switch...
-
Page 12: Installation
Ethernet Plus (PoE+) that combine up to 30-watt power output and data per port over one Cat.5E / 6 Ethernet cable. With a total of up to 120 watts of PoE output capability, the IGS-504HPT and IGS- 624HPT are designed specifically to satisfy the growing demand of higher power consuming network PDs (powered devices) such as PTZ (Pan, Tilt &... -
Page 13: Switch Front Panel
2.1.1 Switch Front Panel Figure 2-1 shows the front panels of IGS-504HPT and IGS-624HPT Industrial Gigabit PoE+ Switches. Fiber Mode Switch Redundant Port 6 1000 Port 5 1000 P1 P2 FAULT LNK/ LNK/ 1000 LNK/ACT PoE In-Use PoE Power Usage (W) IGS-624HPT Figure 2-1: IGS-504HPT &... -
Page 14: Led Indicators
DIP Switch The front panel of the IGS-624HPT provides one 3-DIP Switch which is for configuring 100 or 1000X fiber support and fiber redundant function. Refer to the table below to know about the 3-DIP switch settings and descriptions: For more information about the fiber redundancy function, please refer to the chapter 2.1.7 Redundancy Overview. -
Page 15: Switch Upper Panel
100/1000Base-X SFP Interfaces (IGS-624HPT) Color Function Light: indicates the Switch is successfully connecting to the network at 100/1000Mbps. Blink: indicates that the Switch is actively sending or LNK/ACT Green receiving data over that port. OFF: indicates that the Switch is inactively sending or receiving data over that port. -
Page 16: Wiring The Power Inputs
2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Gigabit PoE+ Switch is used for two DC redundant powers input. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into contacts 1 and 2 for Power 1, or 5 and 6 for power. -
Page 17: Wiring The Faulty Alarm Contact
2.1.5 Wiring the Faulty Alarm Contact The faulty alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Gigabit PoE+ Switch will detect the fault status of the power failure, or port link failure (available for managed model) and then forms an open circuit. - Page 18 Transceiver Figure 2-3: Plug-in the SFP transceiver Approved PLANET SFP Transceivers PLANET Industrial Gigabit PoE+ Switch supports both single mode and multi-mode SFP transceivers. The following list of approved PLANET SFP transceivers is correct at the time of publication:...
- Page 19 Fast Ethernet Transceiver (100Base-X SFP) Speed Connector Wavelength Operating Model Fiber Mode Distance (Mbps) Interface (nm) Temp. MFB-FX Multi Mode 1310nm 0 ~ 60°C MFB-F20 Single Mode 20km 1310nm 0 ~ 60°C MFB-F40 Single Mode 40km 1310nm 0 ~ 60°C MFB-F60 Single Mode 60km...
- Page 20 MGB-TLB60 Mode 1550nm 1310nm It is recommended to use PLANET SFP transceivers on the Indus- trial Gigabit PoE+ Switch. If you insert an SFP transceiver that is not in the supported list, the Industrial Gigabit PoE+ Switch might Note not recognize it.
- Page 21 1000Base-SX/LX: Before connecting with switches, workstation or media converter, please do the following steps: 1. With 1000Base-X Fiber Speed, please set the DIP Switch of SFP Port 5 or Port 6 to the “OFF” position. Port 6 (DIP 2) 1000X 100FX Port 5 (DIP 1) 1000X...
- Page 22 3. Check whether the fiber-optic cable type matches with the SFP transceiver model. To connect to MFB-FX SFP transceiver, use the multi-mode fiber cable with one side being the male duplex LC connector type. To connect to MFB-F20/F40/F60/FA20/FB20 SFP transceiver, use the single- mode fiber cable with one side being the male duplex LC connector type.
-
Page 23: Redundancy Overview
2.1.7 Redundancy Overview The IGS-624HPT Industrial Gigabit PoE+ Switch provides rapid fiber redundancy of link for highly critical Ethernet applications. The redundant-mode supports auto-recover function. If the destination port of a packet is link down, it forwards the packet to the other port of the backup pair. The following figure shows the redundant function. -
Page 24: Mounting Installation
Please read the following topics and perform the procedures in the order being presented. In the installation steps below, this Manual uses IGS-801 (PLANET 8 Port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Gigabit PoE+ Switch are similar. - Page 25 Step 2: Lightly insert the bottom of the switch into the track Step 3: Check if the DIN-Rail is tightly on the track. Step 4: Please refer to the following procedures to remove the Industrial Gigabit Ethernet Switch from the track.
-
Page 26: Wall Mount Plate Mounting
Step 5: Lightly pull out the bottom of the switch for removing it from the track. 2.2.2 Wall-mount Plate Mounting To install the Industrial Gigabit Ethernet Switch on the wall, please follow the instructions described below. Step 1: To remove the DIN-Rail from the Industrial Gigabit Ethernet Switch, loosen the screws to remove the DIN-Rail. -
Page 27: Applications
3. Applications In this paragraph, we will describe how to install Industrial Gigabit PoE+ Switch and the installation points. Industrial Operating Environment 550m / 10km / 120km Control Center PoE+ PTZ Speed Dome Fiber Switch 1000 100m Data Power 1000Base-SX/LX Fiber-optic DC 48V 1000 IGS-624HPT... - Page 28 Installation Steps Step 1: Unpack the Industrial Gigabit PoE+ Switch. Step 2: Check whether the DIN-Rail is screwed on the Industrial Gigabit PoE+ Switch. (Please refer to DIN-Rail Mounting section for DIN-Rail installation, if the DIN-Rail is not screwed on the Industrial switch). If you want to wall-mount the Industrial Gigabit Ethernet Switch, please refer to Wall- mount Plate Mounting section for wall-mount plate installation.
-
Page 29: Switch Operation
4. Switch Operation 4.1 Address Table The Industrial Gigabit PoE+ Switch is implemented with an address table. This address table is composed of many entries. Each entry is used to store the address information of some nodes in network, including MAC address, port no., etc. -
Page 30: Auto-Negotiation
availability. However, the switch is most commonly used to segment existing hubs, which nearly always improves the overall performances. An Ethernet Switching can be easily configured in any Ethernet network environment to significantly boost bandwidth using the conventional cabling and adapters. Due to the learning function of the Industrial Gigabit PoE+ Switch, the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table. -
Page 31: Troubleshooting
Industrial Gigabit PoE+ Switch. Make sure the cable is installed properly. Make sure the cable is the right type. Turn off the power. After a while, turn on the power again. Why after my PoE PD device is connected to IGS-504HPT/IGS-624HPT, it cannot power on? Solution: 1. -
Page 32: Cable Connection Parameters
6. Cable Connection Parameters The wiring details are as shown below: 100FX Fiber Optical Cables: Standard Fiber Type Cable Specification Multi-mode 50/125μm or 62.5/125μm 100Base-FX (1310nm) Single-mode 9/125μm 100Base-BX-U (TX :1310/RX :1550nm) Single-mode 9/125μm 100Base-BX-D (TX :1550/RX :1310nm) 1000X Fiber Optical Cables: Standard Fiber Type Cable Specification... -
Page 33: Appendix A: Networking Connection
APPENDIX A: Networking Connection A.1 PoE RJ45 Port Pin Assignments (End-Span) PIN NO RJ45 POWER ASSIGNMENT • Power + 1 2 3 4 5 6 7 8 • Power + • Power - • Power - A.2 Switch’s RJ45 Pin Assignments 1000Mbps, 1000Base-T Contact MDI-X... -
Page 34: Rj45 Cable Pin Assignments
A.3 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable, and crossover cable connection: Straight Cable SIDE 1 SIDE 2 1 2 3 4 5 6 7 8... -
Page 35: Ec Declaration Of Conformity
*Type of Product : Industrial 4-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Ethernet Switch Industrial 5-Port Gigabit Switch w/ 4-Port 802.3at PoE+ *Model Number : IGS-624HPT, IGS-504HPT * Produced by: : Planet Technology Corp. Manufacturer Name Manufacturer Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)