1. Manuals
  2. Brands
  3. Planet Manuals
  4. Switch
  5. IGS-6325-20T4C4X
  6. Quick installation manual

Planet IGS-6325-20T4C4X Quick Installation Manual

Industrial rackmount l3 20-port managed ethernet switch
Hide thumbs Also See for IGS-6325-20T4C4X:
Table of Contents

Advertisement

Quick Links

Download this manual
Industrial L3 20-Port 10/100/1000T +
4-Port Gigabit TP/SFP + 4-Port 10G SFP+
Managed Ethernet Switch
IGS-6325-20T4C4X
Quick Installation Guide

Advertisement

Table of Contents
loading

Related Manuals for Planet IGS-6325-20T4C4X

Summary of Contents for Planet IGS-6325-20T4C4X

  • Page 1 Industrial L3 20-Port 10/100/1000T + 4-Port Gigabit TP/SFP + 4-Port 10G SFP+ Managed Ethernet Switch IGS-6325-20T4C4X Quick Installation Guide...

  • Page 2: Table Of Contents

    Table of Contents 1. Package Contents ..................3 2. Requirements ..................... 4 3. Wiring DC Power Inputs ................5 4. Terminal Setup ................... 6 4.1. Logging on to Console ................. 7 4.2. Configuring IP Address via Console ............8 5. Starting Web Management .................10 5.1 Logging in to the Industrial Managed Switch .........10 5.2. Saving Configuration via Web ..............13 6. Recovering Back to Default Configuration .............15...

  • Page 3: Package Contents

    1. Package Contents Thank you for purchasing PLANET Industrial L3 Managed Ethernet Switch. “Industrial Managed Switch” is used as an alternative name in this Quick Installation Guide. Open the box of the Industrial Managed Switch and carefully unpack it. The box...

  • Page 4: Requirements

    2. Requirements The Industrial Managed Switch provides remote login interface for management purposes. The following equipment is necessary for further management: z Workstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP Protocols. z Workstations are installed with Ethernet NIC (Network Interface Card) z Serial Port Connection (Terminal)  The above Workstations come with COM Port (DB9) or USB-to-RS232 converter.  The above Workstations have been installed with terminal emulator, such as Hyper Terminal included in Windows XP/2003, putty or Tera Term.

  • Page 5: Wiring Dc Power Inputs

    3. Wiring DC Power Inputs The 6-contact terminal block connector on the panel of Industrial Managed Switch is used for two DC redundant powers input. Please follow the steps below to insert the power wires. 1. Insert positive/negative DC power wires into contacts 1 and 2 for DC POWER 1, or 5 and 6 for DC POWER 2.

  • Page 6: Terminal Setup

    4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type of serial port of the Industrial Managed Switch. PC / Workstation with Terminal Emulation Software Managed Switch RS232 to RJ45 Cable Serial Port RJ45 Console Port Figure 4-1 Industrial Managed Switch Console Connectivity A terminal program is required to make the software connection to the Industrial Managed Switch.

  • Page 7: Logging On To Console

    4.1. Logging on to Console Once the terminal is connected to the device, power on the Industrial Managed Switch and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 4-3 appears.

  • Page 8: Configuring Ip Address Via Console

    To check the current IP address or modify a new IP address for the Switch, please use the procedures as follows:  Show the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. IGS-6325-20T4C4X # show ip interface brief 2. The screen displays the current IP address as shown in Figure 4-4. Figure 4-4: IP Information Screen  Configuring IP Address 3. At the “#” prompt, enter the following command and press <Enter> as shown in Figure 4-5.
  • Page 9 4. Repeat step 1 to check if the IP address is changed.  Store current switch configuration 5. Enter the following command and press <Enter> to go back to “#” prompt. # exit Figure 4-6: Inputting Exit Command Screen 6. At the “#” prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 4-7: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed Switch through the new IP address.

  • Page 10: Starting Web Management

    5. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address.
  • Page 11 Default Username: admin Default Password: admin Figure 5-2: Login Screen 3. After entering the password, the main screen appears as Figure 5-3 shows. Figure 5-3: Web Main Screen of Industrial Managed Switch...
  • Page 12 The Switch Main Menu is shown on top of the Web page, and the functions are shown on the left to configure the Industrial Managed Switch. Figure 5-4: Switch Menu Now, you can use the Web management interface to continue the Switch management or manage the Switch by console interface. Please refer to the user’s manual for more.

  • Page 13: Saving Configuration Via Web

    5.2. Saving Configuration via Web In the Industrial Managed Switch, the running configuration stores in the RAM. In the current version, the running configuration sequence of running-config can be saved from the RAM to FLASH by executing save startup config command, so that the running configuration sequence becomes the startup configuration file, which is called configuration save.
  • Page 14 2. Or you can press the “Save Configuration” button. Figure 5-7: Save Configuration Button 3. Press the “Save Configuration” button to save. Figure 5-8: Save Configuration...

  • Page 15: Recovering Back To Default Configuration

    10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx. IGS-6325-20T4C4X Console 1000 1000 10/100 Reset 115200, N, 8, 1 Figure 6-1: IGS-6325-20T4C4X Reset Button...

  • Page 16: Customer Support

    PLANET online FAQs: http://www.planet.com.tw/en/support/faq?method=category&c1=3 Switch support team mail address: support_switch@planet.com.tw IGS-6325-20T4C4X User’s Manual: https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=I GS-6325&view=3#list (Please select the suitable user’s manual from the list.) Copyright © PLANET Technology Corp. 2018. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

Table of Contents