Advertisement
COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your interior design requirements. Simply obtain a color conversion
kit of the appropriate color from your Leviton distributor and proceed as follows (please note that wallplate must be
removed).
1. Select the color of the face you desire.
2. The frame has snaps on its sides. Using a small screwdriver, gently remove the frame from the strap (refer to
Figure 2).
3. Take the new frame and position it properly to the strap. Notice that the frame has a cut-out for the air-gap
switch lever. Line up the plastic snaps with the square holes in the strap. Insert the snaps on one side of the
frame into the strap.
4. Firmly press sideways and down to slip the other snaps into place. The frame snaps in with a audible click.
®
Ensure that all four snaps are secure. Replace Decora
wallplate. The color conversion is complete.
Figure 2 – Color Conversion
Brightness Level Display
Snaps
Push in 2 Locations
Air-Gap
Switch
TO PROGRAM
Programming scenes occurs at the Scene Controller for this dimmer. If programming is required, refer to Scene
Controller's instruction sheet.
OPERATION
ON:
Tap the upper half of the rocker. The lights will brighten to the last set light level.
OFF:
Tap the lower half of the rocker. The lights will dim to OFF.
BRIGHTEN:
Press and hold the upper half of the rocker to the desired light level.
FULL BRIGHT: If the lights are OFF, double tap the upper half of the rocker. The lights will turn ON FULL
BRIGHT.
If the lights are ON, tap the upper half of the rocker once. The lights will turn ON FULL
BRIGHT.
The previous light level will remain in memory upon next ON operation (see above).
FAST OFF:
Double tap the bottom half of the rocker. The lights will immediately turn OFF.
DIM:
Press and hold the lower half of the rocker to the desired level.
BRIGHTNESS LEVEL DISPLAY:
Indicates the level of brightness when the lights are ON. Indicates the previous level of brightness when the lights are
OFF (refer to Figure 1).
NOTE: To alert you that there is power to the dimmer when the load is OFF, the ON/OFF LED remains ON. To alert
you that the load is ON, the ON/OFF LED remains OFF.
NOTE: If lights are OFF, regardless if you tap or press and hold the upper half of the rocker, the lights will go to
last set light level.
NOTE: If a power interruption should occur while the device is ON, the light load will return to its previous light level
when power is restored within 10 seconds.
TROUBLESHOOTING
• Light does not turn ON and ON/OFF LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp switch is OFF, if applicable.
- Lamp is burned out.
- Lamp is not connected to line Neutral.
- Air gap switch is open.
• Dimmer does not operate
- Dimmer BLACK wire miswired to lamp and Dimmer BLUE wire miswired to LINE Hot.
• Light turns ON and Dimmer works, but Controller does not work
- There are no connections from Controller to Dimmer (YELLOW
- Controller is miswired.
• Lights Flickering
- Lamp has a bad connection.
- Lamp load is less than 60W or 60VA.
PK-93080-10-00-0A
2
Frame
ON/OFF
LED
Strap
120VAC, 60Hz
wire).
PK-93080-10-00-0A
Wiring Diagram 1 – Two Location Control Application
Scene Controller
Scene Capable
Dimmer
Hot (Black)
Black
Blue
Black
Black
Yellow
Yellow
Line
White
White
Load
120VAC, 60Hz
Green
Ground
White
Neutral (White)
Wiring Diagram 2 – Scene Dimming: Low-Voltage and Line Voltage with
Multiple Scene Controllers and Scene Dimmers
Scene
Scene
Scene Capable Dimmer
Scene Capable Dimmer
Controller
Controller
(Low-Voltage)
Hot (Black)
Black
Black
Black
Black
Blue
Yellow
Yellow
Yellow
White
White
White
Green
Line
Ground
LOAD
Neutral (White)
Wiring Diagram 3 – Scene Dimming: Line Voltage with
Multiple Scene Controllers and Dimmer on Two Circuits
Scene
17100-2WY
Scene
Scene
Dimmer
REPEATER
Dimmer
Controller
(Incandescent)
2-Way
(Incandescent)
Line B
120VAC, 60Hz
Line A
Black Yellow
Black
Black
Yellow
Black
Circuit A Circuit B
Yellow
Black
Red
Yellow
Yellow/Red
White
Gray
Green
Green
Ground
Ground
Blue
Blue
White
Load
Load
Neutral A
Neutral B
Wiring Diagram 4 – Scene Dimming: Low-Voltage and Line Voltage with
Multiple Scene Controllers and Dimmer on Two Circuits
Scene
17100-2WY
Dimmer
Scene
Scene Dimmer
REPEATER
(Incandescent)
Controller
2-Way
(Low-Voltage)
Line B
120VAC, 60Hz
Line A
Black Yellow
Black
Yellow
Circuit A Circuit B
Black
Yellow
Black
Red
Yellow
Yellow/Red
White
Gray
White
Green
Green
Ground
Ground
Blue
Blue
White
Load
LOAD
Neutral A
Neutral B
9/24/02, 1:52 PM
(OR PRIMARY SIDE OF
MAGNETIC LOW-VOLTAGE
TRANSFORMER)
}
(Incandescent)
Blue
Black
Load
Green
Ground
White
Scene
Controller
Yellow
White
Scene
Controller
Black
Yellow
White
Advertisement
