Related Manuals for HP S5830V2 Series
Summary of Contents for HP S5830V2 Series
- Page 1 H3C S5830V2 & S5820V2 Switch Series EVB Command Reference Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Software version: Release 22xx Document version: 6W100-20131105...
- Page 2 Copyright © 2013, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. Trademarks H3C, , Aolynk,...
- Page 3 Preface The H3C S5830V2 & S5820V2 documentation set includes 14 command references, which describe the commands and command syntax options available for the H3C S5830V2 & S5820V2 Switch Series. The EVB Command Reference describes the EVB configuration commands. This preface includes: •...
- Page 4 Conventions This section describes the conventions used in this documentation set. Command conventions Convention Description Boldface Bold text represents commands and keywords that you enter literally as shown. Italic Italic text represents arguments that you replace with actual values. Square brackets enclose syntax choices (keywords or arguments) that are optional. Braces enclose a set of required syntax choices separated by vertical bars, from which { x | y | ...
- Page 5 About the H3C S5830V2 & S5820V2 documentation set The H3C S5830V2&S5820V2 documentation set includes: Category Documents Purposes Compliance and safety Provides regulatory information and the safety manual instructions that must be followed during installation. Installation quick start Provides basic installation instructions. Provides a complete guide to hardware installation Installation guide and hardware specifications.
- Page 6 We appreciate your comments.
-
Page 7: Table Of Contents
Contents EVB commands ····························································································································································· 1 description ································································································································································· 1 display evb cdcp ······················································································································································ 1 display evb evb-tlv ···················································································································································· 2 display evb s-channel ··············································································································································· 4 display evb summary ··············································································································································· 5 display evb vsi ·························································································································································· 5 display interface s-channel ······································································································································... -
Page 8: Evb Commands
EVB commands description Use description to configure a description for an interface. Use undo description to restore the default. Syntax description text undo description Default The default description for an interface is "interface name Interface." For example, the default description for S-channel interface S-channel 1/0/1:10 is S-channel 1/0/1:10 Interface. -
Page 9: Display Evb Evb-Tlv
network-operator Parameters interface interface-type interface-number: Specifies a port by its type and number. If no interface is specified, the command displays CDCP negotiation information for all ports with EVB enabled. Examples # Display CDCP negotiation information for all ports with EVB enabled. <Sysname>... - Page 10 Examples # Display EVB TLV negotiation information for Ten-GigabitEthernet 1/0/1. <Sysname> display evb evb-tlv interface ten-gigabitethernet 1/0/1 S-Channel1/0/1:1 EVB mode : Local-bridge/Remote-station BGID status : Not supported Local RR capability : Supported Local RR status : Disabled Remote SGID status : Not supported Remote RR request status : Not requested...
-
Page 11: Display Evb S-Channel
Field Description Maximum ECP retransmission times in this format: Local negotiation value/Remote negotiation value/Operative value. Max ECP retry time NA means no value is set on the remote EVB station. ECP retransmission exponent in this format: Local negotiation value/Remote negotiation value/Operative value. ULPPDU retransmission exponent NA means no value is set on the remote EVB station. -
Page 12: Display Evb Summary
Field Description VSI number Number of VSIs created on the S-channel. display evb summary Use display evb summary to display the EVB summary. Syntax display evb summary Views Any view Predefined user roles network-admin network-operator Examples # Display the EVB summary. <Sysname>... - Page 13 Parameters verbose: Displays detailed VSI information. Without this keyword, the command displays brief VSI information. interface interface-type interface-number: Specifies a port by its type and number. If no interface is specified, the command displays VSI information for all ports with EVB enabled. Examples # Display brief VSI information for Ten-GigabitEthernet 1/0/1.
-
Page 14: Display Interface S-Channel
Field Description Address of the VSI manager. VSI manager ID NA indicates no VSI manager is specified. VSI filter type: • VLAN ID. Filter type • MAC address/VLAN ID. VSI filters: • In the format <VLAN ID>, meaning the VLAN to which the traffic belongs. Filter info •... - Page 15 Description: S-Channel1/0/1:10 Interface 10Gbps-speed mode, full-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation PVID: 1 Port link-type: access Tagged Vlan: none UnTagged Vlan: 1 Last clearing of counters: Never # Display brief information about S-channel interface S-channel 1/0/1:10. Assume that you have configured a description for the interface as 1234567890123456789012345678901234567890.
-
Page 16: Evb Default-Manager
The brief information of interface(s) under bridge mode: Link: ADM - administratively down; Stby - standby Speed or Duplex: (a)/A - auto; H - half; F - full Type: A - access; T - trunk; H - hybrid Interface Link Speed Duplex Type PVID Description SCH1/0/1:10.1 12345678901234567890123456789... -
Page 17: Evb Enable
Syntax evb default-manager { { ip ip-address | ipv6 ipv6-address | name name } [ port port-number ] | local-server } undo evb default-manager Default The default VSI manager is not specified. Views System view Predefined user roles network-admin Parameters ip ip-address: Specifies the IPv4 address of the default VSI manager. -
Page 18: Evb Mac-Learning Forbidden
Predefined user roles network-admin Usage guidelines After you enable EVB on the bridge port, the device cannot forward the data received from the port • at Layer 3. • Do not enable EVB on a member port of an aggregation group. Restore all default settings for a port before enabling EVB on the port. -
Page 19: Evb Reflective-Relay
Examples # Disable the MAC address learning function for S-channel 1/0/1:10. <Sysname> system-view [Sysname] interface s-channel 1/0/1:10 [Sysname-S-Channel1/0/1:10] evb mac-learning forbidden Related commands evb reflective-relay evb reflective-relay Use evb reflective-relay to enable the RR mode for an S-channel. Use undo evb reflective-relay to disable the RR mode for an S-channel. Syntax evb reflective-relay undo evb reflective-relay... -
Page 20: Evb Vdp Timer Keepalive Exponent
Default Only an automatically created default S-channel, with both SCID and SVID as 1, exists on a port with EVB enabled. Views Ethernet interface view Predefined user roles network-admin Parameters channel-id: Specifies an S-channel ID (SCID) in the range of 2 to 167. 0 is the reserved SCID, and 1 is the default SCID. - Page 21 Default The VDP keepalive exponent is 20. Views Ethernet interface view Predefined user roles network-admin Parameters value: Specifies a VDP keepalive exponent in the range of 14 to 31. Usage guidelines The value for VDP keepalive time is expressed by the following equation: VDP keepalive time (seconds) = 1.5 ×...
-
Page 22: Evb Vdp Timer Resource-Wait-Delay Exponent
Examples # Configure the VDP keepalive exponent for Ten-GigabitEthernet 1/0/1 as 23. <Sysname> system-view [Sysname] interface ten-gigabitethernet 1/0/1 [Sysname-Ten-GigabitEthernet1/0/1] evb vdp timer keepalive exponent 23 evb vdp timer resource-wait-delay exponent Use evb vdp timer resource-wait-delay exponent to configure a VDP resource-wait-delay exponent. Use undo evb vdp timer resource-wait-delay exponent to restore the default. -
Page 23: Evb Vsi
VDP resource-wait-delay exponent Calculated value (seconds) Result value (seconds) 671.08864 1342.17728 1343 2684.35456 2685 5368.70912 5369 10737.41824 10738 21474.83648 21475 Examples # Configure the VDP resource-wait-delay exponent for Ten-GigabitEthernet 1/0/1 as 23. <Sysname> system-view [Sysname] interface ten-gigabitethernet 1/0/1 [Sysname-Ten-GigabitEthernet1/0/1] evb vdp timer resource-wait-delay exponent 23 evb vsi Use evb vsi to create a VSI. -
Page 24: Evb Vsi Active
and the traffic from the VM cannot be forwarded. When you change pre-association to association for a VSI, the EVB bridge sets the VM's MAC address. After creating a VSI, you can enter VSI view by executing the interface s-channel command. •... -
Page 25: Evb Vsi Filter
evb vsi filter Use evb vsi filter to configure a VSI filter. Use undo evb vsi filter to remove a VSI filter. Syntax evb vsi filter vlan vlan-id [ mac mac-address ] undo evb vsi filter [ vlan vlan-id [ mac mac-address ] ] Default No VSI filter exists. -
Page 26: Reset Counters Interface S-Channel
Syntax interface s-channel { interface-number:channel-id | interface-number:channel-id.vsi-local-id } Views System view Predefined user roles network-admin Parameters interface-number:channel-id: Specifies an S-channel interface. The interface-number argument specifies the physical port where the S-channel resides. The channel-id argument specifies the ID of the S-channel. This S-channel ID must exist. - Page 27 Usage guidelines To collect traffic statistics for an S-channel interface or a VSI in a certain period, use this command • to clear existing statistics for the interface. If no parameters are specified, the command clears statistics for all interfaces. •...
-
Page 28: Index
Index D E I R reflective-relay,12 s-channel,12 description,1 evb vdp timer keepalive exponent,13 display evb cdcp,1 evb vdp timer resource-wait-delay exponent,15 display evb evb-tlv,2 vsi,16 display evb s-channel,4 evb vsi active,17 display evb summary,5 evb vsi filter,18 display evb vsi,5 display interface s-channel,7 interface...