Smart Au Totest Ing; Smart Prior In Tru Sion At Tempt Alert - Clifford cyber Arrow 3 Owner's Manual

Clifford arrow 3 complete owner's manual

Owner's manual (16 pages)

Table of Contents

Each time you remotely arm the system, it tests all triggers and sensors. If the hood or trunk is open, the system will immediately sound 4 chirps and 4

indicator light flashes instead of the usual 2 and 2. If a door is ajar, you'll receive 2 chirps and 2 flashes, then, 5 seconds later, there will be 4 chirps and 4

flashes. If a sensor is malfunctioning, you will receive the usual 2 chirps and 2 flashes, then, 10 seconds later, there will be 4 chirps and 4 flashes.

NOTE: Since this is a warn ing in di ca tion, you will hear the 4 chirps even if you use the chirp mut ing fea ture.

Specific malfunction identification:

4-chirp/4-flash signal upon arming, perform the following to identify the malfunctioning trigger or sensor:

1. Remotely disarm, then turn on the ignition. The LED status indicator inside your vehicle will be flashing, pause, then repeat.

2. Count the number of flashes in one cycle between pauses (for your convenience, the flash cycle repeats a total of 5 times) and refer to the chart below:

LED flashes

1 flash

Activation of optional sensor

2 flashes

Activation of Piezo Sensor

4 flashes*

Door open/ajar

5 flashes

Trunk/hood open/ajar (trunk only if you have the IntelliStart 4 option)

6 flashes

Hood open/ajar (only if you have the IntelliStart 4 option)

7 flashes

Ignition switch was turned on while the system was armed

8 flashes

Three or more incorrect valet codes were entered

10 flashes

Power tampering or the vehicle battery is very low

* If your ve hi cle has a factory- installed fea ture that turns off or dims the in te rior cour tesy lights sev eral sec onds af ter you exit the ve hi cle, the sys tem can not pro vide this in di ca tion.

The system automatically bypasses any faulty point and arms all other triggers and sensors for the utmost possible protection. If you accidentally arm with

the hood, trunk or a door open, just close it (no need to disarm-and-rearm) and the system will again monitor that point.

If you hear three chirps when you disarm, it means that a trigger or sensor was activated in your absence. When you turn on the ignition, the LED will flash 1-8

times, pause, then repeat the flash cycle 4 more times. Count the flashes in one cycle and refer to the chart above.

The system's memory records the identity of the last eight activated or malfunctioning triggers and sensors, which allows your installer to instantly track down

malfunctions. To identify the triggers and sensors held in the system's memory, use the following procedure:

1. Remotely arm and disarm while pressing the blank button on the PlainView 2 switch.

2. The LED will flash 1-10 times to indicate the most recently activated point, pause, flash 1-10 times to indicate the second most recently activated

point, and so on.

3. Write down the number of flashes between pauses and refer to the chart above.

With the optional CliffNet Wizard, you'll see this chronological report right on screen.

If power is removed, SmartPowerUp 2 ensures the system automatically restores itself to its previous state when power is restored. So if a thief disconnects

the power and then restores it in an attempt to start the car, the system will re-arm and instantly sound the siren while continuing to immobilize the

starter. If your vehicle is to be serviced by a mechanic, just put the system in valet mode. If the mechanic needs to interrupt power, your system will

automatically return to its valet mode state when power is restored; there will be no alarm activation.

If you opted to have the Clifford DataPort interface connector installed with your system, you can use our CliffNet Wizard software to access your system

through your Windows PC. CliffNet Wizard will show you, on your PC screen, all your user-programmable feature settings. You can change settings

simply by mouse-clicking the graphical button for each feature. You can customize features, add or delete remote controls, change remote control button

assignments, view a chronological history of trigger and sensor activations, and much more. It's actually fun! And secure. To learn more and download

this free software, go to www.clifford.com/wizard.