Page 3
If a problem continues even after performing all troubleshooting and technical tips, report the problem to the appropriate Toshiba service center along with the following information. This information will help the service center understand your problem and take quick action to find the solution.
Page 156
P.11-9 "11.2 Firmware Updating with USB Media" When the function of the Data Overwrite Enabler (GP-1070) is deleted from the equipment, the service call “F200” occurs. [F350] SLG board abnormality (e-STUDIO556/656/756/856) / SYS board abnormality (e- STUDIO557/657/757/857) Classification Error item...
Page 268
Input check (Test mode 03) [FAX] button: OFF / [COPY] button: OFF ([FAX] LED: OFF / [COPY] LED: OFF) Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Intermediate transport sensor No paper Paper present 1st drawer transport sensor No paper Paper present 1st drawer feed sensor...
Page 269
Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Bypass paper size detection sensor-3 Other than A3/LD A3/LD (Refer to Table 1) Bypass paper size detection sensor-2 Other than A4-R/LT- A4-R/LT-R (Refer to Table 1) Bypass paper size detection sensor-1 Other than A5-R/ST- A5-R/ST-R (Refer to Table 1)
Page 270
Table 1. Relation between the status of the bypass paper size detection sensor and the paper width Bypass paper-width sensor Paper-width size A3/LD A4-R/LT-R A5-R/ST-R Card size B4/LG B5-R e-STUIDIO556/656/756/856...
Page 271
[FAX] button: ON / [COPY] button: OFF ([FAX] LED: ON / [COPY] LED: OFF) Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Exit sensor Paper present No paper Cover interlock switch (front cover (lower)) Door closed Door opened Toner bag full detection sensor Full...
Page 272
Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Original tray sensor Original present No original Original empty sensor Original present No original Jam access cover opening/closing sensor Cover opened Cover closed RADF opening/closing sensor RADF opened RADF closed Original exit sensor Original present...
Page 273
[FAX] button: OFF / [COPY] button: ON ([FAX] LED: OFF / [COPY] LED: ON) Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Temperature/humidity sensor (displays Temperature [°C] temperature inside of the equipment) Temperature/humidity sensor (displays humidity Humidity [%RH] inside of the equipment) Drum thermistor (displays drum surface...
Page 274
Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. USB Dongle for Printer/Scanner Kit (GM-2270) Connectable (*2) Not connectable USB Dongle for Printer Kit (GM-1250) Connectable Not connectable USB Dongle for Scanner Kit (GM-4250) Connectable Not connectable Dongles for other equipments / Other USB Connectable Not connectable...
Page 275
Output check (test mode 03) Code Function Code Function Procedure Drum motor ON (operational without Code No. 101 function OFF developer unit) New toner supply motor ON Code No. 102 function OFF (operational with developer unit) Polygonal motor (600 dpi) ON Code No.
Page 276
Code Function Procedure 1st drawer feed clutch ON/OFF 2nd drawer feed clutch ON/OFF Bypass feed clutch ON/OFF Tandem LCF pickup solenoid ON/OFF Tandem LCF end fence reciprocating movement Tandem LCF end fence motor ON/OFF 3rd drawer / Tandem LCF feed clutch (Tandem LCF model) ON/OFF 3rd drawer / Tandem LCF transport clutch ON/OFF Key copy counter count-up Horizontal transport section drive clutch-2 ON/OFF...
Page 277
Code Function Procedure RADF original feed motor ON/OFF (normal rotation) RADF original feed motor ON/OFF (reverse rotation) RADF read motor ON/OFF RADF original exit motor ON/OFF (normal rotation) RADF original exit motor ON/OFF (reverse rotation) RADF original reverse motor (normal rotation) ON/OFF RADF original reverse motor (reverse rotation) ON/OFF RADF original reverse solenoid ON/OFF Laser unit cooling fan (high speed) ON/OFF...
Page 278
Test print mode (test mode 04) Code Types of test pattern Remarks Output for Secondary scanning direction 17 gradation Error diffusion / gamma adjustment steps pattern Grid pattern Pattern width: 2 dots, Pitch: 10 mm e-STUIDIO556/656/756/856...
Page 279
4: Sensor LED off-level abnormality or sensor LED light amount abnormality Adjustmen Process Image 2134 Sensor output value 0-1023 Displays a sensor output value when the light source of t mode quality when LED light the LED is OFF. control source is OFF e-STUDIO556/656/756/856...
Page 280
Drum surface 0-999 The measured value of the residual voltage after t mode quality potential sensor/ discharging is displayed. control Residual voltage * The normal range of this code is "400 to 800" after sensor output(Latest performing 05-2188. value) e-STUDIO556/656/756/856...
Page 281
Refer to 0-255 When the value increases, the laser power output t mode quality adjustment contents increases. control <Default value> e-STUDIO556/656: 132 e-STUDIO756/856: 101 Adjustmen Process Image Laser power 2250 2nd laser 0-255 When the value increases, the laser power output...
Page 282
0.2 mm. Adjustmen Scanner Scanner 3046 Carriage position 0-255 SYS When the value increases by "1", the carriage position t mode adjustment during shifts by approx. 0.1 mm toward the exit side when scanning from RADF using the RADF. (black) e-STUDIO556/656/756/856...
Page 283
When the value increases in increments of "1", the t mode polygonal motor scanning direction reproduction ratio of the primary scanning direction rotation speed reproduction ratio increases as follows: e-STUDIO556/656: 0.3 mm/step e-STUDIO756/856: 0.1 mm/step Adjustmen Printer Printer Fine adjustment of Adjustment of primary 4001 0-255 When the value increases in increments of "1", the...
Page 284
When the value increases by "1", the writing start t mode writing start position direction contents position shifts to the front side by approx. 0.0423 mm. <Default value> e-STUDIO556/656: 113 e-STUDIO756/856: 123 Adjustmen Printer Image Adjustment of drawer 4018 1st drawer 0-255 When the value increases by "1", the image shifts...
Page 285
Adjustmen Printer Image Leading edge position 4063 Option LCF 0-40 When the value increases by "1", the image shifts t mode adjustment toward the trailing edge of the paper by approx.0.4 mm. e-STUDIO556/656/756/856...
Page 286
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 287
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 288
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size1 increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 289
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size2 increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 290
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size3 increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 291
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size increases by approx.0.8 mm. <Paper length>Long size:330 mm or longerMiddle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 292
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size increases by approx.0.8 mm. <Paper length>Long size:330 mm or longerMiddle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 293
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size1 increases by approx.0.8 mm.<Paper length>Long size:330 mm or longer,Middle size:220 mm to 329 transport mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 294
Paper pushing 4112 OHP film 0-63 When the value increases by "1", the drive count of the t mode feeding amount adjustment bypass feed roller (at the start of the paper transport from the registration section) increases approx. 2 ms. e-STUDIO556/656/756/856...
Page 295
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 296
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 297
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size1 increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 298
When the value increases by "1", the aligning amount t mode system/Pa amount adjustment increases by approx.0.8 mm. <Paper length>Long size:330 mm or longer,Middle transport size:220 mm to 329 mm,Short size-1:205 mm to 219 mm,Short size-2:160 mm to 204 mm,Postcard:159 mm or shorter e-STUDIO556/656/756/856...
Page 299
0.25 mm. position/folding position Adjustmen Printer Finisher Fine adjustment of 4150 A3/LD -14-14 When the value increases by "1", the binding/folding t mode binding position shifts toward the right page by 0.25 mm. position/folding position e-STUDIO556/656/756/856...
Page 300
NAD: 18 amount (no paper Others: 20 remained) Adjustmen Printer Paper Adjustment of 4491 3rd drawer Refer to 0-31 <Default value> t mode feeding remained paper contents NAD: 18 amount (no paper Others: 20 remained) e-STUDIO556/656/756/856...
Page 301
Transfer belt motor Fine adjustment of 4528 0-255 t mode rotation speed Adjustmen Printer Drive Fuser roller Fine adjustment of 4529 0-255 t mode rotation speed Adjustmen Printer Drive Fuser roller Fine adjustment of 4530 0-255 t mode rotation speed e-STUDIO556/656/756/856...
Page 302
Adjustmen Printer Drive Fine adjustment of 4538 Normal speed Refer to 0-255 <Default Value> t mode reverse motor rotation contents e-STUDIO556/656: 137 speed e-STUDIO756/856: 135 Adjustmen Printer Drive Fine adjustment of 4538 Increased speed 0-255 t mode reverse motor rotation...
Page 303
Adjustmen Printer Drive Fine adjustment of 4540 Normal speed Refer to 0-255 <Default Value> t mode reverse motor rotation contents e-STUDIO556/656: 137 speed e-STUDIO756/856: 135 Adjustmen Printer Drive Fine adjustment of 4540 Increased speed 0-255 t mode reverse motor rotation...
Page 304
Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (1st drawer) Adjustmen Printer Paper Leading edge position 4562 Thick paper 2 0-40 t mode feeding adjustment correction item on each media type (1st drawer) e-STUDIO556/656/756/856...
Page 305
Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (3rd drawer) Adjustmen Printer Paper Leading edge position 4564 Thick paper 2 0-40 t mode feeding adjustment correction item on each media type (3rd drawer) e-STUDIO556/656/756/856...
Page 306
Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (Tandem LCF) Adjustmen Printer Paper Leading edge position 4566 Thick paper 2 0-40 t mode feeding adjustment correction item on each media type (Tandem LCF) e-STUDIO556/656/756/856...
Page 307
Leading edge position 4568 Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (ADU) Adjustmen Printer Paper Leading edge position 4568 Thick paper 2 0-40 t mode feeding adjustment correction item on each media type (ADU) e-STUDIO556/656/756/856...
Page 308
Plain paper; Short 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment size1 increases by approx.0.8 mm. <Paper length>Short size 1 :205 mm to 219 mm,Short transport size 2 :204 mm or shorter e-STUDIO556/656/756/856...
Page 309
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 310
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 311
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 312
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 313
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 314
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 315
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 316
Thick paper3; Short 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment size1 increases by approx.0.8 mm. <Paper length>Short size 1 :205 mm to 219 mm,Short transport size 2 :204 mm or shorter e-STUDIO556/656/756/856...
Page 317
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 318
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 319
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 320
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 321
<Paper length>Long size :330 mm or longer,Middle transport size :220 mm to 329 mm,Short size 1 :205 mm to 219 mm,Short size 2 :160 mm to 204 mm,Post Card :159 mm or shorter e-STUDIO556/656/756/856...
Page 322
Adjustmen Image Sharpness PPC(black) 7058 Photo 0-255 SYS The larger the value, the sharper the image becomes. t mode Processin adjustmen The smaller the value, the softer the image becomes and the less moire appears. e-STUDIO556/656/756/856...
Page 323
SYS The larger the value, the darker the image becomes. t mode Processin adjustmen adjustment Adjustmen Image Density PPC(black) Automatic density 7125 Photo 0-255 SYS The larger the value, the darker the image becomes. t mode Processin adjustmen adjustment e-STUDIO556/656/756/856...
Page 324
Processin balance surrounding the target area becomes. adjustmen Adjustmen Image Gamma PPC(black) Photo 7192 Medium density 0-255 SYS The larger the value, the darker the image of the area t mode Processin balance surrounding the target area becomes. adjustmen e-STUDIO556/656/756/856...
Page 325
Adjustmen Image Image PPC(black) Text 7213 Beam level 1/4 0-255 The smaller the value, the narrower the beam width t mode Processin contrast becomes and the smaller the dots are reproduced. adjustmen e-STUDIO556/656/756/856...
Page 326
Adjustmen Image Image PPC(black) Presentation 7215 Beam level 2/4 0-255 The smaller the value, the narrower the beam width t mode Processin contrast becomes and the smaller the dots are reproduced. adjustmen e-STUDIO556/656/756/856...
Page 327
Adjustmen Image Gamma PPC(black) User custom 7276 Medium density 0-255 SYS The larger the value, the darker the image of the area t mode Processin balance surrounding the target area becomes. adjustmen e-STUDIO556/656/756/856...
Page 328
SYS 0: Background peak - Fixed t mode Processin correction adjustment 1: Background peak - Varied adjustmen Adjustmen Image Gamma PRT(black) PS/Smooth/600dpi 7315 Low density 0-255 SYS When the value increases, the density in the target t mode Processin balance area becomes higher. adjustmen e-STUDIO556/656/756/856...
Page 329
SYS When the value increases, the density in the target t mode Processin balance area becomes higher. adjustmen Adjustmen Image Gamma PRT(black) PCL/Detail/600dpi 7318 High density 0-255 SYS When the value increases, the density in the target t mode Processin balance area becomes higher. adjustmen e-STUDIO556/656/756/856...
Page 330
Adjustmen Image Image Black NW printer Toner saving ON 7331 0-255 The smaller the value, the narrower the beam width t mode Processin contrast becomes and the smaller the dots are reproduced. adjustmen e-STUDIO556/656/756/856...
Page 331
Adjustmen Image Gamma Monochrome/600dpi/ PS/image 7362 Medium density 0-255 SYS Larger the value, the density for the target area t mode Processin balance Auto increases, and smaller the value, the density for the adjustmen target area decreases. e-STUDIO556/656/756/856...
Page 332
Auto increases, and smaller the value, the density for the adjustmen target area decreases. Adjustmen Image Range SCN(black) Black/Automatic 7416 Text/Photo SYS 0: Background peak - Fixed t mode Processin correction density adjustment 1: Background peak - Varied adjustmen e-STUDIO556/656/756/856...
Page 333
Adjustmen Image Sharpness SCN(black) 7431 Text 0-255 SYS The larger the value, the sharper the image becomes. t mode Processin adjustmen The smaller the value, the softer the image becomes and the less moire appears. e-STUDIO556/656/756/856...
Page 334
Processin adjustmen adjustment value becomes. Adjustmen Image Gamma SCN(black) User custom 7480 Low density 0-255 SYS The larger the value, the darker the image of the area t mode Processin balance surrounding the target area becomes. adjustmen e-STUDIO556/656/756/856...
Page 335
Adjustmen Image Gamma SCN(black) Gray scale 7488 High density 0-255 SYS The larger the value, the darker the image of the area t mode Processin balance surrounding the target area becomes. adjustmen e-STUDIO556/656/756/856...
Page 336
Adjustmen Image Blank 7618 PPC/SCN 0-255 SYS The larger the value, the more the original tends to be t mode Processin page judged as a blank page. judgment threshold adjustmen e-STUDIO556/656/756/856...
Page 337
SYS The smaller the value, the lighter the background t mode Processin d fine becomes. adjustmen Adjustmen Image Backgroun SCN(color) 8310 Text 0-255 SYS The smaller the value, the lighter the background t mode Processin d fine becomes. adjustmen e-STUDIO556/656/756/856...
Page 338
The smaller the value, the duller the image becomes. Adjustmen Image Saturation SCN(color) 8325 Text 0-255 SYS The larger the value, the brighter the image becomes. t mode Processin adjustmen The smaller the value, the duller the image becomes. e-STUDIO556/656/756/856...
Page 339
Printed image 0-255 SYS Sets the changing amount per step of the density t mode Processin adjustmen adjustment/Light step adjustment buttons on the control panel. value The larger the value, the lighter the image of the “light” step becomes. e-STUDIO556/656/756/856...
Page 340
SYS 0: Background peak - Fixed t mode Processin correction density adjustment 1: Background peak - Varied adjustmen Adjustmen Image Backgroun SCN(color) 8370 User custom 0-255 SYS When the value increases, the background becomes t mode Processin lighter. adjustmen e-STUDIO556/656/756/856...
Page 341
Printed image 0-255 SYS The larger the value, the less easily the background t mode Processin d offset adjustment (low density area) is printed. adjustmen The smaller the value, the more easily the background (low density area) is printed. e-STUDIO556/656/756/856...
Page 342
User custom 0-255 SYS The larger the value, the less easily the background t mode Processin d offset adjustment (low density area) is printed. adjustmen The smaller the value, the more easily the background (low density area) is printed. e-STUDIO556/656/756/856...
Page 343
SLIM PDF background processing Adjustmen System General 9960 Equipment Refer to SYS Displays the equipment information in SRAM. t mode information (SRAM) contents 0: Not set 1: Destinations other than NAD 2: NAD <Default value> NAD: 2 Others: 1 e-STUDIO556/656/756/856...
Page 347
Process Fuser 2084 Low-speed pre- Refer to 0: Performs prerunning 1: No pre-running Mode running setting at contents <Default value> recovery from Energy e-STUDIO556/656: Saving Mode JPC: 1 Others: 0 e-STUDIO756/856: 0 Setting Process Fuser Pre-running period Pressure roller 2105...
Page 348
80°C 7: 85°C 8: 90°C 9: 95°C 10: 100°C 11: 105°C temperature during 2130 is enabled) 12: 110°C 13: 115°C 14: 120°C 15: 125°C 16: 130°C ready status <Default value> e-STUDIO556/656: JPC: 6 Others: 10 e-STUDIO756/856: 10 Setting Process Fuser...
Page 349
0: Disabled 1-255: 1-255 sec. Mode period Setting Process Image quality 2842 Developer unit 0~99 Unit: Second Mode control prerunning period before image quality closed-loop control Setting Process Image quality 2844 Image quality closed- 0: Enabled 1: Disabled Mode control loop control(Contrast voltage) e-STUDIO556/656/756/856...
Page 350
4 (Unit: hours) Setting Process Image quality 2891 Maximum number of 0~10 The maximum number of correction which the image Mode control times of image quality quality closed-loop control (contrast voltage) can be closed-loop control performed is set. correction (Contrast voltage) e-STUDIO556/656/756/856...
Page 351
0~1500 The upper limit of the laser power control is set. Mode control (laser power) upper contents [Unit: μW] limiter setting <Default value> e-STUDIO556/656: 1020 e-STUDIO756/856: 610 Setting Process Image quality 2904 Exposure amount Refer to 0~1500 The lower limit of the laser power control is set.
Page 352
0~255 The output value of the transfer bias at the center of the Mode transformer DC contents paper is corrected. correction (C) <Default value> e-STUDIO556/656: 105 e-STUDIO756/856: 139 Setting Process Transfer 2928 Transfer transformer 0~255 The output value of the transfer bias at the trailing edge...
Page 353
The timing to turn on the transfer bias is corrected. Mode correction <e-STUDIO556/656> 0: Approx. 8.2 mm passed from the reference position 1: Approx. 6.8 mm passed from the reference position 2: Approx. 5.4 mm passed from the reference position 3: Approx.
Page 355
LT series - Judges whether it is LT-R or LG by transporting without scanning in reverse to detect its length. APS: The same as that of APS in 0: Disabled . e-STUDIO556/656/756/856...
Page 356
SYS To access the data in the noncontact IC card, the Key Mode 429496729 Information "LLLL" and the Sector Number "MMMM" should be set. The "LLLL" should be set first, and then "MMMM". <KP-2005> LLLL: Key information MMMM: Sector number (hexadecimal number) e-STUDIO556/656/756/856...
Page 357
Setting System General 3624 Log item filtering 214748 0~4294967 SYS Changes target log items for notification in real time log Mode setting for real time 3921 notification function. log notification function. e-STUDIO556/656/756/856...
Page 358
Enable/Disable SYS 0: Disabled Mode setting of standard 1: Enabled EWB function * This code is valid for the following model or destination: - e-STUDIO556SE/656SE/756SE/856SE - e-STUDIO556/656/756/856 for MJD Setting System Network 3631 Remote Access SYS 0: Disabled Mode (SNMP)
Page 359
9083 to set the default value. Setting System Network 3722 Device authentication 1~180 NIC Applied to the device authentication Mode PDC/BDC time-out period (Unit: Seconds) Setting System Network 3723 User authentication 1~180 NIC Applied to the user authentication Mode PDC/BDC time-out period (Unit: Seconds) e-STUDIO556/656/756/856...
Page 360
System Network 3731 Raw TCP max 1~16 Mode connection Setting System Network 3732 Raw TCP active 1~16 Mode connection Setting System Network 3736 DNS Client Time Out 1~180 NIC Use when a timeout occurred at DNS client connection Mode e-STUDIO556/656/756/856...
Page 361
IPv6 3772 Default Gateway Sets the default gateway for IPv6 address. Maximum 40 Mode setting characters (byte). Setting System Network 3774 DHCPv6 Option NIC DHCPv6 Option is switched when the Manual is set. Mode setting 1: Enabled 2: Disabled e-STUDIO556/656/756/856...
Page 362
SYS Department Management is set when Remote Scan is Mode Management setting performed. by Remote Scan 0: w/o GUI OFF,w/ GUI OFF 1: w/o GUI ON,w/ GUI OFF 2: w/o GUI OFF,w/ GUI ON 3: w/o GUI ON,w/ GUI ON e-STUDIO556/656/756/856...
Page 363
0: Disabled 1: Enabled Setting System General 3837 Display switching for SYS The display method of the machine name/computer Mode the machine name shown in the event-related notification is name/computer name switched. shown in the 0: IP address 1: NetBIOS name/FQDN notification e-STUDIO556/656/756/856...
Page 364
Others: 0 Setting System General 3853 Summer time mode SYS Summer time is started as follows when 08-3852 is Mode Offset value enabled. 0: +2:00 1: +1:30 2: +1:00 3: +0:30 4: -0:30 5: -1:00 6: -1:30 7: -2:00 e-STUDIO556/656/756/856...
Page 365
SYS The month in which summer time is ended is set. Mode Ending month contents 1: January 2: February 3: March 4: April 5: May 6: June 7: July 8: August 9: September 10: October 11: November 12: December <Default value> NAD: 11 MJD: 10 Others: 1 e-STUDIO556/656/756/856...
Page 367
0: Does not change the paper source automatically 1: Changes the paper source automatically e-STUDIO556/656/756/856...
Page 368
Sets the number of times of the feeding retry from the Mode setting Tandem LCF. Setting Printer Paper feeding Feeding retry number T-LCF 4025 Others Sets the number of times of the feeding retry from the Mode setting Tandem LCF. e-STUDIO556/656/756/856...
Page 369
Paper size for 3rd Refer to 0~255 Press the button on the LCD to select the size. Mode drawer contents This code is reset every time a paper size is detected automatically. 20: A4-R 80: LT-R <Default value> NAD: 80 Others: 20 e-STUDIO556/656/756/856...
Page 370
Paper feeding 4108 Paper size (A5-R) 210/148 182~432/1 Mode feeding/widthwise 40~297 direction Setting Printer Paper feeding 4109 Paper size (B4) 364/257 182~432/1 Mode feeding/widthwise 40~297 direction Setting Printer Paper feeding 4110 Paper size (B5-R) 257/182 182~432/1 Mode feeding/widthwise 40~297 direction e-STUDIO556/656/756/856...
Page 371
4118 Paper size (8.5"X8.5") 216/216 182~432/1 Mode feeding/widthwise 40~297 direction Setting Printer Paper feeding 4119 Paper size (Non- 432/279 148~432/1 Mode standard) 05~297 feeding/widthwise direction Setting Printer Paper feeding 4120 Paper size (8K) 390/270 182~432/1 Mode feeding/widthwise 40~297 direction e-STUDIO556/656/756/856...
Page 372
Refer to Press the button on the LCD to select the size. Mode contents 4: A4 64: LT <Default value> NAD: 64 Others: 4 Setting Printer Paper feeding 4526 Reversing speed 0: Accelerated 1: Low speed Mode switching for thick paper e-STUDIO556/656/756/856...
Page 373
* Set this code to "0" when replacing the Toner bag. Setting Printer Paper feeding 4542 Incorrect paper size 0: Enabled 1: Disabled Mode jam detection switching Setting Printer Paper feeding 4543 Paper feeding timing 0-3: Setting value X 10msec Mode correction setting e-STUDIO556/656/756/856...
Page 374
Setting Printer General 4586 Checking of NVRAM Refer to 190-193 <Default value> Mode board data on LGC content 190: e-STUDIO556 board No. 1 (Models) 191: e-STUDIO656 192: e-STUDIO756 193: e-STUDIO856 Setting Printer Feeding 4602 Paper transport 0: Enabled 1: Disabled...
Page 375
4: Toner near-empty status threshold value: (%)* 5: Toner near-empty status threshold value: (Number of sheets)* * The toner near-empty status is displayed if the remaining amount of toner is equal to or less than the amount set in 08-5810/5811 (percentage or number of sheets). e-STUDIO556/656/756/856...
Page 376
Others: 600,000 Setting Counter Maintenance 5555 Setting value of PM Refer to 8 digits <Default value> Mode time counter display/0 content e-STUDIO556/656: 400,000 clearing e-STUDIO756/856: 330,000 Setting Counter Maintenance 5562 Setting value of PM Refer to 8 digits <Default value> Mode...
Page 377
Setting value of PM Refer to 8 digits Time accumulating counter Mode time counter display/0 content <Default value> clearing / Parts e-STUDIO556/656 :470,000 e-STUDIO756/856 :390,000 Setting Counter Maintenance 5568 Current value of PM 8 digits Counts up when the registration sensor is ON.
Page 378
SYS Counts the number of output pages in the Copier Mode output pages in copier Function function according to its size(large/small). Large:Number of output pages of large-sized paper defined at 08-6011 Small:Number of output pages other than set as large- sized paper e-STUDIO556/656/756/856...
Page 379
SYS Counts the number of output pages in the FAX Function Mode output pages in FAX according to its size (large/small). function Large:Number of output pages of large-sized paper defined at 08-6011 Small:Number of output pages other than set as large- sized paper e-STUDIO556/656/756/856...
Page 380
SYS Counts the number of scanning pages in the Copier Mode scanning pages in Function copier function according to its size(large/small). Large:Number of output pages of large-sized paper defined at 08-6011 Small:Number of output pages other than set as large- sized paper e-STUDIO556/656/756/856...
Page 381
SYS Counts the number of transmitted pages in the FAX Mode transmitted pages in Function according to its size (large/small). FAX function Large:Number of output pages of large-sized paper defined at 08-6011 Small:Number of output pages other than set as large- sized paper e-STUDIO556/656/756/856...
Page 382
0 (weight: 0.00) – 9999 (weight: 99.99) Setting Counter Custom For administrator Weighting/Scanning 6081 Full Color 0-9999 SYS Weights subtraction of scanning from department/user Mode counter/Job Job Quota and addition of Scan Counter to Custom Quota Counter. 0 (weight: 0.00) – 9999 (weight: 99.99) e-STUDIO556/656/756/856...
Page 383
Envelop Refer to SYS Sets the weight of fee charging count for printing per Mode setting for contents page. Scan counter and fax counter are not influenced. paper type 0: Single 1: Double <Default value> JPC/CND: 0 Others: 1 e-STUDIO556/656/756/856...
Page 384
0 (weight: 0.00) – 9999 (weight: 99.99) Setting Counter Custom For administrator Weighting/Print 6085 Black/Large 0-9999 SYS Weights subtraction of printing from department/user Mode counter/Job Job Quota and addition of printing to Custom Counter. Quota 0 (weight: 0.00) – 9999 (weight: 99.99) e-STUDIO556/656/756/856...
Page 385
SYS Weights addition of print to Custom Counter (Total Mode counter Counter). Since the count is calculated based on the existing Large/Small counter, the count before changing this setting is also included in the count. 0 (weight: 0.00) – 9999 (weight: 99.99) e-STUDIO556/656/756/856...
Page 386
Setting Counter Counter of 6116 8 digits Counts the number of output pages of duplex printing. Mode Paper feed Setting Counter Counter of 6117 RADF 8 digits SYS Counts the number of originals fed from RADF. Mode Paper feed e-STUDIO556/656/756/856...
Page 387
Setting value Refer to 8 digits Sets the threshold for displaying a message for PM Mode contents timing. 0: Not displayed <Default value> e-STUDIO556/656: 495,000 e-STUDIO756/856: 410,000 [Unit: count] Setting Counter Maintenance PM counter 6194 Current value 8 digits Counts up when the registration sensor is ON.
Page 388
Setting Process Fuser 6199 Setting value to Refer to 8 digits <Default value> Mode display that the contents e-STUDIO556: 410,000 cleaning web is e-STUDIO656: 465,000 almost consumed e-STUDIO756: 490,000 e-STUDIO856: 550,000 (Setting value x1 sheet) Setting Process Fuser 6200 Setting value to...
Page 389
When the number of feeding retry (08-6230 to 08-6235) Mode upper limit exceeds the setting value, the feeding retry will not be value(Bypass feed) performed subsequently. In case "0" is set as a setting value, however, the feeding retry continues regardless of the counter setting value. e-STUDIO556/656/756/856...
Page 390
The toner is also consumed wastefully when the paper misfeeding occurs. Replace the roller at earlier timing if the paper misfeedings have occurred frequently. Setting Counter PM counter Photoconductive 6250 Present number of 8 digits mode drum output pages e-STUDIO556/656/756/856...
Page 391
Counter PM counter Photoconductive 6250 Recommended Refer to 8 digits <Default value> mode drum number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Photoconductive 6250 Number of output 8 digits...
Page 392
Counter PM counter Drum cleaning blade 6258 Recommended Refer to 8 digits <Default value> mode driving counts to be contents e-STUDIO556/656: 495,000 replaced e-STUDIO756/856: 410,000 Setting Counter PM counter Drum cleaning blade 6258 Driving counts at the 8 digits mode...
Page 393
Counter PM counter Drum separation 6272 Recommended Refer to 8 digits <Default value> mode finger number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Drum separation 6272 Number of output...
Page 394
Counter PM counter Main charger grid 6274 Recommended Refer to 8 digits <Default value> mode number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Main charger grid 6274 Number of output...
Page 395
Counter PM counter Main charger wire 6282 Recommended Refer to 8 digits <Default value> mode driving counts to be contents e-STUDIO556/656: 495,000 replaced e-STUDIO756/856: 410,000 Setting Counter PM counter Main charger wire 6282 Driving counts at the 8 digits mode...
Page 396
Setting Counter PM counter Ozone filter 6298 Recommended Refer to 8 digits <Default value> mode number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Ozone filter 6298 Number of output...
Page 397
Setting Counter PM counter Developer material 6300 Recommended Refer to 8 digits <Default value> mode number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Developer material 6300 Number of output...
Page 398
Counter PM counter Toner filter 6308 Recommended Refer to 8 digits <Default value> mode driving counts to be contents e-STUDIO556/656: 400,000 replaced e-STUDIO756/856: 330,000 Setting Counter PM counter Toner filter 6308 Driving counts at the 8 digits mode last replacement...
Page 399
Setting Counter PM counter Transfer belt 6328 Recommended Refer to 8 digits <Default value> mode number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Transfer belt 6328 Number of output...
Page 400
PM counter Transfer belt cleaning 6332 Recommended Refer to 8 digits <Default value> mode blade driving counts to be contents e-STUDIO556/656: 495,000 replaced e-STUDIO756/856: 410,000 Setting Counter PM counter Transfer belt cleaning 6332 Driving counts at the 8 digits mode...
Page 401
Setting Counter PM counter Fuser roller 6346 Recommended Refer to 8 digits <Default value> mode number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Fuser roller 6346 Number of output...
Page 402
Counter PM counter Pressure roller 6350 Recommended Refer to 8 digits <Default value> mode driving counts to be contents e-STUDIO556/656: 940,000 replaced e-STUDIO756/856: 780,000 Setting Counter PM counter Pressure roller 6350 Driving counts at the 8 digits mode last replacement...
Page 403
Counter PM counter Cleaning web roller 6354 Recommended Refer to 8 digits <Default value> mode number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Cleaning web roller 6354 Number of output...
Page 404
PM counter Fuser roller 6368 Recommended Refer to 8 digits <Default value> mode separation finger number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Fuser roller 6368 Number of output...
Page 405
LCF) pages at the last replacement Setting Counter PM counter Pickup roller (Tandem 6388 Number of times 8 digits mode LCF) replaced Setting Counter PM counter Pickup roller (Tandem 6389 Date of previous 8 digits mode LCF) replacement e-STUDIO556/656/756/856...
Page 406
LCF) pages at the last replacement Setting Counter PM counter Pickup roller (Option 6394 Number of times 8 digits mode LCF) replaced Setting Counter PM counter Pickup roller (Option 6395 Date of previous 8 digits mode LCF) replacement e-STUDIO556/656/756/856...
Page 407
Setting Counter PM counter Feed roller (2nd 6400 Number of times 8 digits mode drawer) replaced Setting Counter PM counter Feed roller (2nd 6401 Date of previous 8 digits mode drawer) replacement e-STUDIO556/656/756/856...
Page 408
Setting Counter PM counter Separation roller (1st 6406 Number of times 8 digits mode drawer) replaced Setting Counter PM counter Separation roller (1st 6407 Date of previous 8 digits mode drawer) replacement e-STUDIO556/656/756/856...
Page 409
Setting Counter PM counter Separation roller (3rd 6412 Number of times 8 digits mode drawer) replaced Setting Counter PM counter Separation roller (3rd 6413 Date of previous 8 digits mode drawer) replacement e-STUDIO556/656/756/856...
Page 410
Setting Counter PM counter Feed roller (3rd 6420 Number of times 8 digits mode drawer) replaced Setting Counter PM counter Feed roller (3rd 6421 Date of previous 8 digits mode drawer) replacement e-STUDIO556/656/756/856...
Page 411
Setting Counter PM counter Pickup roller (3rd 6428 Number of times 8 digits mode drawer) replaced Setting Counter PM counter Pickup roller (3rd 6429 Date of previous 8 digits mode drawer) replacement e-STUDIO556/656/756/856...
Page 412
PM counter Web roller one-way 6438 Recommended Refer to 8 digits <Default value> mode clutch number of output contents e-STUDIO556: 460,000 pages for e-STUDIO656: 515,000 replacement e-STUDIO756: 540,000 e-STUDIO856: 600,000 Setting Counter PM counter Web roller one-way 6438 Number of output...
Page 413
PM counter Web roller one-way 6438 Recommended Refer to 8 digits <Default value> mode clutch driving counts to be contents e-STUDIO556/656: 470,000 replaced e-STUDIO756/856: 390,000 Setting Counter PM counter Web roller one-way 6438 Driving counts at the 8 digits mode...
Page 414
Setting Counter Pixel counter Number of output 6561 8 digits SYS Counts the number of output pages converted to the Mode pages(Service standard paper size in the FAX function and service technician reference) technician reference.[Unit. page] e-STUDIO556/656/756/856...
Page 415
SYS Displays the latest pixel count in the printer function and Mode count(Service service technician reference.[Unit: 0.01%] technician reference) Setting Counter Pixel counter Latest pixel 6618 0~10000 SYS Displays the latest pixel count in the FAX function and Mode count(Service service technician reference.[Unit: 0.01%] technician reference) e-STUDIO556/656/756/856...
Page 416
6721 20.1-25% 8 digits SYS The pixel count data are divided into 10 ranges. The Mode distribution number of output pages in each range is displayed. In this code, the distributions in the copy function are displayed. [Unit: page] e-STUDIO556/656/756/856...
Page 417
6722 25.1-30% 8 digits SYS The pixel count data are divided into 10 ranges. The Mode distribution number of output pages in each range is displayed. In this code, the distributions in the printer function are displayed. [Unit: page] e-STUDIO556/656/756/856...
Page 418
Pixel counter Pixel count 6723 30.1-40% 8 digits SYS The pixel count data are divided into 10 ranges. The Mode distribution number of output pages in each range is displayed. In this code, the distributions in the FAX function are displayed.[Unit: page] e-STUDIO556/656/756/856...
Page 419
Setting Image Automatic Last updated date 7051 Monochrome PPC SYS Last updated date and time of automatic tone correction Mode Processing tone and time 421231235 data. correction YYMMDDHHMM data YY: year, MM: month, DD: day, HH: hour, MM: minute e-STUDIO556/656/756/856...
Page 420
Setting System General 8511 Wide A4 Mode (for SYS 0: Disable 1: Enable Mode PCL) Setting System General 8512 Number of jobs in 2~10 SYS 2-10: From 2 to jobs can be specified Mode batch processing e-STUDIO556/656/756/856...
Page 421
1: \ / > < " | ? * : * 0: Existing model standard 1: Windows standard Since setting the value to "1" allows some prohibited characters, filename might not be processed in external application or server. e-STUDIO556/656/756/856...
Page 422
SYS Sets whether minus value can be input or not for image Mode value for image shift shift when copying. If this setting is enabled, the minus when copying value can be input only for back side. 0: Inputting minus value is disabled. 1: Inputting minus value is enabled. e-STUDIO556/656/756/856...
Page 424
Switchover of display SYS Switches the display method of filename. Mode method of filename 0: Displays the filename from the beginning 1: Displays the trailing characters 2: Displays the beginning and trailing characters 3: Displays the filename without abbreviation e-STUDIO556/656/756/856...
Page 425
LDAP authentication 8646 LDAP attribute name eBMUse SYS Maximum 32 characters (ASCII). Mode settings 6 rCard Setting System User interface Card reading device LDAP authentication 8647 LDAP attribute name eBMUse SYS Maximum 32 characters (ASCII). Mode settings 7 rCard e-STUDIO556/656/756/856...
Page 426
Setting System User interface Sound 8663 Fax transmission SYS 0: OFF 1: ON Mode error Setting System User interface Sound Hours for mute 8664 Enable/Disable SYS 0: Mute is disabled 1: Mute is enabled Mode setting of mute e-STUDIO556/656/756/856...
Page 427
Setting System 8700 Secret reception SYS When the value of 08-8924 is "0", the value of this code Mode setting can be set to "1" or "2". 0: Always Off 1: Always On 2. Scheduled reception e-STUDIO556/656/756/856...
Page 428
User interface Service notification 8715 Password for zip file #10481 SYS Password for zip file with password of service Mode information with password notification information. Minimum number of digits: 0, maximum number of digits: 20 Available character: alphanumeric characters and symbols e-STUDIO556/656/756/856...
Page 429
Home Directory cannot be obtained depending on the user. 0: Displays the pop-up dialog when user logs in 1: Displays the message in the guidance area when the Scan to File screen is displayed e-STUDIO556/656/756/856...
Page 430
SYS Normally this setting is made in TopAccess. Mode printing of driver setting 0: Disabled 1: Enabled user name Setting System Forced 8728 Application to network SYS Normally this setting is made in TopAccess. Mode printing of fax job 0: Disabled 1: Enabled user name e-STUDIO556/656/756/856...
Page 431
Setting System User interface 8731 Gradation icon setting SYS Switches the gradation of icon. Mode 0: Uses normal icon 1: Uses gradation icon Setting System Scanning 8735 Sending setting of SYS 0: Disabled 1: Enabled Mode ScanToURL e-STUDIO556/656/756/856...
Page 432
Setting System Maintenance Notification of 8756 Remaining amount at 0-100 SYS 0 to 100% Mode remaining amount of first notification toner Setting System Maintenance Notification of 8756 Notification interval 1-25 SYS 1 to 25% Mode remaining amount of toner e-STUDIO556/656/756/856...
Page 433
Attribute value setting eBMUse SYS Attribute name of PIN code mode of LDAP PIN rPIN authentication server Setting System Network PIN code 8778 Attribute value setting eBMUse SYS Attribute name of PIN code mode of LDAP PIN rPIN authentication server e-STUDIO556/656/756/856...
Page 434
SYS Sets whether the pop-up is displayed or not when jobs mode pop-up for automatic are automatically released after user authentication. output of jobs This code is effective when the value of 08-8915 is "1" (Enabled). 0: Pop-up is not displayed 1: Pop-up is displayed e-STUDIO556/656/756/856...
Page 435
NIC 1: Enable CRL 2: Disable CRL Mode Setting System Network 8824 FTP client mode NIC Sets the FTP transfer mode when FTP is selected for mode "FILE" to save the scanned data. 0: Automatic 1: Passive mode 2: Active mode e-STUDIO556/656/756/856...
Page 436
1: ON (printing continued by automatically selecting the paper error available exit tray) Setting System Continuous 8906 Copy SYS 0: OFF (copying not continued) Mode print setting 1: ON (copying continued by canceling punching when setting) punching dust box is full e-STUDIO556/656/756/856...
Page 437
InternetFAX SYS Sets whether the InternetFAX function is enabled or Mode setting disabled. 0: Disabled 1: Enabled Setting System MFP function 8914 Email SYS Sets whether the email function is enabled or disabled. Mode setting 0: Disabled 1: Enabled e-STUDIO556/656/756/856...
Page 438
SMB server is enabled or disabled. 0: Disabled 1: Enabled Setting System MFP function 8914 Save as Netware SYS Sets whether the function that saves scanned data of Mode setting originals to the Netware server is enabled or disabled. 0: Disabled 1: Enabled e-STUDIO556/656/756/856...
Page 439
SYS Selects the bin/tray to which the paper is output. Mode FAX/InternetFAX/e- 0: Finisher 1st bin mail printing 1: Finisher 1st bin 2: Finisher 2nd bin Setting System Department 8921 Clearing of the SYS 0: Not allowed Mode management user/department 1: Allowed counter e-STUDIO556/656/756/856...
Page 440
User interface 8932 Availability of Netware NIC 1: Enabled Mode 2: Disabled Setting System User interface 8933 SSL setting (SSL NIC 1: Enabled (accepts all server certificates) Mode SMTP Client Off/on) 2: Disabled 3: Enabled (uses the imported CA certificate) e-STUDIO556/656/756/856...
Page 441
However, this code does not work depending on the conditions, such as when stapling is selected. Set this code when requested by user or the guides width sensor is broken. Related code: 08-4621. 0: Invalid 1: Valid e-STUDIO556/656/756/856...
Page 442
NIC Sets whether the remote scanning is enabled or Mode Scan while control disabled if the user is logged in using the control panel panel is operated when user authentication or department management is enabled. 0: Disabled 1: Enabled e-STUDIO556/656/756/856...
Page 443
User interface NFC reader 8986 Usage type SYS 0011ZZZZ (First 4 digits are fixed) Mode 429496729 -ZZZZ: Sub code 0000: No authentication using card 0001: IDm (FeliCa/NFC-FeliCa) and (or) UID (Mifare/NFC-Mifare) are used 0002: Data (FeliCa/NFC-FeliCa/Mifare/NFC-Mifare) 0003: SSFC mode e-STUDIO556/656/756/856...
Page 444
SYS 1st to 31th. Input "0" to disable this setting. Mode equipment information Setting System Maintenance Notification of Notification day 2 8993 Notification day 2 0-31 SYS 1st to 31th. Input "0" to disable this setting. Mode equipment information e-STUDIO556/656/756/856...
Page 445
System Maintenance Notification of Pixel counter list 8999 Service engineer SYS 0: Disabled Mode equipment information reference 1: Enabled Setting System Maintenance Notification of Error history list 8999 Maximum 1000 items SYS 0: Disabled Mode equipment information 1: Enabled e-STUDIO556/656/756/856...
Page 446
0: For factory shipment 1: For line Field: "0" must be Mode selected Setting System User interface 9012 Language displayed Refer to SYS <Default value> Mode at power-ON contents JPC: Japanese TWD: Traditional Chinese CND: Simplified Chinese KRD: Korean Others: English e-STUDIO556/656/756/856...
Page 447
1 to 255: n days before Setting System General 9026 Notifying address of SYS Sets where the end of the trial period is to be notified. 0: Mode trial period end OFF 1: User 2: Service center 3: User and service center e-STUDIO556/656/756/856...
Page 448
“Enter Department Code” is displayed on the control panel even if the department management function is not set on. In this case, initialize the area with this code. This area is normally initialized at the factory. e-STUDIO556/656/756/856...
Page 449
SYS Timer to return the equipment to the default settings Mode setting when the [START] button is not pressed after the function and the mode are set. 0: No limit (disabled) 1 to 10: Set number x 15 sec. e-STUDIO556/656/756/856...
Page 450
0: Invalid 4: 1 min. 6: 3 min. 7: 4 min. 8: 5 min. 9: 7 min. 10: 10 min. 11: 15 min. 12: 20 min. 13: 30 min. 14: 45 min. 15: 60 min. <Default value> e-STUDIO556: 6 e-STUDIO656/756/856: 8 Setting System...
Page 451
1: AMS (Automatic Magnification Selection) 2: Not selected Setting System User interface Default setting of 9134 Default setting SYS 0: Continuous feeding (by pressing the [START] button) Mode RADF mode 1: Single feeding (by setting original on the tray) e-STUDIO556/656/756/856...
Page 452
SYS 0: ON 1: OFF Mode image shift copying (linkage of front side and back side) Setting System User interface 9150 Automatic Sorting SYS 0: Invalid 1: STAPLE 2: SORT 3: GROUP 4: ROTATE Mode Mode setting (RADF) SORT e-STUDIO556/656/756/856...
Page 453
1: Enabled Setting System User interface Cascade operation PPC / FAX 9158 Operation setting SYS 0: Once mode setting 1: Circulation (Loop) Setting System User interface Cascade operation Printer/Box 9159 Enable/Disable SYS 0: Disabled mode setting setting 1: Enabled e-STUDIO556/656/756/856...
Page 454
System 9183 Application of paper SYS 0: Not subjected for APS judgment 1: Subjected for Mode source priority APS judgment selection Setting System User interface 9184 Centering printing of SYS 0: Invalid 1: Valid Mode primary/secondary direction at AMS e-STUDIO556/656/756/856...
Page 455
HDD is full 0: Not full retained 1: Fully retained - Retains the source file until CutDoc/SaveDoc command is completed. The file is not deleted even if the HDD has become full during the execution of command when "1" is set. e-STUDIO556/656/756/856...
Page 456
(center) 6: Step +1 7: Step +2 8: Step +3 9: Step +4 adjustment (Full Color) Setting System User interface Default mode setting Default setting (SCN) 9215 Color mode SYS 0: Black Mode 1: Gray Scale 2: Unused 3: Full Color 4: Auto Color e-STUDIO556/656/756/856...
Page 457
19: Size mixed 20: 8K 21: 16K 22: 16K-R Setting System General 9225 Searching interval of 1~24 SYS Sets the search interval of deleting expired files and Mode deleting expired files checking capacity of HDD partitions.(Unit: Hour)Related and checking capacity code 08-9208 of HDD partitions e-STUDIO556/656/756/856...
Page 458
0-255 SYS Sets the binarizing level of each step. When the value Mode setting (When judging increases, the image becomes darker. When the value as black in the ACS decreases, the image becomes lighter. Refer to 08- Mode) 9204. e-STUDIO556/656/756/856...
Page 459
OFF to ON, the value in this code changes from "1" to "2", and "3" to "4". The value does not change if it is "2" or"4". Reset this value as necessary when changing user data department management (08-9264) from OFF to ON. e-STUDIO556/656/756/856...
Page 460
When the value of this code is set to "1", the scanning performance increases at fax transmission. However, the whole image cannot be output since FOLIO is judged as A4-R. 0: Judgment is enabled 1: Judgment is disabled e-STUDIO556/656/756/856...
Page 461
SYS 0: Not permitted 1: Permitted Mode address edit at "Scan to Email" Setting System Network 9278 E-mail domain name SYS 96+2 (delimiter) character ASCII sequence only Mode Setting System User interface Sound 9280 Error sound SYS 0: OFF 1: ON Mode e-STUDIO556/656/756/856...
Page 462
2: Can be set only from the Address book 3: Can be set only from the LDAP server Setting System Paper feeding 9300 1st drawer Paper SYS 0: Plain paper Mode information 1: Thick paper 1 2: Thick paper 2 3: Thick paper 3 e-STUDIO556/656/756/856...
Page 463
31: 1 hour 32: 2 hours 33: 4 hours 34: 8 hours 35: 12 hours 50: 5 min. 51: 10 min. 52: 15 min. 53: 30 min. Setting System Network 9308 Raw printing job SYS 0: Valid 1: Invalid Mode (Duplex) e-STUDIO556/656/756/856...
Page 464
Setting System Network 9316 Raw printing job(PCL 1200 400~99975 SYS Sets the font size from 4 to 999.75. (A hundredfold of Mode font size) the font size is defined as the setting value.) e-STUDIO556/656/756/856...
Page 465
When both are set, each content is displayed alternately. 0: Not displayed 1: Displayed Setting System General 9328 Banner advertising SYS Maximum 27 letters (one-byte character) Mode display 1 e-STUDIO556/656/756/856...
Page 466
0: No restriction 1: Permitted only under administrator's privilege Setting System Network 9338 Raw printing SYS 0: AUTO 1: 1st drawer 2: 2nd drawer 3: 3rd drawer 4: Mode job(Paper feeding 4th drawer 5: Tandem LCF 6: External LCF drawer) e-STUDIO556/656/756/856...
Page 467
User interface 9342 Margin width 0~30 Mode (Bookbinding margin) Setting Printer Paper feeding Automatic change of Auto 9343 Printing/BOX printing SYS 1: Only in the same paper direction Mode paper source 2: In both the same and different paper directions e-STUDIO556/656/756/856...
Page 468
1: Encryption valid (Security priority) Encrypts all of the (Except for CND) user's data. 2: Encryption valid (Performance priority) Encrypts the user's data except the files temporarily created and deleted in the image processing such as copying or printing. e-STUDIO556/656/756/856...
Page 469
Email transmission. as file" and Email 0: [YYYY][MM][DD][HH][mm][SS] transmission 1: [YY][MM][DD][HH][mm][SS] 2: [YYYY][MM][DD] 3: [YY][MM][DD] 4: [HH][mm][SS] 5: [YYYY][MM][DD][HH][mm][SS][mm0] The order of [YY], [MM] and [DD] varies depending on the setting of the code 08-9102 (Data display format). e-STUDIO556/656/756/856...
Page 470
Address 9408 IP address Refer to Refer to NIC <Default value> Mode contents contents 0.0.0.0 <Acceptable value> 0.0.0.0-255.255.255.255 Setting System Network Address 9409 Subnet mask Refer to Refer to NIC <Default value> Mode contents contents 0.0.0.0 <Acceptable value> 0.0.0.0-255.255.255.255 e-STUDIO556/656/756/856...
Page 471
9446 Availability of POP3 NIC 1: Available 2: Not available Mode clients Setting System Network 9459 Availability of FTP NIC 1: Available 2: Not available Mode server Setting System Network 9463 MIB function NIC 1: Valid 2: Invalid Mode e-STUDIO556/656/756/856...
Page 472
System Network 9517 BDC (Backup Domain UTY Maximum 128 letters Mode Controller) name No.1 of authentication Setting System Network Address 9525 Display of MAC (**:**:**:**:**:**) Mode address The address is displayed as above. 6-byte data is divided by colon. e-STUDIO556/656/756/856...
Page 473
9601 Equipment number 9 digits SYS This code can be also keyed in from the adjustment Mode (serial number) mode (05-9043). 9 digits display Setting System Maintenance 9602 Dealer's name SYS Maximum 100 letters Needed at initial registration Mode e-STUDIO556/656/756/856...
Page 474
Day-4 Setting System Maintenance Remote-controlled Remote-controlled 9614 Sunday SYS 0: Invalid 1: Valid Mode service service polling day Setting System Maintenance Remote-controlled Remote-controlled 9615 Monday SYS 0: Invalid 1: Valid Mode service service polling day e-STUDIO556/656/756/856...
Page 475
Wireless LAN 9649 Wireless LAN NIC This setting is whether the wireless LAN connection is Mode supplicant Wireless enabled or disabled. LAN setting 1: Enabled 2: Disabled Setting System Bluetooth 9680 Bluetooth ON/OFF SYS 0: OFF 1: ON Mode setting e-STUDIO556/656/756/856...
Page 476
URL setting contents <Default value> https://device.mfp- support.com:443/device/firstregist.ashx Setting System Maintenance Short time interval of 9718 Recovery time setting 1~48 SYS Sets the time interval to recover from the Emergency Mode emergency mode Mode to the Normal Mode.(Unit: Hour) e-STUDIO556/656/756/856...
Page 477
SYS Input IP address or FQDN. Mode service address setting contents <Default value> 0.0.0.0 Setting System Maintenance Remote-controlled HTTP 9742 HTTP proxy port 0~65535 Mode service number setting Setting System Maintenance Remote-controlled HTTP 9743 HTTP proxy ID setting SYS Maximum 30 letters Mode service e-STUDIO556/656/756/856...
Page 478
User's E-mail address Setting System Maintenance 9759 Automatic ordering SYS Maximum 100 letters Mode (Remote) function of supplies User's address Setting System Maintenance 9760 Automatic ordering 5 digits SYS Maximum 5 digits Mode (Remote) function of supplies Service number e-STUDIO556/656/756/856...
Page 479
Order quantity of toner cartridge Setting System Maintenance 9778 Information about 1~99 Mode (Remote) supplies Condition number of toner cartridge Setting System Maintenance 9779 Information about SYS Maximum 20 digits Mode (Remote) supplies Part number of used toner bag e-STUDIO556/656/756/856...
Page 480
9794, 9607, 9608) 0: Invalid 1: Valid (E-mail) 2: Valid (FAX) Setting System Maintenance 9794 Destination E-mail SYS Maximum 192 letters Mode (Remote) address Setting System Maintenance 9795 Total counter SYS 0: Invalid 1: Valid Mode (Remote) information transmission setting e-STUDIO556/656/756/856...
Page 481
This code is valid only when printing in the stapling mode. However, printing is always interrupted when staple for saddle stitch runs out. 0: Continues printing by switching to sort setting 1: Interrupts printing e-STUDIO556/656/756/856...
Page 482
SYS 0: DOCYYMMDD 1: NetBios name Mode saving/attachment files of "File/Email" Setting System User interface Off Device 9819 STAGE SSL SYS Sets whether SSL communication is enabled or Mode Customization disabled for remote scanning. Architecture 0: Disabled 1: Enabled e-STUDIO556/656/756/856...
Page 484
SYS Acceptance of the usage of the USB data cloning tool Mode USB cloning 0: Accepted 1: Not accepted Setting System User interface Screen setting 9891 Warning message SYS 0: No warning notification 1: Warning notification Mode when PM time has come e-STUDIO556/656/756/856...
Page 485
0: Disabled 1: Enabled Setting System Finisher Stapling setting 9937 Plain ~100~100 SYS -100 to 100 Mode Acceptable number of sheets exceeding upper limit / Short size e-STUDIO556/656/756/856...
Page 486
Setting System Version Engine 9940 PFC ROM version 320F-XXX If the PFC ROM version is displayed as Mode "NGD" in this code, it denotes that the updating of the PFC ROM failed. In this case, retry the firmware update. e-STUDIO556/656/756/856...
Page 487
1: Destinations other than NAD 2: NAD <Default value> NAD: 2 Others: 1 Setting System User interface 9963 Display of receiving SYS This setting is automatically disabled in the high Mode job on JOB STATUS security mode. screen 0: Disabled 1: Enabled e-STUDIO556/656/756/856...
Page 488
TO/CC/BCC field can be edited by pressing the TO/CC/BCC button. 0: Disabled 1: Fixed to TO field. 2: Added to TO field. 3: Added to CC field. 4: Added to BCC field. Setting System Network 9981 Sending Email text SYS 0: Disabled 1: Enabled Mode e-STUDIO556/656/756/856...
Page 489
1: Clears all 2: Clears only addresses 3: Retains all settings * When the value of this code is set to "3", the value of 08-3847 (FAX mistransmission prevention) is automatically set to "1" (Enabled). e-STUDIO556/656/756/856...
Page 490
Input check (Test mode 03) [FAX] button: OFF / [COPY] button: OFF ([FAX] LED: OFF / [COPY] LED: OFF) Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Intermediate transport sensor No paper Paper present 1st drawer transport sensor No paper Paper present 1st drawer feed sensor...
Page 491
Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Bypass paper size detection sensor-3 Other than A3/LD A3/LD (Refer to Table 1) Bypass paper size detection sensor-2 Other than A4-R/LT- A4-R/LT-R (Refer to Table 1) Bypass paper size detection sensor-1 Other than A5-R/ST- A5-R/ST-R (Refer to Table 1)
Page 492
Table 1. Relation between the status of the bypass paper size detection sensor and the paper width Bypass paper-width sensor Paper-width size A3/LD A4-R/LT-R A5-R/ST-R Card size B4/LG B5-R e-STUIDIO557/657/757/857...
Page 493
[FAX] button: ON / [COPY] button: OFF ([FAX] LED: ON / [COPY] LED: OFF) Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Exit sensor Paper present No paper Cover interlock switch (front cover (lower)) Door closed Door opened Toner bag full detection sensor Full...
Page 494
Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Original tray sensor Original present No original Original empty sensor Original present No original Jam access cover opening/closing sensor Cover opened Cover closed RADF opening/closing sensor RADF opened RADF closed Original exit sensor Original present...
Page 495
[FAX] button: OFF / [COPY] button: ON ([FAX] LED: OFF / [COPY] LED: ON) Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. Temperature/humidity sensor (displays Temperature [°C] temperature inside of the equipment) Temperature/humidity sensor (displays humidity Humidity [%RH] inside of the equipment) Drum thermistor (displays drum surface...
Page 496
Contents Digital Highlighted display Normal display Button Items to check e.g. e.g. USB Dongle for Printer/Scanner Kit (GM-2270) Connectable (*2) Not connectable USB Dongle for Printer Kit (GM-1250) Connectable Not connectable USB Dongle for Scanner Kit (GM-4250) Connectable Not connectable Dongles for other equipments / Other USB Connectable Not connectable...
Page 497
Output check (test mode 03) Code Function Code Function Procedure Drum motor ON (operational without Code No. 101 function OFF developer unit) New toner supply motor ON Code No. 102 function OFF (operational with developer unit) Polygonal motor (600 dpi) ON Code No.
Page 498
Code Function Procedure 1st drawer feed clutch ON/OFF 2nd drawer feed clutch ON/OFF Bypass feed clutch ON/OFF Tandem LCF pickup solenoid ON/OFF Tandem LCF end fence reciprocating movement Tandem LCF end fence motor ON/OFF 3rd drawer / Tandem LCF feed clutch (Tandem LCF model) ON/OFF 3rd drawer / Tandem LCF transport clutch ON/OFF Key copy counter count-up Horizontal transport section drive clutch-2 ON/OFF...
Page 499
Code Function Procedure RADF original feed motor ON/OFF (normal rotation) RADF original feed motor ON/OFF (reverse rotation) RADF read motor ON/OFF RADF original exit motor ON/OFF (normal rotation) RADF original exit motor ON/OFF (reverse rotation) RADF original reverse motor (normal rotation) ON/OFF RADF original reverse motor (reverse rotation) ON/OFF RADF original reverse solenoid ON/OFF Laser unit cooling fan (high speed) ON/OFF...
Page 500
Test print mode (test mode 04) Code Types of test pattern Remarks Output for Secondary scanning direction 17 gradation Error diffusion / gamma adjustment steps pattern Grid pattern Pattern width: 2 dots, Pitch: 10 mm Laser array break pattern e-STUIDIO557/657/757/857...
Page 501
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Process Developer 2000 Automatic adjustment The adjustment starts approx. 3 minutes after this t mode of auto-toner sensor mode has been selected, and then the value is automatically adjusted.
Page 502
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Process Image 2136 Low density pattern 0-1023 The value of the low density pattern detected at the t mode quality sensor output value image quality closed-loop control is displayed.
Page 503
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Process Image 2188 Image quality open- When a service call has occurred or a warning t mode quality loop control message (IQC/SPC) has appeared, "Image quality control enforcement...
Page 504
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Scanner Scanner Reproduction ratio 3032 Adj. secondary 0-255 SYS When the value increases by "1", the reproduction ratio t mode adjustment scan.direction in the secondary scanning direction (vertical to paper...
Page 505
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Scanner Scanner Data transfer of 3203 SLG board -> SYS SYS Transfers the characteristic values of the scanner t mode characteristic value board (shading correction factor / RGB color correction /...
Page 506
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Scanner Scanner Size detection of 3237 Starting time 0-255 SYS Adjusts the starting time of lamp lighting when the t mode original adjustment of lamp...
Page 507
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Image Adjustment of drawer 4018 4th drawer 0-255 When the value increases by "1", the image shifts t mode sideways deviation toward the front side by 0.0423 mm.
Page 508
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Image Left margin 4055 0-255 When the value increases by "1", the blank area t mode adjustment(blank becomes wider by approx.0.0423 mm. area at the left of the paper along the paper feeding direction)
Page 509
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 1st drawer 4100 Plain paper; Long 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 510
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 2nd drawer 4101 Plain paper; Middle 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 511
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Bypass feeding 4103 Plain paper; Short 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 512
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Bypass feeding 4104 Thick paper1; Short 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 513
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Bypass feeding 4105 Thick paper2; Short 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 514
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Bypass feeding 4107 OHP film; Long size 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 515
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 3rd drawer 4108 Plain paper; Middle 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 516
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4th drawer 4109 Plain paper; Short 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 517
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4110 Plain paper; Short 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment size2...
Page 518
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 1st drawer 4115 Thick paper1; Long 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 519
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 2nd drawer 4116 Thick paper1; Middle 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 520
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 3rd drawer 4117 Thick paper1; Short 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 521
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4th drawer 4118 Thick paper1; Short 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 522
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Tandem LCF 4119 OHP film 0-63 When the value increases by "1", the aligning amount t mode system/Pa amount adjustment...
Page 523
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Finisher Fine adjustment of 4150 -14-14 When the value increases by "1", the binding/folding t mode binding position shifts toward the right page by 0.25 mm. position/folding position Adjustmen...
Page 524
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Paper Adjustment of 4491 2nd drawer Refer to 0-31 <Default value> t mode feeding remained paper contents NAD: 18 amount (no paper Others: 20 remained)
Page 525
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Drive Transfer belt motor Fine adjustment of 4528 0-255 t mode rotation speed Adjustmen Printer Drive Fuser roller Fine adjustment of 4529 0-255...
Page 526
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Drive Fine adjustment of 4539 Normal speed Refer to 0-255 <Default Value> t mode reverse motor rotation contents e-STUDIO557/657: 137 speed e-STUDIO757/857: 135...
Page 527
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Drive Fine adjustment of 4542 Option LCF feeding 0-255 t mode transport motor speed rotation speed Adjustmen Printer Drive Fine adjustment of 4543...
Page 528
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Paper Leading edge position 4562 Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (1st drawer) Adjustmen Printer...
Page 529
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Paper Leading edge position 4564 Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (3rd drawer) Adjustmen Printer...
Page 530
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Paper Leading edge position 4566 Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (Tandem LCF) Adjustmen Printer...
Page 531
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Paper Leading edge position 4568 Thick paper 1 0-40 t mode feeding adjustment correction item on each media type (ADU) Adjustmen Printer...
Page 532
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4579 Using icons The paper feeding aligning amount is adjusted by t mode system/Pa amount adjustment pressing buttons on the LCD.
Page 533
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 1st drawer 4582 Thick paper2; Middle Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 534
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 2nd drawer 4583 Thick paper2; Long Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 535
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 2nd drawer 4583 Thick paper2; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 536
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 3rd drawer 4584 Thick paper2; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 537
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4th drawer 4585 Thick paper2; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 538
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning Option LCF 4586 Thick paper2; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 539
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4587 Thick paper2; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 540
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 1st drawer 4588 Thick paper3; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 541
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 2nd drawer 4589 Thick paper3; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 542
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 3rd drawer 4590 Thick paper3; Middle Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 543
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4th drawer 4591 Thick paper3; Long Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 544
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4th drawer 4591 Thick paper3; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 545
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4593 Thick paper3; Short Refer to 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 546
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 1st drawer 4594 OHP film; Middle size 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 547
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 2nd drawer 4595 OHP film; Short size1 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 548
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 3rd drawer 4596 OHP film; Short size2 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 549
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4th drawer 4597 OHP film; Short size3 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 550
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Printer Feeding Paper aligning 4599 OHP film; Short size3 0-63 When the value increases by " 1 ", the aligning amount t mode system/Pa amount adjustment...
Page 551
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Backgroun PPC(black) 7102 Photo 0-255 SYS The larger the value, the darker the background t mode Processin becomes. The smaller the value, the lighter the adjustmen background becomes.
Page 552
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image ADF noise PPC(black) 7152 Text 0-200 SYS When the value decreases, the effect of reducing t mode Processin reduction streaks (set with 08-7617) becomes larger.
Page 553
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma PPC(black) Photo 7192 Low density 0-255 SYS The larger the value, the darker the image of the area t mode Processin balance...
Page 554
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Image PPC(black) Text 7213 Beam level 1/4 0-255 The smaller the value, the narrower the beam width t mode Processin contrast becomes and the smaller the dots are reproduced.
Page 555
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Image PPC(black) Photo 7214 Beam level 3/4 Refer to 0-255 The smaller the value, the narrower the beam width t mode Processin contrast...
Page 556
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Range PPC(black) Black/Manual density 7287 Text SYS 0: Background peak - Fixed t mode Processin correction adjustment 1: Background peak - Varied adjustmen Adjustmen Image...
Page 557
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma PRT(black) PCL/Detail/600dpi 7318 Medium density 0-255 SYS When the value increases, the density in the target t mode Processin balance area becomes higher.
Page 558
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Image Black NW printer Toner saving OFF 7330 Normal printing Refer to 0-255 The smaller the value, the narrower the beam width t mode Processin contrast...
Page 559
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma Monochrome/600dpi/ PS/text 7360 High density 0-255 SYS Larger the value, the density for the target area t mode Processin balance Auto...
Page 560
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma Monochrome/600dpi/ XPS/graphics 7367 Medium density 0-255 SYS Larger the value, the density for the target area t mode Processin balance Auto...
Page 561
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image ADF noise SCN(black) 7403 Photo 0-200 SYS When the value decreases, the effect of reducing t mode Processin reduction streaks (set with 08-8300) becomes larger.
Page 562
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Density SCN(black) Manual 7444 Text/Photo 0-255 SYS The larger the value, the darker the image at the center t mode Processin adjustmen...
Page 563
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Gamma SCN(black) Text/Photo 7485 Low density 0-255 SYS The larger the value, the darker the image of the area t mode Processin balance...
Page 564
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Density FAX(black) Manual 7534 Text 0-255 SYS The larger the value, the lighter the image at the center t mode Processin adjustmen...
Page 565
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Stroke PS/PDF automatic 600dpi 8239 Default setting SYS This code is used to change the width of fine lines in t mode Processin adjustmen...
Page 566
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image Backgroun SCN (color) 8309 Text/Photo 0-255 SYS The smaller the value, the lighter the background t mode Processin d fine becomes.
Page 567
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image SCN(color) 8321 Printed image SYS Sets the color space format of the output image. t mode Processin conversion 0: sRGB method 1: AppleRGB...
Page 568
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen Image SCN(color) 8372 User custom SYS Sets the color space format of the output image. t mode Processin conversion 0: sRGB method 1: AppleRGB...
Page 569
Sub- Default Acceptable Proce Servic 05/08 Mode Element Item Subitem Code Details Contents element code value value dure e UI Adjustmen System Maintenan 9043 Equipment number SYS When this adjustment is performed with this code, the t mode (serial number) entry setting code (08-9601) is also performed automatically.
Page 570
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser 2002 Fuser unit counter 0~29 0: No error 1: C411 2: C412 3: C443 4: - 5: Mode C445/465 6: C446/466 7: C447/467 8: C468 9: C449 10: C475 11: C471 12: C472 13: C473 14: C481 15:...
Page 571
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Fuser roller Plain paper 2010 Low temperature Refer to 0~14 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: Mode temperature during contents...
Page 572
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low temperature Temperature setting 2030 Thick paper 3 Refer to 0~12 Sets the temperature at which low-temperature Mode waiting contents...
Page 573
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Energy Saving Mode 2042 Fuser roller Refer to 0~27 0: OFF 1: 50°C 2: 55°C 3: 60°C 4: 65°C 5: 70°C 6: Mode temperature contents...
Page 574
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Pre-running time for 2054 Thick paper 1 Refer to 0~15 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 Mode first printing contents...
Page 575
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser 2060 Threshold of low 0~11 The boundary temperature of the low and normal Mode temperature temperature control can be set. environment control 0: 0°C 1: 5°C 2: 9°C 3: 10°C 4: 12°C 5: 14°C 6: 15°...
Page 576
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low temperature Temperature setting 2080 Plain paper Refer to 0~12 Sets the temperature at which low-temperature Mode waiting (Normal temperature contents...
Page 577
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low temperature Temperature setting 2081 Thick paper 2 Refer to 0~12 Sets the temperature at which low-temperature Mode waiting contents...
Page 578
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low temperature Temperature setting 2087 Plain paper Refer to 0~12 Sets the temperature at which low-temperature Mode waiting (Low temperature contents...
Page 579
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low temperature Temperature setting 2088 OHP film Refer to 0~12 Sets the temperature at which low-temperature Mode waiting contents warming-up control starts.
Page 580
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Switching timing into 2130 Pressure roller 0~12 0: Switching disabled 1: 5 min. 2: 10 min. 3: 20 min. Mode low-speed pre- 4: 30 min.
Page 581
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Temperature setting 2202 Thick1(Low Refer to 0~12 Sets the temperature at which low-temperature Mode waiting temperature contents warming-up control starts.
Page 582
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Temperature addition 2226 Plain paper SSets whether the temperature is raised or not in the Mode waiting (Normal temperature low-temperature warming-up control mode.
Page 583
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Temperature addition 2226 Thick paper 1 SSets whether the temperature is raised or not in the Mode waiting (Low temperature...
Page 584
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Temperature 2236 Plain(Normal Refer to Sets the temperature to be added to the setting Mode waiting additional value temperature contents...
Page 585
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Temperature 2237 Plain(Low Refer to Sets the temperature to be added to the setting Mode waiting additional value temperature contents...
Page 586
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Starting temperature 2238 Thick1(Normal Refer to 0~12 Sets the temperature to be added to the setting Mode waiting while the temperature...
Page 587
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Starting temperature 2239 Thick1(Low Refer to 0~12 Sets the temperature to be added to the setting Mode waiting while the temperature...
Page 588
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Starting temperature 2240 Thick2(Temperature Refer to 0~12 Sets the temperature to be added to the setting Mode waiting while the temperature...
Page 589
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Starting temperature 2241 Thick3(Temperature Refer to 0~12 Sets the temperature to be added to the setting Mode waiting while the temperature...
Page 590
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Switching printing 2244 Thick paper 2 0: Disabled 1: Enabled only for 5 minutes after Mode speed warming-up 2: Always enabled Setting Process...
Page 591
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding Classification by the 2271 Threshold of number 0~10000 The threshold of the number of pixels to control the Mode amount control when number of pixels...
Page 592
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding The continuous 2272 The number of pixels 0~100 Feeding amount = setting value * 0.3 (mm) Mode amount control when printing number is...
Page 593
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding The continuous 2272 The number of pixels 0~100 Feeding amount = setting value * 0.3 (mm) Mode amount control when printing number is...
Page 594
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding The continuous 2272 The number of pixels 0~100 Feeding amount = setting value * 0.3 (mm) Mode amount control when printing number is...
Page 595
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding The continuous 2273 The number of pixels 0~100 Feeding amount = setting value * 0.3 (mm) Mode amount control when printing number is...
Page 596
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding The continuous 2273 The number of pixels 0~100 Feeding amount = setting value * 0.3 (mm) Mode amount control when printing number is...
Page 597
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding The continuous 2273 The number of pixels 0~100 Feeding amount = setting value * 0.3 (mm) Mode amount control when printing number is...
Page 598
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Cleaning web feeding The continuous 2273 The number of pixels 0~100 Feeding amount = setting value * 0.3 (mm) Mode amount control when printing number is...
Page 599
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Process 2818 Toner supply amount The supply amount of recycle toner to the developer Mode correction/ Hopper unit (the drive counts of the hopper motor) is corrected. motor control Smaller<-Toner supply amount->Larger 3->1->0->7->6->5->4->8->2...
Page 600
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Image Drum surface 2851 Control setting 0: Enabled 1: Disabled Mode quality potential sensor control Setting Process Image 2873 Number of times of 0~16...
Page 601
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Image 2900 Contrast voltage 0~999 The lower limit of the developer contrast voltage control Mode quality lower limiter is set.[Unit: V] control Setting...
Page 602
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Image 2911 Image quality control 0: Enabled Mode quality auto-start 1: Disabled control setting(Specified number of sheets have been printed from first image quality control start in a day or warming-up...
Page 603
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Transfer Transfer correction Thick paper2 2930 0~255 The output value of the transfer bias at the trailing edge Mode value of paper is corrected.
Page 604
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Transfer Transfer timing Thick paper3 2961 0~255 Mode correction Setting Process Transfer Transfer timing Thick paper3 2961 0~255 Mode correction Setting...
Page 605
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Scanner RADF 3021 Setting for switchback SYS This setting is whether the original length is detected or Mode operation in mixed- not by transporting without scanning in reverse when size copying using A4-R/FOLIO paper or LT-R/LG paper is detected in a...
Page 606
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Card reader 3500 Device setting SYS To enable the e-Bridge ID Gate, a card reading device Mode interface 429496729 should be set in the order of "ABYYZZZZ".
Page 607
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Card reader 3502 Format information 2 SYS The data of the block number in the noncontact IC is Mode interface 429496729...
Page 608
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General Real time log 3626 Department SYS Sets whether the department information (number, Mode notification function information name, code) is transmitted or not in the real time log transmission setting notification function.
Page 609
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 3642 User authentication SYS 0: Authentication with user name and domain name mode setting for NW 1: No authentication control in the equipment print/NW fax/Internet 2: Authentication with user name fax function...
Page 610
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 3653 Judgment timing for SYS Sets the timing for judging whether following job is mode continuous printing printed continuously or not.
Page 611
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Scanning 3662 Waiting period for SYS 0: Disabled 1: Enabled mode continue after the * When "Enabled" is set, the screen to notify continuity RADF scanning appears for 1 second after RADF scanning has been completed.
Page 612
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 3724 Windows domain NIC Sets the Windows domain authentication method for Mode authentication of device authentication, Scan to SMB, and user device/user authentication.
Page 613
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 3736 DNS Client Time Out 1~180 NIC Use when a timeout occurred at DNS client connection Mode Setting System Network...
Page 614
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network IPv6 3772 Default Gateway Sets the default gateway for IPv6 address. Maximum Mode setting 40 characters (byte). Setting System Network...
Page 615
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Scanner 3805 Department SYS Department Management is set when Remote Scan is Mode Management setting performed. by Remote Scan 0: w/o GUI OFF,w/ GUI OFF 1: w/o GUI ON,w/ GUI OFF 2: w/o GUI OFF,w/ GUI ON...
Page 616
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 3833 Home directory SYS Function to store a file in the user's home directory. Mode function 0: Disabled 1: Enabled Setting System General...
Page 617
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 3853 Summer time mode SYS Summer time is started as follows when 08-3852 is Mode Offset value enabled.
Page 618
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 3859 Summer time mode Refer to 1~12 SYS The month in which summer time is ended is set. Mode Ending month contents...
Page 619
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System 3875 Address confirmation Refer to SYS Enable this setting to display the address confirmation Mode for multiple contents screen before sending fax to prevent wrong destinations transmission when multiple destination addresses are...
Page 620
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Laser 4015 Timing of auto- SYS This setting to switch the polygonal motor to the Mode clearing of polygonal standby rotation when a certain period of time has motor pre-running passed from the pre-running.
Page 621
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Paper Feeding retry number 3rd drawer 4022 Plain paper Sets the number of times of the feeding retry from the Mode feeding setting...
Page 622
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Paper 4101 Paper size for 2nd Refer to 0~255 Press the button on the LCD to select the size. Mode feeding drawer...
Page 623
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Paper 4104 Paper size setting Refer to 0~255 Press the button on the LCD to select the size. Mode feeding /Tandem LCF...
Page 624
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Paper 4114 Paper size (ST-R) 216/140 182~432/1 Mode feeding feeding/widthwise 40~297 direction Setting Printer Paper 4115 Paper size 356/257 182~432/1 Mode feeding...
Page 625
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Paper 4131 Feeding retry setting 0: Enabled Mode feeding 1: Disabled * When the value of 08-9016 is set to "5", the value of this code is automatically set to "1".
Page 626
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Fuser 4532 Fusing error 0~255 Mode temperature (Temperature of the fuser roller front thermopiles) Setting Printer Fuser 4533 Fusing error 0~255 Mode...
Page 627
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer General 4586 Checking of NVRAM Refer to 320-323 <Default value> Mode board data on LGC content 320: e-STUDIO557 board No.
Page 628
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer All clearing Destination 4659 Storing area for SYS Refer to 0-255 Stores SYS-SRAM destination data when code 08- Mode destination contents...
Page 629
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Counter Tray-up abnormality 2nd drawer 4669 2 times in a row 0~255 Displays the number of the tray-up abnormality Mode occurrences which are generated 2 times in a row.
Page 630
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Counter Tray-up abnormality 4th drawer 4671 2 times in a row 0~255 Displays the number of the tray-up abnormality Mode occurrences which are generated 2 times in a row.
Page 631
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Printer Paper Pre-push control of 4741 Thick paper 3 Suppresses the unevenness in the positions of the mode feeding middle paper feeding leading edge of the image in the thick paper 3 mode.
Page 632
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Additional 5412 Plain paper Refer to 0~11 Sets for how many minutes the temperature is added Mode waiting temperature rising...
Page 633
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Process Fuser Low-temperature Additional 5412 Thick paper 1 Refer to 0~11 Sets for how many minutes the temperature is added Mode waiting temperature rising...
Page 634
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Maintenan 5554 Setting value of PM Refer to 8 digits <Default value> Mode counter content e-STUDIO557: JPC: 0 Others: 460,000 e-STUDIO657: JPC: 0...
Page 635
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Maintenan 5568 Current value of PM 8 digits Counts up when the registration sensor is ON. Mode counter Display/0 clearing Setting Counter...
Page 636
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Double For fee charging Paper size 6010 Large-sized paper Refer to 0: Counted as 1 1: Counted as 2 2: Counted as 1 Mode count contents...
Page 637
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Counter Display of number of 6064 Large 8 digits SYS Counts the number of output pages in the Printer Mode output pages in Function...
Page 638
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Counter Display of number of 6066 Small 8 digits SYS Counts the number of output pages in the FAX Mode output pages in FAX Function according to its size (large/small).
Page 639
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Counter Display of number of 6071 Large 8 digits SYS Counts the number of scanning pages in the FAX Mode scanning pages in Function according to its size (large/small).
Page 640
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Counter Display of number of 6073 Small 8 digits SYS Counts the number of transmitted pages in the FAX Mode transmitted pages in Function according to its size (large/small).
Page 641
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Double 6083 Thick1/2/3/4 (Back) Refer to SYS Sets the weight of fee charging count for printing per Mode count contents page.
Page 642
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Double 6083 Tab paper Refer to SYS Sets the weight of fee charging count for printing per Mode count contents page.
Page 643
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Counter 6087 Color/Black quota SYS When the pages are counted for twin/mono color Mode Settings selection at counter, this code sets whether the pages are twin/mono color count subtracted from ColorQuota or BlackQuota.
Page 644
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Custom For dealer Weighting/Print 6089 Black/Large 0-9999 SYS Weights addition of print to Custom Counter (Total Mode counter Counter).
Page 645
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Counter of 6118 Option LCF 8 digits Counts the number of sheets fed from the Option LCF. Mode Paper feed Setting Counter...
Page 646
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Maintenan 6198 Switching of PM The PM timing can be displayed in these 2 methods. Mode timing display/ Output (Messages will appear on the LCD panel.) pages or drive counts 0: PM counter (Number of output pages can be set in...
Page 647
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Paper Feeding retry counter 6231 2nd drawer 8 digits Counts the number of times of the feeding retry from Mode feeding the 2nd drawer.
Page 648
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Paper 6240 Feeding retry counter 8 digits When the number of feeding retry (08-6230 to 08-6235) Mode feeding upper limit exceeds the setting value, the feeding retry will not be value(Bypass feed)
Page 649
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Photoconductive 6250 Present number of 8 digits mode counter drum output pages Setting Counter Photoconductive 6250 Recommended Refer to 8 digits <Default value>...
Page 650
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Drum cleaning blade 6258 Present driving 8 digits mode counter counts Setting Counter Drum cleaning blade 6258 Recommended Refer to 8 digits <Default value>...
Page 651
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Drum cleaning brush 6266 Present driving 8 digits mode counter counts for control Setting Counter Drum cleaning brush 6266 Number of times 8 digits...
Page 652
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Main charger grid 6274 Recommended Refer to 8 digits <Default value> mode counter number of output contents e-STUDIO557: 460,000 pages for e-STUDIO657: 515,000 replacement...
Page 653
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Main charger wire 6282 Recommended Refer to 8 digits <Default value> mode counter driving counts to be contents e-STUDIO557/657: 495,000 replaced e-STUDIO757/857: 410,000...
Page 654
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Main charger wire 6290 Number of times 8 digits mode counter cleaning pad replaced Setting Counter Main charger wire 6291 Date of previous 8 digits...
Page 655
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Developer material 6300 Recommended Refer to 8 digits <Default value> mode counter number of output contents e-STUDIO557: 460,000 pages for e-STUDIO657: 515,000 replacement...
Page 656
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Toner filter 6308 Recommended Refer to 8 digits <Default value> mode counter driving counts to be contents e-STUDIO557/657: 400,000 replaced e-STUDIO757/857: 330,000 Setting...
Page 657
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Transfer belt 6328 Present number of 8 digits mode counter output pages Setting Counter Transfer belt 6328 Recommended Refer to 8 digits <Default value>...
Page 658
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Transfer belt cleaning 6332 Present driving 8 digits mode counter blade counts Setting Counter Transfer belt cleaning 6332 Recommended Refer to 8 digits...
Page 659
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Fuser roller 6346 Recommended Refer to 8 digits <Default value> mode counter number of output contents e-STUDIO557: 460,000 pages for e-STUDIO657: 515,000 replacement...
Page 660
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pressure roller 6350 Recommended Refer to 8 digits <Default value> mode counter driving counts to be contents e-STUDIO557: 470,000 replaced e-STUDIO657: 940,000 e-STUDIO757/857: 780,000...
Page 661
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Cleaning web 6352 Present driving 8 digits mode counter counts for control Setting Counter Cleaning web 6352 Number of times 8 digits mode counter...
Page 662
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Fuser roller 6368 Recommended Refer to 8 digits <Default value> mode counter separation finger number of output contents e-STUDIO557: 460,000 pages for e-STUDIO657: 515,000...
Page 663
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Feed roller (RADF) 6384 Present number of 8 digits mode counter output pages Setting Counter Feed roller (RADF) 6384 Recommended 120,000...
Page 664
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pickup roller (1st 6390 Present number of 8 digits mode counter drawer) output pages Setting Counter Pickup roller (1st 6390 Recommended 200,000...
Page 665
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Feed roller (Tandem 6396 Present number of 8 digits mode counter LCF) output pages Setting Counter Feed roller (Tandem 6396 Recommended 400,000...
Page 666
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Feed roller (Option 6402 Present number of 8 digits mode counter LCF) output pages Setting Counter Feed roller (Option 6402 Recommended 500,000...
Page 667
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Separation roller (2nd 6408 Present number of 8 digits mode counter drawer) output pages Setting Counter Separation roller (2nd 6408 Recommended 200,000...
Page 668
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Separation roller (4th 6414 Present number of 8 digits mode counter drawer) output pages Setting Counter Separation roller (4th 6414 Recommended 200,000...
Page 669
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Feed roller (4th 6422 Present number of 8 digits mode counter drawer) output pages Setting Counter Feed roller (4th 6422 Recommended 200,000...
Page 670
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pickup roller (4th 6430 Present number of 8 digits mode counter drawer) output pages Setting Counter Pickup roller (4th 6430 Recommended 200,000...
Page 671
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Web roller one-way 6438 Recommended Refer to 8 digits <Default value> mode counter clutch driving counts to be contents e-STUDIO557/657: 470,000 replaced...
Page 672
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pixel 6504 Pixel counter display SYS Selects whether or not to display the pixel counter on Mode counter setting the LCD screen.
Page 673
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pixel Number of output 6561 8 digits SYS Counts the number of output pages converted to the Mode counter pages(Service standard paper size in the FAX function and service...
Page 674
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pixel Latest pixel 6618 0~10000 SYS Displays the latest pixel count in the FAX function and Mode counter count(Service service technician reference.[Unit: 0.01%] technician reference)
Page 675
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pixel Pixel count 6721 20.1-25% 8 digits SYS The pixel count data are divided into 10 ranges. The Mode counter distribution...
Page 676
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pixel Pixel count 6722 25.1-30% 8 digits SYS The pixel count data are divided into 10 ranges. The Mode counter distribution...
Page 677
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Counter Pixel Pixel count 6723 30.1-40% 8 digits SYS The pixel count data are divided into 10 ranges. The Mode counter distribution...
Page 678
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Image Automatic Last updated date 7051 Monochrome PPC SYS Last updated date and time of automatic tone Mode Processin tone and time 421231235...
Page 679
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting Image User User custom mode NW SCN 8303 Color SYS 0: Unused Mode Processin interface setting 1: Text/Photo base 2: Text base 3: Photo base 4: e-document base...
Page 680
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 8519 Scan PDF file Paper SYS 0: Equivalent to scan image size Mode size 1: Fitted into any standard size Setting System General...
Page 681
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 8538 Toner near empty SYS 0: Disabled Mode interface notification setting 1: Enabled Setting System General 8540 Date and time format SYS 0: YYYY/MM/DDhh:mm:ss.mmm Mode...
Page 682
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System LDAP user Attribute value setting 8592 Sender address mail SYS Sets the default attribute value of sender address. Mode authenticat Maximum 32 characters (ASCII).
Page 683
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network Prioritized 8610 Card 0-100 SYS Sets the prioritized authentication server to be Mode authentication server searched (0 to 100). The servers displayed on the screen accessed by TopAccess ->...
Page 684
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 8640 Job build operation SYS This setting enables user to use the job build function mode interface when the coin when the coin controller is connected.
Page 685
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Card reading device LDAP authentication 8653 LDAP attribute name eBMUse SYS Maximum 32 characters (ASCII). Mode interface settings 13 rCard Setting...
Page 686
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 8670 e-Filing print setting SYS 0: Not allowed Mode when key 1: Allowed counter/totalizer is installed Setting System Network Number of retry for...
Page 687
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 8704 Restriction of SYS This code is used to restrict Email/FAX Address to Mode interface Email/FAX address LDAP server specified via TopAccess.
Page 688
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Service notification 8715 Password for zip file #104810 SYS Password for zip file with password of service Mode interface information...
Page 689
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 8722 Display method of SYS Sets the display method of error if the Home Directory Mode interface "Cannot find the for user cannot be obtained from the server when Home Directory"...
Page 690
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Forced 8728 Display/Non-display SYS 0: Disabled 1: Enabled Mode printing of setting in TopAccess user name Setting System Forced 8728 Enable/Disable...
Page 691
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Forced 8728 Font size setting 6-16 SYS Normally this setting is made in TopAccess. Mode printing of 6-16pt. user name Setting System...
Page 692
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 8745 Enable/Disable SYS Sets whether part of the cookie, password, and form Mode interface setting of EWB history data of user who logs in to EWB is saved or not.
Page 693
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan Display of remaining 8762 0-100 SYS 0 to 100% Mode amount of toner (for RDMS/MMDT) Setting System Network 8771 Account setting for...
Page 694
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General Interval setting Transition to Super 8782 For fax 15-600 SYS Sets the interval to shift to Super Sleep again after mode Sleep recovery from Super Sleep.
Page 695
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 8791 Transition to sleep SYS This code sets whether the equipment shifts to the Mode mode after printing sleep mode again immediately after completion of printing when the equipment recovers from the super- sleep mode for network printing.
Page 696
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 8824 FTP client mode NIC Sets the FTP transfer mode when FTP is selected for mode "FILE" to save the scanned data. 0: Automatic 1: Passive mode 2: Active mode...
Page 697
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 8836 Time-out period for 1-180 NIC Sets the time-out period for the SMB client connection mode SMB client to a server.
Page 698
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Continuou 8906 Copy SYS 0: OFF (copying not continued) Mode s print 1: ON (copying continued by canceling punching setting setting) when...
Page 699
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System 8914 SYS Sets whether the Fax function is enabled or disabled. Mode function 0: Disabled setting 1: Enabled Setting System 8914...
Page 700
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System 8914 Save as SMB SYS Sets whether the function that saves scanned data of Mode function originals to the SMB server is enabled or disabled. setting 0: Disabled 1: Enabled...
Page 701
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Option 8920 Output tray for SYS Selects the bin/tray to which the paper is output. Mode FAX/InternetFAX/e- 0: Finisher 1st bin mail printing 1: Finisher 1st bin 2: Finisher 2nd bin...
Page 702
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Off Device 8931 Output Management SYS 0: Disabled Mode interface Customization Service setting 1: Enabled Architecture Setting System User 8932...
Page 703
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Feeding 8967 Rotation printing by SYS If the printing size and the guides width of the bypass Mode system / guides width of feed tray are different, it is judged that paper is set in...
Page 704
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General Detection of originals 8977 Copy SYS Sets whether the originals that are prohibited from Mode prohibited from duplication are detected or not.
Page 705
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General Scheduled automatic 8981 Day of the week 0-255 SYS Sets the condition and day of the week for scheduled Mode reboot automatic reboot.
Page 706
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User NFC reader 8987 Format information 1 SYS 000ASSSS (hexadecimal, first 3 digits are fixed) Mode interface 429496729 0: A key 1: B key -SSSS:...
Page 707
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan Notification of Notification day of the 8994 Notification day of the 0-127 SYS Input the value which corresponds to the day of the Mode equipment week...
Page 708
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan Notification of Error history list 8999 Latest 80 items SYS 0: Disabled Mode equipment 1: Enabled information Setting System Maintenan...
Page 709
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9012 Language displayed Refer to SYS <Default value> Mode interface at power-ON contents JPC: Japanese TWD: Traditional Chinese CND: Simplified Chinese KRD: Korean Others: English...
Page 710
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 9023 Trial period setting 1~60 SYS Sets the trial period from 1 to 60 days. This setting is Mode effective only when the default value is "254".
Page 711
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 9081 Initialization of SYS Initializing of the department management information Mode department * Key in the code and press the [INITIALIZE] button to management perform the initialization.
Page 712
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 9103 Time differences Refer to 0~47 SYS 0: +12.0h 1: +11.5h 2: +11.0h 3: +10.5h 4: +10.0h 5: Mode contents +9.5h 6: +9.0h 7: +8.5h 8: +8.0h 9: +7.5h 10: +7.0h 11:...
Page 713
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9114 Power saving mode SYS 0: Off mode 1: Sleep mode Mode interface Setting System General Raw printing job 9117 Do not Print Blank SYS 0: Disabled 1: Enabled...
Page 714
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Default mode setting Default mode setting 9132 Default setting of 0-99 SYS Sets the screen to be displayed after the auto-clear Mode interface screen (Function)
Page 715
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9140 Paper size selection Refer to 0~255 SYS Press the button on the LCD to select the size. Mode interface for [OTHER] button...
Page 716
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9152 Correction of 0~10 SYS Sets the reproduction ratio for the "X in 1" printing Mode interface reproduction ratio in (including magazine sort) to the "Reproduction ratio x editing copy...
Page 717
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9163 Direction priority for SYS 0: Short edge 1: Long edge Mode interface date and time stamp printing Setting System...
Page 718
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Feeding paper media 9185 Copier 1~113 SYS <Acceptable value (decimal number)> Mode interface 1,16,17,32,33,48,49,64,65,80,81,96,97,112,113 Each bit 0: Excluded from feeding target media Each bit 1: Feeding target media bit 0: Plain paper bit 1: N/A (always set "0") bit 2: N/A (always set "0") bit 3: N/A (always set "0") bit 4: Thick...
Page 719
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9204 Binarizing level SYS 0: Step -2 Mode interface selection (When 1: Step -1 judging as black in 2: Step 0 (center) the ACS Mode) 3: Step 1...
Page 720
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Default mode setting Default setting of 9216 Full Color SYS 0: 100 dpi Mode interface resolution (SCN) 1: 150 dpi 2: 200 dpi 3: 300 dpi...
Page 721
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9226 Default setting of SYS 1: Step -4 2: Step -3 3: Step -2 4: Step -1 5: Step 0 Mode interface background...
Page 722
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Image Binarizing level 9230 Step +2 0-255 SYS Sets the binarizing level of each step. When the value Mode setting (When judging increases, the image becomes darker.
Page 723
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Data 9240 HDD data overwriting SYS Select the type of the overwriting level for deleting HDD Mode overwrite type setting data.
Page 724
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Option 9255 FOLIO/A4-R SYS When the value of this code is "0", the paper size is Mode judgment when width judged by performing switchback.
Page 725
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9274 "From" address SYS 0: "User name" + @ + "Domain name" Mode assignment method 1: LDAP search when it is given an 2: Use the address registered in "From"...
Page 726
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9298 Restriction on SYS Some restrictions can be given on the administrator for Mode Address book operating the Address book. operation by 0: No restriction 1: Can be operated only under the administrator...
Page 727
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Paper 9306 LT <-> A4/LD <-> A3 SYS Sets to whether to print a document in a different paper Mode feeding size from the one selected if there is no drawer which...
Page 728
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9312 Raw printing job SYS 0: Valid 1: Invalid Mode (Staple) Setting System Network 9313 Raw printing SYS 0: Inner tray Mode job(receiving tray)
Page 729
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Paper 9321 Memory 4 Paper size 148/100 148~432/1 SYS Registers the paper size of bypass feed (non-standard Mode feeding (bypass feeding/non- 00~297...
Page 730
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9334 PCL line feed code SYS Sets the PCL line feed code. Mode setting 0: Automatic setting 1: CR=CR, LF=LF 2: CR=CR+LF, LF=LF 3: CR=CR, LF=CR+LF...
Page 731
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Binding margin 9341 Top binding front 0-100 SYS Sets the binding margin displayed as default on the Mode interface setting...
Page 732
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9370 Taiwan watermark SYS 0: Disabled Mode interface 1: Enabled Setting System User 9379 AES data encryption SYS 0: Encryption invalid Mode interface...
Page 733
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9388 Date display format of SYS Sets the data display format of the file of "Save as file" Mode the file name of "Save and Email transmission.
Page 734
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network Address 9406 Address Mode NIC 1: Fixed IP address Mode 2: Dynamic IP address 3: Dynamic IP address without Auto IP Setting System Network...
Page 735
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9430 Availability of HTTP NIC 1: Available 2: Not available Mode server Setting System Network 9437 Availability of SMTP NIC 1: Available 2: Not available Mode client...
Page 736
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9505 Bonjour setting NIC 1: Valid 2: Invalid Mode Setting System Network 9515 Windows domain UTY Maximum 128 letters Mode No.1 of user authentication...
Page 737
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network Enabling server's IP 9584 SMTP Server Option 1: Enabled 2: Disabled Mode address acquired by (69) Simple Mail This value is used only when DHCP is enabled.
Page 738
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan 9610 Remote-controlled 0~31 SYS 0: OFF 1 to 31: 1st to 31st of a month Mode service polling day selection Day-1 Setting System...
Page 739
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan 9624 Information of SYS 0: Invalid 1: Valid Mode supplies setting of toner cartridge Setting System Maintenan 9625 Information about SYS 0: Disabled 1: Enabled...
Page 740
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan General 9700 Service technician 32 digits SYS A telephone number can be entered up to 32 digits. Mode telephone number Use the [Pause] button to enter a hyphen (-).
Page 741
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan Remote-controlled Call /Display function 9730 Service center call SYS 0: OFF 1: Notifies all service calls 2: Notifies all but Mode service function...
Page 742
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan 9751 Automatic ordering SYS Maximum 32 digits Enter hyphen with the [Pause] Mode function of supplies button (Remote) FAX number Setting...
Page 743
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan 9764 Automatic ordering SYS Maximum 50 letters Mode function of supplies (Remote) Supplier's name Setting System Maintenan 9765 Automatic ordering SYS Maximum 100 letters...
Page 744
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Maintenan 9784 Counter notification SYS Maximum 32 digits Enter hyphen with the [PAUSE] Mode Remote FAX setting button. Setting System General...
Page 745
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 9799 Local authentication SYS Sets the authentication mode when "0: (Internal Mode mode switchover authentication)" is selected in the code 08-9293. 0: Card ID differs from the User ID 1: Card ID is the same as the User ID Setting...
Page 746
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Finisher Stapling setting 9811 Thick2 -50~50 SYS -50 to 50 Mode Maximum number of sheets acceptable exceeding upper limit / Long size Setting System...
Page 747
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User Off Device 9822 SSL port number 49630 0-65535 SYS Sets an SSL port number for remote scanning using Mode interface Customization...
Page 748
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System General 9881 Day of total counter 0~127 SYS Input the value which corresponds to the day of the Mode data transmission week.
Page 749
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Image 9897 Default value setting SYS 1: -4 2: -3 3: -2 4: -1 5: 0 6: +1 7: +2 8: +3 9: +4 Mode of background peak adjustment (Black)
Page 750
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Finisher Stapling setting 9937 Thick1 -100~100 SYS -100 to 100 Mode Acceptable number of sheets exceeding upper limit / Short size Setting System...
Page 751
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Version Engine 9941 Laser ROM version 320L-XXX If the laser ROM version is displayed as Mode "NGD" in this code, it denotes that the updating of the laser ROM failed.
Page 752
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9963 Display of receiving SYS 0: Disabled Mode interface job on PRINT/JOB 1: Enabled (Other user's receiving job can be deleted) STATUS screen 2: Enabled (Other user's receiving job cannot be deleted)
Page 753
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System Network 9980 Address setting for SYS Sets address of TO/CC/BCC when the user Mode TO/CC/BCC at authentication and E-mail authentication are enabled. authentication When the value of this code is set to "1", the address specified as From Address is input to TO destination...
Page 754
05/08 Mode Element Item Subitem Code Sub- Details Default Acceptable Contents Proce Servic element code value value dure e UI Setting System User 9987 Retention of fax SYS Sets whether the fax sending settings are retained or Mode interface sending settings not.