Kurzweil K2500 Reference Manual page 88

FXAlg #715: Dual MovDelay ¥ FXAlg #716: Quad MovDelay
PAGE 2
L Delay 0.0 to 1000.0 ms
L LFO Mode Flange, ...
L LFO Rate 0.00 to 10.00 Hz
L LFO Dpth 0.0 to 200.0%
L Feedback -100 to 100%
L HF Damp 16 to 25088 Hz
Parameters (Quad MovDelay):
PAGE 1
L Wet/Dry -100 to 100%wet
L Out Gain Off; -79.0 to 24.0 dB
L1 Mix -100 to 100%
L2 Mix -100 to 100%
PAGE 2
L1 Pan -100 to 100%
L2 Pan -100 to 100%
L Dry Pan -100 to 100%
L1/Dry->L2 0 to 100%
PAGE 3
L1 Delay 0.0 to 1000.0 ms
L1 LFO Mode Flange, ...
L1 LFO Rate 0.00 to 10.00 Hz
L1 LFO Dpth 0.0 to 200.0%
L1 Feedback -100 to 100%
L1 HF Damp 16 to 25088 Hz
PAGE 4
R1 Delay 0.0 to 1000.0 ms
R1 LFO Mode Flange, ...
R1 LFO Rate 0.00 to 10.00 Hz
R1 LFO Dpth 0.0 to 200.0%
R1 Feedback -100 to 100%
R1 HF Damp 16 to 25088 Hz
L Wet/Dry, R Wet/Dry
L Out Gain, R Out Gain
Algorithm Reference-88
R Delay
R LFO Mode
R LFO Rate
R LFO Dpth
R Feedback
R HF Damp
R Wet/Dry
R Out Gain
R1 Mix
R2 Mix
R1 Pan
R2 Pan
L Dry Pan
L1/Dry->L2
L2 Delay
L2 LFO Mode
L2 LFO Rate
L2 LFO Dpth
L2 Feedback
L2 HF Damp
R2 Delay
R2 LFO Mode
R2 LFO Rate
R2 LFO Dpth
R2 Feedback
R2 HF Damp
The relative amount of input signal and effected signal that is to appear in the Þnal effect
output mix for each input channel. When set to 0%, the output is taken only from the
corresponding input (dry) signal. When set to 100%, the output is all wet. Negative
values polarity-invert the wet signal.
The overall gain or amplitude at the output of the effect for each input channel.
0.0 to 1000.0 ms
Flange, ...
0.00 to 10.00 Hz
0.0 to 200.0%
-100 to 100%
16 to 25088 Hz
-100 to 100%wet
Off; -79.0 to 24.0 dB
-100 to 100%
-100 to 100%
-100 to 100%
-100 to 100%
-100 to 100%
0 to 100%
0.0 to 1000.0 ms
Flange, ...
0.00 to 10.00 Hz
0.0 to 200.0%
-100 to 100%
16 to 25088 Hz
0.0 to 1000.0 ms
Flange, ...
0.00 to 10.00 Hz
0.0 to 200.0%
-100 to 100%
16 to 25088 Hz