Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in your area call 1-800- 274-6848.
4. This Table Saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a Table Saw, do not use until proper training and knowledge has been obtained.
Page 6
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 21. Provide for adequate space surrounding work area and non-glare, overhead lighting. 22. Keep the floor around the machine clean and free of scrap material, oil and grease. 23. Keep visitors a safe distance from the work area. Keep children away. 24.
The most common accidents among table saw users, according to statistics, can be linked to kickback, the high-speed expulsion of material from the table that can strike the operator. Kickback can also result in operator’s hands being pulled into the blade.
Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury Contents of the Shipping Containers Table saw Right Wing Extension Splitter Guard Assembly Accessory Package Owner’s Manual Warranty Card...
Assembly Unpacking and Clean-Up Do not connect the table saw to the power source until assembly has been completed! Failure to comply may cause serious injury! • Tool: 12mm Wrench 1. Remove all contents from the shipping container. Do not discard any shipping material until satisfactorily.
Miter Gauge for Left Extension Wing Hardware: Miter Gauge Tools: Cross Point Screw Driver, Square 1. Change the angle on the miter gauge by loosening handle (E, Fig. 7) and turning the fence (F, Fig. 7) to desired angle. To move gauge beyond index stops of 45°...
Page 13
(B, Fig. 11) to rest on. This will help keep the sliding table the right height above the top of the table saw. 12. Use two jacking screws (G, Fig. 8) to raise the sliding table until it contacts the straight edge.
Sliding Table Miter Gauge Hardware: Miter Gauge, Fence, (2) Handles, Stop, Fence Bar, Indicator Bar, Bushing, Bracket Clamp Assembly & (2) Handles Tools: 2.5mm Hex Wrench 1. Slide the miter gauge fence (B, Fig. 13) into the bar (A, Fig. 13) and attach to the miter gauge body (C, Fig.
The optional wood extension table (including the optional router table) sits flush against the saw table and along the inside of the rails. The JET logo (or warning label on the router table) should face outward. The extension table is not bolted to the saw table, it is bolted only to the rails.
(Figure 17). As one part of the edge becomes level with the table, tighten the clamp on that side. Then move to the other side and repeat, until the full length of the edge is level with the saw table. Lay a straight edge across both extension table and saw table to ensure proper leveling.
slot (A. Fig. 21), orient the guide tube (B) with respect to the rail (C) as shown in Figure 21. If your left table wing is the sliding table type (D, Fig. 22), mount the guide tube (F) so it lines up with the left edge on the angle iron portion of the rail (E).
(A, Fig. 27) the same number of turns until the space between the bottom of the fence and the table is the same. Care must be taken to raise or lower the fence on each side equally or the fence may not be 90° to the table after the height adjustment is performed.
Installing the Blade When installing or changing saw blade, always disconnect saw from power source! Failure to comply may cause serious injury! Hardware: Blade Tools: Arbor Wrench, Scrap Piece of Wood 1. Raise the blade arbor and make sure the arbor is at the zero degree position.
Blade Guard Assembly Hardware: Blade Guard Assembly, Splitter Guard Assembly Tools: 12mm Wrench, 17mm Wrench or Adjustable Wrench, 3mm Hex Wrench 1. With a 3mm hex wrench, loosen two set screws (G, Fig. 34) on the splitter guard assembly and remove the bracket. 2.
A qualified electrician must complete all electrical connections! Failure to comply may result in serious injury! The JWSS-10CS table saw is rated at 1-3/4 HP, 1Ph, 115V/230V prewired 115V. To switch the JWSS-10CS from 115V to 230V: Disconnect the machine from the power source, (unplug).
Repair or replace a damaged or worn cord immediately. 115 Volt Operation Your table saw is set at the factory to run at 115- volt operation. When wired for 115 volt, this table saw is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated in (A).
XACTA Fence Cursor Adjustment This adjustment must be checked whenever a different blade is installed. 1. Disconnect the table saw from the power source. 2. Raise the saw blade above the tabletop. 3. Unlock the fence and slide it to approximately four inches from the saw blade.
Adjusting 45° and 90° Positive Stops The stops have been adjusted at the factory. After a period of use, or, after moving the saw to another location, the stops may no longer be set properly. To check and adjust the stops: Tool: 12mm Wrench, Combination 1.
Wear Adjustment in Raising Mechanism As the worm gear wears with time you may notice a little play in the handwheel. To adjust for wear in the raising mechanism: 1. Disconnect the machine from the power source, unplug. 2. Referring to Figure 48, remove the front panel (D) by unscrewing the lock knob (A), pulling off the handwheel (B) and removing five pan head screws (C) that hold the front panel.
Changing Poly V-Belt Make all machine adjustments or maintenance with the machine unplugged from the power source. Failure to comply may cause serious injury! 1. Disconnect the machine from the power source, unplug. 2. Lower the blade to its lowest point and tilt to 45°.
Maintenance General Maintenance Cabinet and Motor: Keep the inside of the cabinet clear of sawdust and wood chips. Vacuum out the inside of the cabinet and blow out the inside with an air hose. Make sure the motor fan and fan cover are also kept clear of sawdust. Worm Shafts and Trunnions: Use a wire brush and a cleaner/degreaser to clean worm shaft, and trunnions.
Troubleshooting Trouble Possible Cause Overload tripped Saw unplugged from wall or motor Fuse blown or circuit breaker tripped Saw stops or will not start Cord damaged Starting Capacitor is bad Centrifugal Switch bad or out of adjustment Stops not adjusted correctly Does not make Angle pointer not set accurately accurate 45°...