Clarion am/fm dvd video / video cd / cd / mp3 player / cd changer controller with 7" lc display owner's manual & installation manual vrx745vd (68 pages)
Thank you for purchasing the Clarion VRX630. This owner’s manual is for the VRX630. Please read this owner’s manual in its entirety before operating this equipment. After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. vices may disturb the picture or cause noise. 8mmMAX If the reception is poor, switch to a station with 286-6215-00 SERIAL No. Clarion Co.,Ltd. good reception. MADE IN CHINA QC-6710B MODEL VRX630 GROUND AM 530-1710kHz/F M 87.9-107.9MHz THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Page 4
CONTROLS / COMMANDES / REGLER / CONTROLLI REGELAARS / CONTROLES / KONTROLLER Main unit / Unité principale / Unidad principal With the Display closed / Avec l`afficheur fermé / Con el visualisador cerrado 6 7 8 With the Display open / Avec l`afficheur ouvert / Con el visualisador abierto ¥...
DVD Changer mode display COLOR LCD DISPLAY While the car is moving, the screen below is dis- played. TV mode display COLOR LCD DISPLAY VRX630 INFORMATION PANEL MAIN • No sub-indication INFORMATION PANEL MAIN...
6. DCP The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car. Removing the DCP 1.
7. REMOTE CONTROL Remote control unit Inserting the Batteries 1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow. 2. Insert the AA (SUM-3, IECR-6/1.5V) batter- ies that came with the remote control unit facing in the directions shown in the figure, then close the rear cover.
Functions of Remote Control Unit Buttons Mode Button £ FUNC Switches among Radio, CD changer, MD changer, DVD changer and TV. Turns power on and off. When pressed and held for 1 second: Turns power off. ¢ BAND Switches reception band. DISC UP ∞...
8. OPERATIONS Basic Operations CAUTION When the unit is turned on, starting and stop- ping the engine with its volume raised to the maximum level may harm your hearings. Be careful about adjusting the volume. Note: • Use this unit after starting the engine. Turning on and off the power Note: •...
Page 11
• If a title has been input, it is shown in the SUB dis- play. If no title has been input, “---------” appears in the display. To input a title, refer to the subsection “Entering titles” in “Other Functions” section. •...
Basic Operations When the panel is closed: Each time you press the Z-EHCR button 9, the tone effect changes in the following order: “Z-EHCR 1” “Z-EHCR 2” “Z-EHCR 3” “Z-EHCR OFF” “Z-EHCR 1”... When the panel is open: 1. Press the A-M button & to change into the AUDIO-MODE display.
Basic Operations Turning on/off the loudness The loudness effect emphasizes the bass and treble to create a natural sound tone. When you are listening to music at a low volume, it is rec- ommended to use the loudness effect. This function is enabled only when the panel is open.
Radio Operations 2. Press the right or left side of SEARCH button 2 to automatically seek a station. When the right side of SEARCH button 2 is pressed, the station is sought in the direction of higher frequencies; if the left side of SEARCH button 2 is pressed, the station is sought in the direction of lower frequencies.
CD Changer Operations CD changer functions When an optional CD changer is connected through the CeNET cable, this unit controls all CD changer functions. This unit can control a to- tal of 2 changers (MD and/or CD and/or DVD). Press the FNC button 1 and select the CD changer mode to start play.
CD Changer Operations Fast-forward/Fast-backward Fast-forward Press and hold the right side of the SEARCH button 2 for 1 second or longer. Fast-backward Press and hold the left side of the SEARCH but- ton 2 for 1 second or longer. Top function The top function plays from the first track (track No.
MD Changer Operations MD changer functions When an optional MD changer is connected through the CeNET cable, this unit controls all MD changer functions. This unit can control a total of 2 changers (MD and/or CD and/or DVD). Press the FNC button 1 and select the MD changer mode to start play.
Page 18
MD Changer Operations Scan play The scan play locates and plays the first 10 sec- onds of each track on a disc automatically. This function continues on the disc until it is cancelled or the mode is changed. The scan play is useful when you want to select a desired track.
DVD Changer Operation DVD changer functions When an optional DVD changer is connected through the CeNET cable. In this case, this unit only provides a part of the DVD changer functions. As for other operations not written in this manual, operates with a remote control unit provided with your DVD changer.
DVD Changer Operation DVD-Video Operation Showing the DVD menu 1. Press the TITLE button ( during playback. The DVD menus appears. The displayed contents may differ, depending on the DVD software. • Example showing menu display Using the title menu On DVD discs containing two or more titles, you can select from the title menu for playback.
Watching a video CD Showing the V-CD menu (for V-CD discs with Play Back Control) This key does not function on some discs. 1. Press the TITLE button ( during playback. The V-CD menu appears. The displayed contents may differ, depending on the V-CD software.
Page 22
DVD Changer Operation Fast forward and fast backward 1. Press and hold the right or left side of the SEARCH button 2 during playback. Press and hold the button, and the playback speed becomes 4-time faster first and then 8-time faster 3 seconds later. Release the button, and the normal speed is restored.
DVD Changer Operation Track random playback This operation plays the file in the folder in ran- dom order. 1. Press the RDM button 8. 2. Press the RDM button 8 again and random playback is turned off. Folder random playback This operation plays back tracks recorded on the disc in no particular order.
TV Operations Seek tuning 1. Press the BND button % and select the de- sired TV band (TV1 or TV2). If “MANU” is lit in the display (or when the panel is closed, if the indicator “SRCH” is not lit), press and hold the BND button % for 1 second or longer.
Page 25
Setting the TV diver This function is enabled only when the panel is open. Normally use the TV diver with the “ON” position. You can change the reception setting for the TV antenna connected to the TV tuner. 1. Press the ADJ button * to switch to the ad- justment selection display.
CCD Camera Monitoring the CCD camera The CCD camera can be connected to this unit. For the power supply of the camera, mount the power box sold separately (CCA-188). Notes: • This function is not available when the display is stored.
Other Functions Always turning on the button illumination on the operation panel Note: • The following operation is enabled when the panel is open. The button illumination on the operation panel when the display is turned upward, can be switched between “ON” and “OFF”. “ON”: Button illumination on the operation panel turns on for 5 seconds;...
This function is not compatible wiht all cellular telepones Contact your local authorized Clarion dealer for information on proper instal- lation and compatibility. VRX630 DSP operations DSP control function...
Page 29
Auto loudness adjustment Operate the JOYSTICK ¡ upward or downward to adjust an auto loudness level (0 to 10). Woofer out adjustment Select woofer output out of “STEREO”, “MONO”, or “OFF”. Operate the JOYSTICK ¡ upward or downward to select a desired item, and then press the ENT at the center of the JOYSTICK ¡...
Page 30
DSP operations 4. Operate the JOYSTICK ¡ rightward or left- ward to select “BALANCE” or “FADER”. 5. Operate the JOYSTICK ¡ upward or down- ward to make an adjustment. 6. Operate the JOYSTICK ¡ rightward or left- ward to move the cursor to “MENU”, and press the ENT at the center of the JOY- STICK ¡...
Page 31
6. Operate the JOYSTICK ¡ rightward or left- ward in the BASIC/USER pattern selection/ memory display to select USER memory P1 to P6 to be stored, and press the ENT at the center of the JOYSTICK ¡ for 2 seconds or longer to store the adjusted G.EQ pattern to the USER memory.
Page 32
DSP operations Note: • If the VSE effect is set to OFF, the adjustment made in “VSE operations” is not reflected in the music source. Calling VSE BASIC Pattern/USER Pattern 1. Press the A-M button & to show the AUDIO- MODE display.
Page 33
3. Operate the JOYSTICK ¡ rightward or left- ward to select “ON” or “OFF” and press the ENT at the center of the JOYSTICK ¡ to set it. Note: • If the P.EQ effect is set to OFF, the adjustment made in “P.EQ operations”...
9. IN CASE OF DIFFICULTY Problem Power does not Fuse is blown. turn on. (No sound is produced.) Incorrect wiring. Nothing happens The microprocessor has when buttons are malfunctioned due to noise, pressed. etc. Display is not accurate. DCP or main unit connectors are dirty.
Page 35
Problem Cause When the TV Bad receiving condition tuner is con- nected, the image gets unclear. The TV tuner has Bad receiving condition a double or triple image. The TV tuner has Presence of jamming spots or stripes in the image. There are red, green, and blue points in the...
10. ERROR DISPLAYS If an error occurs, one of the following displays is displayed. Take the measures described to eliminate the problem. Error Display ERROR 2 A CD inside the CD changer is not loaded. ERROR 3 A CD inside the CD changer cannot be played due to scratches, etc.
11. SPECIFICATIONS FM Tuner Frequency Range: 87.9 MHz to 107.9 MHz Usable Sensitivity: 11 dBf 50dB Quieting Sensitivity: 17 dBf Alternate Channel Selecitivity: 75 dB Stereo Separation(1 kHz): 35 dB Frequency Response(+/-3 dB): 30 Hz to 15 kHz AM Tuner Frequency Range: 530 kHz to 1710 kHz Usable Sensitivity: 25 V Audio Amplifier...