Advertisement
Quick Links
CLEI: BVL3AEKD_ _
Product P/N: 1442351G1
D
ESCRIPTION
The Small Form‐Factor Pluggable Gigabit Ethernet 1510 nm
CWDM (SFP) is a single‐mode fiber SFP that plugs into ADTRAN
Gigabit Ethernet modules designed to accept SFPs. The SFP
provides a dual optical interface to a Gigabit Ethernet physical
interface.
Installed into an appropriate module, the SFP provides a Gigabit
Ethernet interface to the supporting system.
This SFP is designed for use in Coarse Wavelength Division
Multiplexing (CWDM) applications.
The following features are supported on the SFP:
♦
LC optical connectors
♦
Transmit Wavelength: 1511 nm (1504.5 nm ‐ 1517.5 nm)
♦
Receive Wavelength: 1200 nm ‐ 1625 nm
♦
Optical distance: 50 km maximum
Small Form-Factor Pluggable Gigabit
Ethernet 1510 nm CWDM
S
PECIFICATIONS
Specifications for the SFP are as follows:
♦
Optical Specifications:
◊
Optical transmit level: 0 dBm to –5 dBm
◊
Optical receive level: –3 dBm to –24 dBm
♦
Extended Environmental Support:
◊
Operational temperature range: –40°C to +85°C
◊
Storage temperature range: –40°C to +85°C
◊
Relative humidity to 95%, noncondensing
I
NSTALLATION
To install the SFP into an appropriate module, complete the
following steps:
1. Inspect the SFP. If damaged, file a claim with the carrier and
then contact ADTRAN Customer Support.
!
CAUTION
Do not remove the protective end cap from the SFP until the fiber
optic cable is ready to be connected.
2. Insert the SFP into the SFP cage on the module. Ensure the
manufacturer's label on the SFP is facing upward for correct
installation.
3. Slide the SFP all the way into the receptacle until there is an
audible "click".
NOTE
The latch on the SFP is used to remove the SFP from the cage on
the circuit card.
jobAid
Issue Date: July 2010
Document P/N: 61442351G1-22B
Advertisement
Related Manuals for ADTRAN jobAid 1442351G1
Summary of Contents for ADTRAN jobAid 1442351G1
- Page 1 ♦ Optical Specifications: ◊ Optical transmit level: 0 dBm to –5 dBm ◊ Optical receive level: –3 dBm to –24 dBm ♦ Extended Environmental Support: ◊ Operational temperature range: –40°C to +85°C ◊ Storage temperature range: –40°C to +85°C ◊ Relative humidity to 95%, noncondensing NSTALLATION To install the SFP into an appropriate module, complete the following steps: 1. Inspect the SFP. If damaged, file a claim with the carrier and then contact ADTRAN Customer Support. ESCRIPTION CAUTION Do not remove the protective end cap from the SFP until the fiber The Small Form‐Factor Pluggable Gigabit Ethernet 1510 nm optic cable is ready to be connected. CWDM (SFP) is a single‐mode fiber SFP that plugs into ADTRAN Gigabit Ethernet modules designed to accept SFPs. The SFP provides a dual optical interface to a Gigabit Ethernet physical 2. Insert the SFP into the SFP cage on the module. Ensure the interface. manufacturer’s label on the SFP is facing upward for correct installation. Installed into an appropriate module, the SFP provides a Gigabit Ethernet interface to the supporting system. 3. Slide the SFP all the way into the receptacle until there is an audible “click”. This SFP is designed for use in Coarse Wavelength Division Multiplexing (CWDM) applications.
- Page 2 The ADTRAN system chassis frame ground terminal must be connected to a reliable earth ground to ensure that the metal enclosure of the SFP is properly grounded via the backplane connector. Warranty: ADTRAN will replace or repair this product within the warranty period if it does not ADTRAN CUSTOMER CARE: meet its published specifications or fails while in service. Warranty information can From within the U.S. 1.800.726.8663 be found online at www.adtran.com/warranty.