Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel DD24DTX6PX1
Summary of Contents for Fisher & Paykel DD24DTX6PX1
- Page 1 DOUBLE DISHDRAWER™ DISHWASHER CONTEMPORARY DD24DTX6PX1 INSTALLATION GUIDE US CA...
-
Page 3: Safety And Warnings
SAFETY AND WARNINGS WARNING! WARNING! Electric Shock Hazard Cut Hazard Failure to follow this advice may result in Failure to use caution could result in injury. electrical shock or death. • Take care – panel edges are sharp. • This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce WARNING! the risk of electric shock by providing a path of... - Page 4 SAFETY AND WARNINGS WARNING! To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance. Servicing Do not repair or replace any part of the appliance unless specifically recommended in this guide.
-
Page 5: Tools And Components
TOOLS AND COMPONENTS PARTS SUPPLIED TOOLS REQUIRED Keep all packing materials until the unit has been inspected. Not supplied Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &... -
Page 6: Product Dimensions
PRODUCT DIMENSIONS PRODUCT DIMENSIONS INCHES A Overall height* 34 – 36 3/8 864 – 924 B Overall width 23 9/16 C Overall depth 22 9/16 D Height of chassis 22 9/16 E Depth of chassis 21 3/4 F Height of upper door panel 17 3/8 G Height of lower door panel 12 5/16 H Depth of door panel... - Page 7 CABINETRY DIMENSIONS CLEARANCES Connections can be located in an adjacent cabinet on either side of the DishDrawer™ Dishwasher*** PLAN ISOMETRIC CABINETRY DIMENSIONS INCHES CABINETRY CLEARANCES INCHES A Minimum inside height* A Minimum clearance to adjacent cupboard door 1/16 B Inside width 23 5/8 B Minimum clearance to corner cupboard C Minimum inside depth**...
- Page 8 PLUMBING & ELECTRICAL CONSIDERATIONS Hose and cord lengths Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Preparation’ for service access requirements. If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher &...
- Page 9 HARD-WIRING (OPTIONAL) You have the option to hard-wire your DishDrawer™ Dishwasher. To do this, we recommend to remove the supplied power cord and do the hardwiring installation as close to the cavity as possible. Lift the cover upwards until you are able to pull out towards you to remove.
- Page 10 HARD WIRING (OPTIONAL) Fix the Live and Neutral wires to the terminal block and the Earth wire to Ensure the hoses are not twisted before the chassis. refitting the drawer to the runners and clipping into place via both locking tabs. rear L rib hook...
-
Page 11: Service Access
PREPARATION SERVICE ACCESS MOISTURE PROTECTION We recommend locating the service holes on either side of the DishDrawer™ Dishwasher as shown below. If the holes are created through wood, ensure the edges are smooth and rounded If the holes are created through metal, ensure the supplied edge protector is fitted. Align the supplied moisture protection Ensure power cord is routed through a separate service hole to the hoses. - Page 12 SECURE TO CABINETRY VIA BRACKETS (METHOD A) Secure all four side brackets to the DishDrawer™ Dishwasher, aligning Partially open one of the drawers and bracket A with slot A and bracket B remove the first screw cover from the with slot B. trim moulding.
- Page 13 SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B) Using the supplied hex socket and a screwdriver, level the DishDrawer™ Dishwasher as required. Rotate clockwise to increase the height of each leg Optionally, fit the two top brackets. and anticlockwise. Ensure the ends of the brackets are not It can help to reduce the loading on the pushed into the chassis.
-
Page 14: Install Toe Kick
INSTALL TOE KICK Snap off excess toe kick material and both end tabs. Measure toe kick height against the Smooth the edges. base of the lower tub. Slide toe kick onto the mounting rails and secure. Ensure a 12mm clearance is maintained between the floor and Carefully score toe kick at the toe kick, the end tabs can be used... - Page 15 PLUMBING & ELECTRICAL CONNECTION Ø38MM STANDPIPE INSTALLATION SINK TRAP/WASTE TEE INSTALLATION Install the drain hose support to the Install the drain hose support to the back wall, as close to the underside of back wall, as close to the underside of the countertop as possible.
- Page 16 PLUMBING & ELECTRICAL CONNECTION AIR GAP INSTALLATION Connect the inlet hose to tap and hand- tighten into place. Install your Air Gap Kit to the benchtop. Using a spanner or pliers, turn a further We recommend using a Dual Air Gap Kit. 180°...
-
Page 17: Installer Checklist
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Electrical … Ensure all electrical tests have been conducted in accordance with local regulations. Installation … Check all parts are installed correctly and are secure. Test operation … Ensure all clearance gaps have been maintained. …... -
Page 18: Troubleshooting
TROUBLESHOOTING No program indicator lights up when the drawer is opened DISPLAY POSSIBLE CAUSE WHAT TO DO Ensure power is connected and is switched on. Water 1 Ensure the water supply is turned on. may need to be activated. Refer to your user guide for details. AUTO POWER-ON Supply fault. - Page 19 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.