SAFETY AND WARNINGS WARNING! WARNING! Electrical Shock Hazard Tipping Hazard Failure to follow this advice may result Failure to do so can result in death or serious in electric shock or death. burns to children of adults. • Before carrying out any work on the •...
SAFETY AND WARNINGS WARNING! GENERAL INSTALLATION INFORMATION To avoid hazard, follow these instructions carefully before installing or using Cleaning and servicing this appliance. Service should only be performed by an authorised technician. Always disconnect the appliance from mains power supply before carrying out any Please make this information available to the person installing the appliance — ...
PARTS SUPPLIED FOR INSTALLATION Anti-tip bracket and lock pin (1) Screws and plastic sleeve anchors (2) TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE) IMPORTANT! THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer or the service agent.
MODEL IDENTIFICATION Model features may vary. OR90 Induction models OR90SCI1 OR90SCI4 OR90SCI6 OR90SDI6 OR90SPI6X1 PRIOR TO INSTALLATION Unpacking and handling Inspect the cooker to verify that there is no shipping damage. If any damage is detected, call the shipper and initiate a damage claim. Fisher & Paykel is not responsible for shipping damage. DO NOT discard any packing material until the cooker has been inspected.
PRODUCT DIMENSIONS Model features may vary. Optional kickstrip available (purchased separately). FRONT PROFILE OR90 PRODUCT DIMENSIONS min 898 1 Overall height of cooker (from floor to top of cooktop, excl. optional backguard) max 946 2 Overall width of cooker 3 Overall depth of cooker (from front of cooker to rear of island trim/backguard, excl. handles and dials) 4 Height of optional backguard from top of cooktop (supplied with some models only) 5 Height of chassis (excl.
CLEARANCE DIMENSIONS Cooking surface Electrical & Gas (see diagrams following) FRONT Note: OR90 The cabinetry surrounding the cooker must be heat CLEARANCE DIMENSIONS resistant and capable of withstanding temperatures of 75°C above room temperature. A Minimum vertical distance between benchtop and cabinet extending above counter Do not install the cooker near flammable materials such as curtains.
Page 9
FITTING THE OPTIONAL BACKGUARD LOCATION OF ELECTRICAL SUPPLY Backguard (supplied with some models only) Remove the screws and spacers on the rear of the cooktop. Assemble the backguard as shown and fix onto the back of the cooker using the same screws and spacers. Fix the backguard onto the cooker using the screws provided.
VENTILATION REQUIREMENTS A suitable ventilation hood may be installed above the cooker. Fisher & Paykel has a choice of ventilation hoods designed to match the rest of our kitchen appliance family. See fisherpaykel.com or your local dealer for more details. IMPORTANT Consult local building codes and/or local agencies, before starting, to ensure that hood and duct installation will meet local requirements.
Page 11
INSTALLING FOOT COVERS (OR90 MODELS) SIMPLIFIED INSTALLING FOOT COVERS (OR90 MODELS) SIMPLIFIED FITTING THE ADJUSTABLE FEET INSTALLING FOOT COVERS (OR90 MODELS) SIMPLIFIED Tip range onto its back and fix INSTALLING FOOT COVERS (OR90 MODELS) SIMPLIFIED Fitting the adjustable feet Fitting the adjustable feet covers (optional) brackets to mounting holes.
MOVING THE COOKER IMPORTANT! When raising cooker to upright position always ensure two people carry out this manoeuvre to prevent damage to the adjustable feet. BE CAREFUL: do not lift the cooker by the oven door handle, the hob rail or by lifting the cooktop trim as this may damage the appliance. When moving cooker to its final position DO NOT DRAG.
INSTALLING THE ANTI-TIP BRACKET IMPORTANT! To restrain the cooker and prevent it tipping accidentally secure the cooker to the wall using the supplied anti-tip bracket. Ensure you also fit the supplied lock pin to the anti-tip bracket. If installing the cooker above a plinth (without fitting the adjustable feet) revise the installation dimensions for the anti-tip bracket accordingly, considering that the feet have the following measurements: min 85mm – max 133mm.
Page 14
INSTALLING THE ANTI-TIP BRACKET Fitting the lock pin (models with a storage/warming drawer) Fitting the lock pin (models with a storage compartment) The anti-tip bracket is accessible by removing the storage/warmer drawer, The anti-tip bracket is accessible by opening the storage compartment door, and is positioned on the rear right side of the cooker.
ELECTRICAL CONNECTION IMPORTANT! This cooker must be connected to the mains power supply only by a suitably qualified person. This cooker must be earthed. If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the electrical system is suitable for the electricity drawn by the cooker.
Page 16
ELECTRICAL FEEDER CABLE CONNECTION IMPORTANT! SINGLE-PHASE CONNECTION The power supply cable must be connected by a Fisher & Paykel trained and support service technician or qualified person. Feeder cable section Use a type of cable according to the applicable local regulations. 1 Remove the screws that hold the cover in place at the back of the cooker.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL OPERATION Placement of unit. All internal packing materials removed. Check inside the oven. Specified clearance maintained to cabinet surfaces. Dials turn correctly and freely. Unit Level — front to back, side to side. Oven and cooktop displays are functioning correctly and oven and cooking zones can be turned on.