Related Manuals for Horizon Fitness Standard QC-S300
Summary of Contents for Horizon Fitness Standard QC-S300
- Page 1 Standard QC S300/S30 Collator Install Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 3 Table Top Collator QC-S300/S30 COLLATOR COLLATOR Important Information • This manual is designed to help you to install the QC-S300/QC-S30 Table Top Collator. Please read and understand this manual, and keep it in a safe and convenient place. • Do not operate the QC-S300/QC-S30 until you have read and understood the instructions in this manual.
-
Page 4: Safety Precautions
Safety Precautions Safety precautions are indicated in this manual as follows: The term WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. The term CAUTION indicates a potentially hazardous situation which, if not avoided, may result in serious injury, or damage to the machine. -
Page 5: Cautions For Installation
Operating Safety Precautions Warning for Installation Do not give many loads on one electrical outlet. This can cause a fire or an electrical shock. Cautions for Installation Do not install QC-S300/QC-S30 in a location where it will be exposed to direct sunlight, high tem- perature or humidity. - Page 6 This page is intentionally left blank.
- Page 7 Installation Instructions for Service Engineer This page includes installation instructions for the machine. These instructions should only be used by trained service technicians......2 How to Install a Single QC-S300/QC-S30 Collator Stand-Alone Unit: QC-S300/QC-S30 Installation Space in mm (inches): 960 (37.8”) x 1,630 (64.2”) x 1,030 (40.5”) Stand-Alone Unit + MT-100: QC-S300/QC-S30 + MT-100 Installation Space in mm (inches): 994 (39.2”) x 1,602 (63.1”) x 1,030 (40.5”) ....
- Page 8 How to Install a Single QC-S300/QC-S30 Collator * Choose a stable table which can support at least 73 Installing a Single QC-S300/QC-S30 Collator kg (160.6 lb) to install QC-S300/QC-S30. mm(inch) 1,030 (40.5") CAUTION 363 (14.3") • Do not install the QC-S300/QC-S30 on an unstable floor.
- Page 9 How to Install a Single QC-S300/QC-S30 Collator Attach the bin shelves, beginning from the bottom, by following the steps below. (1) On the drive side of each bin shelf, an arm fits under a pin inside the machine. A pin on the bin shelf fits into a notch in the frame of the machine.
- Page 10 How to Install Multiple QC-S300F/QC-S30F Collators Accessory Check (QC-S300F/QC-S30F) Upper Conveyor 1 pc Middle Conveyor 1 pc Lower Conveyor 1 pc 21101 21101 20101C1 20101A1 21101 20101B1 Gear (M092610) Solenoid Connector 1 pc Support Guide (l154294) 1 pc Clevis Pin 1 pc each 21101 20101F1...
- Page 11 How to Install Multiple QC-S300F/QC-S30F Collators Installing a QC-S300F/QC-S30F Extension Module Additional Collators: QC-S300F/QC-S30F Optional Table: MT-100 WARNING * If you are installing QC-S300F/QC-S30F on any • Do not install the QC-S300F/QC-S30 on an table except the MT-100, choose a stable table unstable floor.
- Page 12 How to Install Multiple QC-S300F/QC-S30F Collators Install the conveyors on the QC-S300F/ Rear Cover QC-S30F. Preparation for Multiple QC-S300F/ QC-S30F Collators (1) Remove the rear cover from the unit. 21101 20101M1 (2) Remove the three screws and the gear cover. Gear Cover 21101 20101N1...
- Page 13 How to Install Multiple QC-S300F/QC-S30F Collators (2) Insert the end of the drive shaft on middle con- veyor into a hole on the rear frame. Drive Shaft 21101 20101R1 (3) Insert the end of shaft into a cutout in the front frame.
- Page 14 How to Install Multiple QC-S300F/QC-S30F Collators Attach the upper conveyor to the middle Upper conveyor. Conveyor Middle Conveyor (1) Insert the four pins on the upper conveyor into the U-shaped cutouts on the middle conveyor. U-shaped Cutout 21101 20101W1 Connecting the QC-S300/QC-S30 and the Rear Cover QC-S300F/QC-S30F (1) Attach the rear cover on the QC-S300F/QC-S30F...
- Page 15 How to Install Multiple QC-S300F/QC-S30F Collators (6) Connect the two MT-100 tables using the connect- ing plate. Set the connecting plate between the tables and attach it using four screws. Connecting Plate 21101 20102B1 Support Guide (7) Insert the bridge between the lower conveyor and the lower left cover, and push it down into posi- tion.
- Page 16 How to Install Multiple QC-S300F/QC-S30F Collators (4) Attach solenoid connector B to the connector on the conveyor. Connector B Connector C (5) Attach solenoid connector C to the left connector on the QC-S300/QC-S30. (6) Insert connector cables into the duct of the middle conveyor.
- Page 17 How to Install Multiple QC-S300F/QC-S30F Collators Plug the power cord into the QC-S30F. Power Cord Plug the power cord into an outlet. Important • Plug the power cord into a properly-grounded outlet. • If you must use an ungrounded outlet, be sure to 21101 20102K1 ground the machine separately.
- Page 18 This page is intentionally left blank.