Table of Contents
Advertisement
Quick Links
QFX10008 Switch Quick Start Guide
January 2014
Part Number: 530-068237
Revision 01
Contents
Copyright © 2016, Juniper Networks, Inc.
This document describes how to install the Juniper Networks
Quick Start Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Step 1-Preparing the Site for the QFX10008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rack-Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Clearance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Cooling and Airflow Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Step 2-Unpacking the QFX10008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 3-Mounting the Switch Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting the QFX10008 Using a Mechanical Lift . . . . . . . . . . . . . . . . . . . . . . . 8
Manually Mounting a QFX10008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Step 4-Installing Line Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Step 5-Installing the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Step 6-Connecting Power to the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Ground the Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Install AC Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Install DC Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Step 7-Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Step 8-Performing Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Safety Warnings Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Power Cable Warning (Japanese) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
®
QFX10008 Switch Chassis.
1
Advertisement
Table of Contents
Related Manuals for Juniper QFX10008
Summary of Contents for Juniper QFX10008
-
Page 1: Table Of Contents
Manually Mounting a QFX10008 ........ -
Page 2: Quick Start Description
QFX10008 switch in a standard 19 in. (483 mm) equipment rack by using the supplied rack-mounting kit and the front-mounting bracket that is attached to the chassis. Before you install the QFX10008, make sure the site meets all of the power, cooling, and clearance requirements. See the site preparation guidelines and power requirements in... -
Page 3: Clearance Requirements
Figure 1: Clearance Requirements for Airflow and Hardware Maintenance for a QFX10008 If you are mounting a QFX10008 in a rack with other equipment, ensure that the exhaust from other equipment does not blow into the intake vents of the chassis. -
Page 4: Step 2-Unpacking The Qfx10008
Leave at least 24 in. (61 cm) both in front of and behind the QFX10008 for service personnel to remove and install hardware components. To be NEBS GR-63 compliant, allow at least 30 in. - Page 5 Remove the plastic cover from the switch chassis. Use a 13/32 in. (10 mm) open-end or socket wrench to remove the four sets of bracket bolts that secure the chassis to the shipping pallet (see Figure 4 on page Copyright © 2016, Juniper Networks, Inc.
-
Page 6: Step 3-Mounting The Switch Chassis
Save the shipping box and packing materials in case you need to move or ship the switch at a later time. Step 3–Mounting the Switch Chassis To install the QFX10008, first install the mounting hardware and then perform one of these two procedures: Installing the Mounting Hardware on page 6... - Page 7 Connect left front and rear brackets (see Figure 5 on page Insert six of the screws provided with the mounting brackets into the overlapping bracket holes. Hand-tighten the screws fully (to 12–16 in.-lb torque) using a number 2 Phillips screwdriver. Copyright © 2016, Juniper Networks, Inc.
-
Page 8: Mounting The Qfx10008 Using A Mechanical Lift
Hand-tighten the screws fully (to 12–16 in.-lb torque) using a number 2 Phillips screwdriver. Mounting the QFX10008 Using a Mechanical Lift Because of the switch's size and weight, we strongly recommend using a mechanical lift to install the QFX10008. - Page 9 Mounting the QFX10008 Using a Mechanical Lift CAUTION: Before front-mounting the switch on a rack or cabinet, have a qualified technician verify that the rack or cabinet is strong enough to support the switch's weight and is adequately supported at the installation site.
- Page 10 QFX10008 Switch Quick Start Guide Figure 6: Loading the QFX10008 into a Rack Using a Mechanical Lift Using the lift, align the switch in front of the rack, centering it in front of the mounting brackets. Lift the chassis approximately 0.75 in. (1.9 cm) above the surface of the mounting brackets.
-
Page 11: Manually Mounting A Qfx10008
Do not lift the chassis by the handles. CAUTION: Before front-mounting the switch in a rack, have a qualified technician verify that the rack is strong enough to support the switch's weight and is adequately supported at the installation site. Copyright © 2016, Juniper Networks, Inc. - Page 12 QFX10008 Switch Quick Start Guide Before you install the switch, remove all components except the two fan tray controllers from the chassis. For details on how to remove switch components, such as control boards, fan trays, power supplies, and SIBs, see QFX10008 Switch Hardware Guide http://www.juniper.net/techpubs/...
- Page 13 Manually Mounting a QFX10008 Figure 8: Lifting the QFX10008 Without Using a Mechanical Lift Carefully slide the switch onto the mounting brackets until the front-mounting brackets attached to the chassis contact the rack rails. The mounting brackets ensure that the holes in the front-mounting brackets attached to the chassis align with the holes in the rack rails.
-
Page 14: Step 4-Installing Line Cards
QFX10008 Switch Quick Start Guide Figure 9: Installing a QFX10008 in a 4-Post Rack After you install the mounting screws and securely bolt the chassis to the rack, reinstall the components in the chassis. For information on how to install switch components, QFX10008 Switch Hardware Guide http://www.juniper.net/techpubs/... - Page 15 Lifting the line card by the handles or edge connectors might bend them, which would prevent the line cards from being properly seated in the chassis. See Figure 12 on page Copyright © 2016, Juniper Networks, Inc.
- Page 16 QFX10008 Switch Quick Start Guide Figure 12: Line Card Connectors 1— Connectors Remove the line card from the electrostatic bag and inspect it for any damage before installing it into the chassis. Grasp and lift the line card by the sides.
-
Page 17: Step 5-Installing The Front Panel
Step 5–Installing the Front Panel Step 5–Installing the Front Panel The front panel is required on the QFX10008 to protect fiber optic cabling and to provide additional protection from electromagnetic interference (EMI). The front panel can be installed with or without the optional cable management system. - Page 18 QFX10008 Switch Quick Start Guide Use the Phillips screwdriver to attach two mounting screws to the latch bracket at the top left of the chassis frame (see Figure 15 on page 18). Figure 15: Attaching Front Panel Brackets Use the final two mounting screws to attach a latch bracket to the top right of the chassis frame so there are brackets on all four corners of the front of the chassis.
-
Page 19: Step 6-Connecting Power To The Chassis
Ground the Chassis To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, you must connect the QFX10008 to earth ground before you connect it to power. For installations that require a separate grounding conductor to the chassis, you must attach a protective earthing terminal bracket on the QFX10008. - Page 20 6 AWG (13.3 mm²), minimum 90° C wire, or as permitted by the local code. Grounding lug for your grounding cable (provided)—This bracket attaches to the lower left corner of the QFX10008 switch chassis next to PSU 5, providing a protective earthing terminal for the switch. The grounding lug required is a Panduit LCD6-10A-L or equivalent.
-
Page 21: Install Ac Power Supplies
Install AC Power Supplies QFX10008 power supplies are hot-insertable and are field-replaceable units (FRUs). You can install up to six power supplies in a QFX10008. The power supplies install in the rear of the chassis in the slots provided along the left side. - Page 22 QFX10008 Switch Quick Start Guide Figure 19: Removing the PSU Cover Panel Taking care not to touch power supply connections, remove the power supply from its bag. Peel back and remove the protective plastic wrap that covers all four sides of the power supply.
- Page 23 Install AC Power Supplies Figure 20: Installing a QFX10008 AC Power Supply Locate two power cords shipped with the switch; the cords have plugs appropriate for your geographical location. Attach each power cord to a dedicated AC power source outlet.
-
Page 24: Install Dc Power Supplies
Install DC Power Supplies QFX10008 power supplies are hot-insertable and are field-replaceable units (FRUs). You can install up to six power supplies in a QFX10008. The power supplies install in the rear of the chassis in the slots provided along the left side. - Page 25 Electrostatic discharge (ESD) grounding strap DC power source cables (not provided) with the cable lugs (provided) attached The provided terminal lugs in a QFX10008 are sized for 4 AWG (21.1 mm ) power source cables. The DC power source cables that you provide must be 4 AWG (21.1 mm...
- Page 26 QFX10008 Switch Quick Start Guide Remove the nuts from each DC power input terminal, using the 13/32 in. (10 mm) nut driver or socket wrench to loosen the nuts. Ensure that the power source circuit breaker is open so that the voltage across the DC power source cable leads is 0 V and that the cable leads do not become active while you are connecting DC power.
- Page 27 Install DC Power Supplies Figure 22: Connecting the DC Power Supply Cables to a QFX10008 Install the plastic cable cover over each set of power cables by using the Phillips (+) screwdriver, number 2, to tighten the screw. If the power supply slot on the chassis has a cover panel on it, insert your thumb and forefinger into the finger holes, squeeze, and pull the cover out of the slot.
- Page 28 QFX10008 Switch Quick Start Guide Figure 23: Removing the PSU Cover Panel Unscrew the captive screw in the counterclockwise direction by using the Phillips (+) screwdriver, number 1. Pull the captive screw away from the faceplate of the power supply to release the latch.
- Page 29 Install DC Power Supplies Figure 24: Installing a QFX10008 DC Power Supply 1— Source input 1 enable switch 2— Source input 2 enable switch WARNING: Ensure that the power cords do not block access to switch components or drape where people can trip on them.
-
Page 30: Step 7-Connecting To The Network
) position. Step 7–Connecting to the Network You can configure and manage the QFX10008 by using a dedicated console. Every control board has a console port with an RJ-45 connector. Use the console port to connect the device to the management console or to a console server. The console port accepts a cable with an RJ-45 connector. -
Page 31: Step 8-Performing Initial Configuration
Figure 27: Connecting a Switch Directly to a Management Console Step 8–Performing Initial Configuration You must perform the initial configuration of a QFX10008 switch through the console port using the command-line interface (CLI). Before you begin connecting and configuring the switch, set the following parameter values on the console server or PC: Baud Rate—9600... - Page 32 QFX10008 Switch Quick Start Guide Add a password to the root administration user account. [edit] root@# set system root-authentication plain-text-password New password: password Retype new password: password (Optional) Configure the name of the switch. If the name includes spaces, enclose the name in quotation marks (“...
-
Page 33: Safety Warnings Summary
A base AC configuration is 280 lb (127 kg) and redundant AC configurations can weigh 322 lb (146.06 kg). Installing the QFX10008 switch in a rack or cabinet requires either a mechanical lift or three people to lift the switch and another person to secure it to the rack. -
Page 34: Power Cable Warning (Japanese)
QFX10008 Switch Quick Start Guide Power Cable Warning (Japanese) The attached power cable is only for this product. Do not use this cable for another product. Contacting Juniper Networks For technical support, see http://www.juniper.net/support/requesting-support.html Copyright © 2016, Juniper Networks, Inc.