Resetting The Remote Memory; Reassigning Device Control Selectors; Transport Control Punch-Through - Harman Kardon AVR 525 Owner's Manual

the device selected by the AVR 525 or the remote.
To program the remote for Channel Control Punch-
Through, follow these steps:
1. Press the Input Selector Button
you wish to have the channel control associated with
and the Mute Button 43 at the same time until
the red light appears under the Input Selector
and the Program/ SPL Indicator
amber.
2. Press the Volume Down Button 40
Program/SPL Indicator will stop flashing
and stay amber.
3. Press and release the Input Selector Button
for the device that will be used to change the chan-
nels. The Program/SPL Indicator
green three times and then go out to confirm the
data entry.
Example: To control the channels using your cable
box or satellite receiver while the remote is set to
control the VCR, first press the VID 1/VCR Input
Selector Button and the Mute Button
at the same time. Next, release them and press the
40
Volume Down Button , followed by the VID
2/TV Input Selector Button .
NOTE: To remove the Channel Control Punch-Through
and return the remote to its original configuration, repeat
the steps shown in the example above. However, press
the VID 1/VCR Input Selector in Steps 1 and 3.

Transport Control Punch-Through

The AVR 525's remote may be programmed to operate
so that the Transport Control Functions
Stop, Fast Forward, Rewind, Pause and Record) for a
VCR, DVD or CD will operate in conjunction with one of
the other devices controlled by the remote. For exam-
ple, while using and controlling the TV, you may wish to
start or stop your VCR or DVD without having to change
the device selected by the AVR 525 or the remote. To
program the remote for Transport Control Punch-
Through, follow these steps:
1. Press the Input Selector for the device you
wish to have the channel control associ-ated with
and the Mute Button 43 at the same time until
the red light appears under the Input Selector
and the Program/ SPL Indicator
amber.
2. Press the Play Button . The Program/ SPL
Indicator will stop flashing and stay amber.
3. Press and release the Input Selector Button
for the device that will be used to change the chan-
nels. The Program/SPL Indicator
green three times and then go out to confirm the
data entry.
Example: To control the transport of a DVD player
for the device while the remote is set to control the TV, first press
the VID 2/TV Input Selector Button
Mute Button 43
them and press the Play Button
flashes the DVD Input Selector Button
NOTES:
. The To remove the Channel Control Punch-Through and
•
return the remote to its original configuration, repeat
the steps in the example above. However, press the
VID 2/TV Input Selector
Before programming the remote for Volume, Channel
•
will blink or Transport Punch-Through, make certain that any
programming needed for the specific TV, CD, DVD,
cable or satellite receivers has been completed.

Reassigning Device Control Selectors

Although each Input Selector
assigned to the category of product shown on the
43
remote, it is possible to reassign one of these buttons to
operate a second device of another type. For example, if
you have two VCRs but no satellite receiver, you may
program the "SAT" button to operate a second VCR.
Before following the normal programming steps for
either Three-Digit entry or Auto Search code entry, you
must first reassign the button with the following steps:
1. Press the Input Selector
and the Mute Button
the red light appears under the Input Selector
and the Program/ SPL Indicator
(Play,
amber.
2. Press the Input Selector
wish to program into the reassigned
button.
3. Enter the three-digit code for the specific model
you wish the reassigned button to operate.
4. Press the same Input Selector
Step 1 once again to store the selection. The red
LED under the re-assigned Input Selector will flash
three times and then go out.
Example: To use the CBL/SAT button to operate a
flashes
second VCR, first press the CBL/SAT Input
Selector and the Mute Button
same time until the red light glows under the
CBL/SAT button. Press the VCR
followed by the three-digit code for the specific
model you wish to control. Finally, press the
CBL/SAT Button
will blink

Resetting the Remote Memory

As you add components to your home-theater system,
occasionally you may wish to totally reprogram the
remote control without the confusion of any commands,
and the
macros or "Punch-Through" programming that you may
at the same time. Next, release
have done. To do this, it is possible to reset the remote
, followed by
to the original factory defaults and command codes by
.
following these steps. However once the remote is
reset, all commands or codes that you have entered will
be erased and will need to be re-entered:
1. Press any of the Input Selector Buttons
in Steps 1 and 3.
2. Press the "3" Button
3. The red LED under the Input Selector
4. The Program/SPL Indicator
is normally
5. When the Program/SPL Indicator
you wish to reassign
43
at the same time until
flashes
for the device you
pressed in
43
at the
Button,
again.
the "O" Button at the same time until the
Program/SPL Indicator begins to flash amber.
three times.
out and the Program/SPL Indicator
flashing and turn green.
will remain green
until the remote is reset. Note that this may take a
while, depending on how many commands are in the
memory and need to be erased.
the remote has been reset to the factory settings.
and
will go
will stop
goes out,