Page 2
English 中文 T9800 FC BUS FC BUS NTC OCC NTC OCC Cool/ Heat COOL HEAT FC BUS FC BUS NTC OCC NTC OCC Cool/ TiO2 Heat FC BUS FC BUS NTC OCC NTC OCC Cool/ FLOOR Heat HEAT FC BUS NTC OCC COM HEAT P/N 24-11448-00009 Rev.
Page 3
English 中文 T9800 0-10 VDC FC BUS NTC OCC COM 0-10 VDC 0-10 VDC FC BUS FC BUS AO1 GND NTC OCC COM AO1 GND NTC OCC COM B 0-10 V 0-10 V FC BUS FC BUS NTC OCC COM B NTC OCC COM Low Med Low Med...
Page 4
English 中文 T9800 0-10 V 0-10 V FC BUS FC BUS NTC OCC COM B NTC OCC COM B Low Med Low Med FAN-ON FAN-ON Cool/ Heat TiO2 Cool/ FC BUS Cool/ FC BUS Heat Heat AO2 AO1 NTC OCC COM B AO2 AO1 NTC OCC COM B Low Med...
Page 5
IMPORTANT • Use this T9 Series thermostat only as an operating control. Where failure or malfunction of the T9 Series thermostat could lead to personal injury or property damage to the controlled equipment or other property, additional precautions must be designed into the system. Incorporate and maintain other devices such as supervisory or alarm systems or safety or limit controls intended to warn of, or protect against, failure or malfunction of the T9 Series thermostat.
English T9800 INSTRUCTIONS On/Off Setting: Press to turn on, press again to turn off, close the fan and valve. Mode Selection: Press M to change the working mode, for cooling, for heating, for venting, for auto cooling or heating mode. is available only for 4-pipe application or 2-pipe application when BI-FUNCTION is Change Over Sensor input.
Page 7
English T9800 PARAMETER SETTING (PART 2/2) T9800- T9800- T9800- TF20- TB21- TF21- Code 1JS0 1JA0 1JS0 Parameter Name Default Function TIO2ESP control: 00: Automatic ■ ■ TIO2ESP-CTL 01: Manual For TIO2ESP application Baud rate for BACnet MS/TP: 00:AUTO 01:9600 ■ ■...
Page 8
English T9800 PARAMETER SETTING (PART 2/3) T9800- T9800- T9800- TF20- TB21- TF21- Code 1JS0 1JA0 1JS0 Parameter Name Default Function T9800-TF20-1JS0 00: 2-pipe FCU 01: 4-pipe FCU 02: 2-pipe 3-wire valve FCU 03: 2-pipe FCU with floor heater 04: 2-pipe FCU with TiO2/ESP 05: water source heat pump 06: Floor heating/Boiler T9800-TB21-1JA0...
Page 9
English T9800 PARAMETER SETTING (PART 3/3) T9800- T9800- T9800- TF20- TB21- TF21- Code 1JS0 1JA0 1JS0 Parameter Name Default Function 00: One Heating Stage - Fan Coil ■ ■ HTG-STG 01: One Heating Stage - Floor Heating 02: Two heating stage BI polarity: ■...
○ :表示该有害物质在该部件所有均质材料中的含量均在GB/T26572规定的限量要求以下 × :表示该有害物质在该部件所有均质材料中的含量超出GB/T26572规定的限量要求 (产品中使用的物料超出SJ/T11364标准,但在欧盟RoHS中,此项为豁免,因目前技术无法有符合SJ/T11364的替代材料) Compliance Johnson Controls declares that these products are in compliance with the essential requirements and other relevant provisions of the EMC Directive and Low Voltage Directive. European Single Point of Contact: NA/SA Single Point of Contact:...