Operational Manual Haier Automatic Drum Washing Machine Model: XQG50-RC800TXBS XQG50-RC600TXBS XQG50-RC1000TXB Patent No.: 196.000.017.00 • Please read this carefully before use • Keep this manual in a safe place. Table of Contents Before Use Washing Machine Diagram ..… Matters Needing Attention ……………... 1-3 Installation ………………………………..
Washing Machine Diagram Detergent distribution drawer Operational buttons Door Porthole Power cable Spare earth terminal Back plate screw (×3) Drainage hose Programming knob Door button Wash temperature knob Anti-vibration U steel Drainage hose clip Packing bolt (×3) Back plate Safety Signs For your safety, any instructions in this manual with this...
3. Fuses in the power circuit should be rated for 15A. Refer to a washing machine technician or a Haier designated service point for power cable replacement. 5. Do not use flammable detergent or dry cleaning agent;...
Page 4
Matters Needing Attention 8. The washing machine should not be installed outdoors or in a damp place. In the event of water leakage or splashes allow the machine to dry naturally. 10. Keep away from heat sources and direct sunlight to prevent plastic and rubber components from aging.
Page 5
Matters Needing Attention 3. Do not place heavy, heating source or wet articles on the top of the washing machine. 5. Before washing, do up zippers, buttons and clothes straps and put small articles, such as socks, laces or bras, into a washing bag or a pillow.
Installation As shown in Fig. 1, remove all the packing materials (including the foam base). Check attachments and materials with reference to the Packing List, as shown in Fig. 2. Name Model XQG50- RC800T XQG50- RC600T XQG50- RC1000T Dismantle the packing bolts as shown in Fig. 3. The packing bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process.
Joining the inlet hose to the washing machine Connect the nut on the inlet hose to the connector on the water valve. Tighten the nut to secure the hose Drainage hose The height of the drainage outlet must be 80cm ~ 100 cm. To prevent the drainage hose from dropping off, fix it to the drainage hose clip at the back of the washing machine.
Control panel <W1> Programming (after the power is cut) Intense -- Cotton fabrics 1 Pre-wash 5 Soften A Standard wash 2 Standard wash 6 Spinning B Quick wash · Finish 3 Quick wash C Rinse 4 Rinse D Soften D: Super delicate E: Half load I: The door can only be opened 3 minutes after the power is turned off or the operation is finished Programming (after the power is cut)
Operational Functions Wash programming knob By turning the knob clockwise, the required program can be selected Operational Programming Guide (Refer to Caution: Turn off the power before setting a program; turn the program knob clockwise; never turn it counterclockwise. Wash temperature knob By turning the knob clockwise, the required temperature can be selected.
Page 10
Operational Functions Half load (Economical wash) Pressing this button will reduce the consumption of water in the washing process. It is recommended that this program be used when doing a small laundry load. Do not forget to reduce the amount of detergent used. Without spinning Press this button down, the machine will run without spinning but drain.
Page 11
Guide to Operational Program Selection For XQG50-RC600TXBS / XQG50-RC800TXBS Mode Selection Recommended (Program knob position) Laundry Pre-wash Heavy soil Standard Medium fabrics Quick wash Fast colors and medium soil cotton Rinsing Capable of bleaching if bleaching powder added Capable of softening if Softening softener added Spin drying...
Page 12
Standard Rinsing Capable of softening Softening if softener added Anti-crease Washing soaking stops Spin drying Draining Finish Delicate wash program ends and the washing machine stops operation. ○ indicates that softener or bleach can be added if needed; O indicates that detergent must be added; X indicates that detergent must not be added; Wash Note: temperature indicates the maximum temperature.
Page 13
Guide to Operational Program Selection For XQG50-RC1000TXB Mode Selection Recommended (Program knob position) Laundry Pre-wash Heavy soil Medium soiled fabrics Standard Quick wash Fast colors and medium soil cotton Super quick wash Fading and medium soil cotton Capable of bleaching if...
Page 14
Standard Rinsing Capable of softening if Softening Anti-crease Washing soaking stops Spin drying Draining Finish Delicate wash program ends and the washing machine stops operation. O indicates that softener or bleach can be added if needed; O indicates that detergent must be added; X indicates that detergent must not be added; The Note: compartment 1 is not for detergent;...
Preparation Power supply Plug in the power supply (187-242) V/50Hz Detergent selection The washing performance is determined not only by the function washing machine, but also by the quality of the detergent used. It is recommended that you use non-foaming detergent Use special detergent for synthetic and woolen goods.
Washing Methods Loading Open the door, put in the laundry piece by piece. Close the door tight Note: When first using the Washing machine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine.
Hints for Saving Energy Setting washing temperature Set the washing temperature as required, or otherwise, set at position * when heating is not needed. (Refer to the programming guide for maximum temperature allowed for each washing procedure) Selecting the function button Select function buttons as required (refer to the directions printed on the operation panel) Washing Press the power button and the washing machine will automatically commence the programmed...
Maintenance Turn off the water tap and pull out electricity plug after each wash. Open the porthole to prevent formation of moisture and odors. If the washing machine is left idle for a long period, drain the water in the machine and replace the drainage hose. Unplug the machine during with soap liquid to clean the machine case and rubber components.
Troubleshooting The following circumstances do not constitute problems. Do not contact the maintenance service until the problem has been confirmed. Problem The washing machine fails to operate Washing machine cannot be filled with water The machine is draining while is being filled Drainage failure Strong vibration during spin drying...
Specifications Model Item RC800TXBS Power supply Max working current (A) Water pressure (MPa) Washing power (W) Spinning power (W) Rated load (Kg) Spinning speed (r/min) Washing programs Water heating power (W) Dimensions 850×485×595 (H×L×W mm) Weight (Kg) XQG50- XQG50- RC600TXBS 220 V (50Hz) 220 V (50Hz) 0.05≤P≤1...