Table of Contents
Advertisement
265-268
0100001
269-272
277-280
1010001
281-284
289-292
0001001
293-296
301-304
1101001
305-308
313-316
0111001
317-320
325-328
1000101
329-332
337-340
0010101
341-344
349-352
1110101
353-356
361-364
0101101
365-368
373-376
1011101
377-380
385-388
0000011
389-392
397-400
1100011
401-404
409-412
0110011
413-416
421-424
1001011
425-428
433-436
0011011
437-440
445-448
1111011
449-452
457-460
0100111
461-464
469-472
1010111
473-476
481-484
0001111
485-488
493-496
1101111
497-500
505-508
0111111
509-512
Installation & Operation Guide
Page 15
1100001
273-276
0010001
0110001
285-288
1110001
1001001
297-300
0101001
0011001
309-312
1011001
1111001
321-324
0000101
0100101
333-336
1100101
1010101
345-348
0110101
0001101
357-360
1001101
1101101
369-372
0011101
0111101
381-384
1111101
1000011
393-396
0100011
0010011
405-408
1010011
1110011
417-420
0001011
0101011
429-432
1101011
1011011
441-444
0111011
0000111
453-456
1000111
1100111
465-468
0010111
0110111
477-480
1110111
1001111
489-492
0101111
0011111
501-504
1011111
1111111
TESTING
If desired, the dimmer may be tested without any control signal input
by moving SWITCH #8 to the off and then the on position on both of
the dimmer firing cards after the system is energized. This will cause all
dimmer channels to go to full intensity for testing load circuits. Dimmers
will ignore all control signals in this case.
NOTE:
If Switch #8 is set on before power is applied to the dimmers, then the
lighting loads associated with that firing card will come to 50% intensity
(full on for CR's) when power comes on. This is useful for emergency
lighting purposes. The console or remote panels may take control after
light come on.
CAUTION
INSPECT INSIDE OF DIMMER PACK FOR LOOSE BITS OF WIRE OR HARDWARE
THAT MAY HAVE FALLEN ONTO THE CONTROL CIRCUIT BOARDS AND BE SURE
ALL INPUT AND LOAD WIRING IS COMPLETE BEFORE ENERGIZING ELECTRICAL
SERVICE TO DIMMER.
CONTROL WIRING
Control wiring to the 2408CD should be Class 2 wiring. All control wiring
must stay below the barrier separating the control wiring compartment
from the load wiring. All control wiring must exit out of either of the
1/2"-3/4" knockouts located in the control wiring compartment. Several
types of low voltage control inputs may be employed as discussed below.
Under no circumstances can any control signal input exceed 15 volts.
Individual 0-10 VDC control wiring
Each of the eight dimmer channels of the 2408 CD/CR may be operated
by a 0-10 VDC control voltage. This type of control will provide 0%
intensity at 0 volts and 100% intensity at 10 volts. Any or all of the
dimmer channels may be operated in this manner simultaneously with
either of the multiplex control inputs. Each dimmer will respond to the
greater of any control inputs.
Connect each of the plus control wires to the desired dimmer channel
connections (see figure 3) on each of the dimmer firing cards. Connect
the common control wire to one of the COMMON connections provided
on the power supply card. This control input impedance is 4.7K ohms.
Installation & Operation Guide
Page 8
Advertisement
Table of Contents
